Flipsky 5065 200KV 1800W

Contents

Flipsky Battle Hardened 5065 Brushless DC Motor User Manual

1. Introduction

This manual provides essential information for the safe and efficient use of your Flipsky Battle Hardened 5065 200KV 1800W Sensored Outrunner Brushless DC Motor. This high-performance motor is designed for various applications including robots, ebikes, scooters, and skateboards. Please read this manual thoroughly before installation and operation.

Front view of the Flipsky 5065 motor with an 8mm D-shaft.
Figure 1: Front view of the Flipsky 5065 Brushless DC Motor.

2. Safety Information

⚠️ WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage of any connected battery systems. Failure to do so may result in serious injury or property damage.

  • Always ensure proper insulation of all electrical connections.
  • Do not operate the motor beyond its specified voltage and current limits.
  • Keep hands and loose clothing away from rotating parts during operation.
  • Ensure the motor is securely mounted before use.
  • Disconnect power before performing any maintenance or adjustments.
  • Use appropriate personal protective equipment (PPE) when working with electrical components.

3. Package Contents

Please check the package for the following items:

  • 1x Flipsky Battle Hardened 5065 200KV 1800W Sensored Outrunner Brushless DC Motor

Note: Additional components such as Electronic Speed Controllers (ESC), batteries, and mounting hardware are sold separately.

4. Setup

4.1. Mounting

The motor features four M4 mounting holes on its face. Ensure the motor is securely fastened to your application's frame or mount using appropriate M4 screws. Refer to the dimensional diagram for precise hole spacing.

4.2. Electrical Connections

This motor is a sensored brushless DC motor, requiring connection to a compatible sensored Electronic Speed Controller (ESC).

  1. Power Leads: Connect the three main power leads (typically thicker wires) from the motor to the corresponding phase outputs (A, B, C or U, V, W) on your ESC. The motor is equipped with an MT30 male connector for power.
  2. Sensor Cable: Connect the 6-pin sensor cable from the motor to the sensor port on your ESC. Ensure the orientation is correct to avoid damage. The motor uses a PH2.0-6P connector for the sensor.
  3. Battery: Connect your battery pack to the ESC's power input. Ensure the battery voltage is within the motor's specified range (6-12S LiPo).
Dimensional drawing of the Flipsky 5065 motor showing dimensions and connector types.
Figure 2: Dimensional drawing of the Flipsky 5065 motor. The diagram shows a motor diameter of Ø49.2mm, mounting holes 4-M4*5, and a shaft diameter of Ø8mm with a D-flat. Cable lengths are approximately 290mm and 330mm. Connectors are MT30 male for power and PH2.0-6P for the sensor.

5. Operating Instructions

  1. ESC Configuration: Before first use, configure your ESC according to its manual and the motor's specifications (KV, pole count, current limits). Proper ESC calibration is crucial for smooth operation.
  2. Initial Test: With the motor unmounted or under no load, perform a low-power test to ensure correct rotation direction and smooth operation. If the direction is incorrect, reverse any two of the three main power leads (or adjust in ESC software).
  3. Load Operation: Gradually increase power during initial runs under load to monitor motor temperature and performance.
  4. Temperature Monitoring: Avoid operating the motor at excessively high temperatures, as this can damage windings and magnets. If the motor becomes too hot to touch, reduce load or allow it to cool.

6. Maintenance

  • Cleaning: Regularly clean the motor to remove dust, dirt, and debris, especially from cooling fins and bearings. Use compressed air or a soft brush.
  • Bearing Inspection: Periodically check the motor bearings for any signs of wear, noise, or excessive play. Worn bearings should be replaced by a qualified technician.
  • Connection Check: Ensure all electrical connections remain secure and free from corrosion.
  • Shaft Inspection: Check the motor shaft for any bends or damage that could affect performance.

7. Troubleshooting

SymptomPossible CauseSolution
Motor not spinningNo power to ESC; ESC not armed; Motor/ESC connection issue; Damaged motor/ESCCheck battery, ESC status, all connections. Test motor with another ESC or ESC with another motor if possible.
Motor cogging/stutteringIncorrect sensor connection; Sensor damage; ESC timing issues; OverloadCheck sensor cable and connection. Adjust ESC timing. Reduce load.
Motor runs hotOverload; Incorrect gearing; Insufficient cooling; Short circuit in windingsReduce load, adjust gearing, improve airflow. Inspect motor for damage.
Motor makes unusual noiseWorn bearings; Loose parts; Debris inside motorInspect bearings, check for loose screws, clean motor.

8. Specifications

FeatureSpecification
ModelBattle Hardened 5065
Max Power1800W
Motor KV200KV
Max Current38A
Voltage Range6-12S LiPo (22.2V - 44.4V)
Max Torque1.7 N.M
Weight0.5KG
Motor Structure12N/14P
Diameter x Length49mm x 63.5mm
Shaft Diameter8mm / D-Shaft
Power ConnectorMT30mm (16AWG wire)
SensorYes (PH2.0-6P connector)
DesignBrushless Outrunner
CertificationCE
OriginMainland China

9. User Tips

No specific user tips were available from provided reviews or Q&A content for this product.

10. Warranty and Support

10.1. Warranty Policy

The warranty period for this electronic product (motor) is 2 months, effective from the 7th day after shipment (as per logistic record). The warranty covers manufacturing defects.

Conditions Not Covered by Warranty:

  • Lack of proof of purchase channel.
  • Mechanical damage to electronic components or PCB.
  • PCB damage due to soldering iron traces (excluding solderable bullet connectors).
  • Water damage or external impact damage (for non-waterproof products).
  • Abnormal applications beyond the product specifications.
  • Products purchased from channels other than official Flipsky distributors.
  • Group-buy policy: Warranty period follows the 7th day after the original group-buy order's shipment.
  • For products transferred by personal second transaction, the warranty is invalid.

Most products are tested before shipment. Any uncertain connection or information for VESC/Motors settings, please contact support before your installation. No term warranty, in no case shall Flipsky's liability be greater than the actual purchase price of the product.

10.2. Support

For warranty claims, technical support, or any product-related inquiries, please contact Flipsky customer service at flipsky_service@outlook.com. Please provide your original source order number or warranty card number when contacting support.

© 2023 Flipsky. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.