1. Introduction
The HOBBYWING QuicRun WP 8BL150 G2 is a high-performance 3-6S Waterproof Brushless Sensorless Electronic Speed Controller (ESC) designed for 1/8th scale RC trucks and monster trucks. This ESC features exceptional protection, an efficient cooling system, and a durable electronic switch, ensuring reliable operation in various conditions.
This manual provides essential information for the proper setup, operation, and maintenance of your QuicRun WP 8BL150 G2 ESC. Please read it thoroughly before use to ensure safe and optimal performance.
2. Safety Information
- Always disconnect the battery from the ESC when not in use to prevent accidental activation.
- Ensure all connections are secure and properly insulated to avoid short circuits.
- Operate your RC vehicle in a safe environment, away from people, pets, and obstacles.
- Keep the ESC away from extreme temperatures and direct sunlight.
- While the ESC is waterproof (IP67 rated), avoid prolonged submersion in water. The protection is for splash-proof, water-proof, and dust-proof under normal use. Protection performance may decline due to daily wear and aging. Do not soak in water for a long time, otherwise the product may be damaged.
- Children under 14 years old should be supervised by an adult when operating RC vehicles.
3. Package Contents
Upon unboxing, verify that all components are present:
- HOBBYWING QuicRun WP 8BL150 G2 ESC
- Electronic Power Switch
- Mounting accessories (e.g., zip ties, double-sided tape, mounting plate)
- User Manual (this document)
- Stickers
Video: Unboxing the HOBBYWING QuicRun WP 8BL150 G2 ESC and its accessories.
Image: The QuicRun WP 8BL150 G2 ESC with its connected electronic power switch.
4. Specifications
Image: Detailed specifications for the QuicRun WP 8BL150 G2 ESC.
| Category | Parameter | Value |
|---|---|---|
| Type | Product Name | QuicRun WP 8BL150 G2 |
| Product Number | 30109003 | |
| Scale | 1/8th | |
| Brushed/Brushless | Brushless | |
| Sensored/Sensorless | Sensorless | |
| Waterproof | Waterproof (IP67) | |
| Specifications | Cont./Peak Current | 150A/950A |
| Input Voltage | 3-6S Lipo | |
| BEC Output | Switch Mode 6V/7.4V @6A | |
| Wires & Connectors | Input Wires | Black-10AWG-150MM / Red-10AWG-150MM |
| Output Connectors | 6.5mm Gold (female) |
Image: Additional specifications for programming, size, weight, and applications.
| Category | Parameter | Value |
|---|---|---|
| ESC Programming via | SET Button on ESC | Not Supported |
| LED Program Box | Supported | |
| LCD G2 Program Box | Supported | |
| OTA Programmer | Not Supported | |
| Program Port | Separate Program Port | |
| Firmware | Firmware Upgrade | Not Supported |
| Size & Weight | Size | 60*48*40.4mm |
| Weight | 169.5g (Included wires) | |
| Applications | Motors | Sensorless / Sensored Brushless Motor (only in sensorless mode) |
| Vehicles | 1/8th Truck, Monster truck | |
| With 4S Lipo: KV ≤ 3000 | ||
| With 6S Lipo: KV ≤ 2400 4274 size motor |
Image: The ESC features a super large built-in capacitor with 2040 uF capacity, eliminating the need for external capacitors.
Image: The upgraded BEC provides 6V/7.4V at 6A continuous current, with a maximum of 12A, supporting high-voltage servos.
5. Setup & Installation
5.1 Mounting the ESC
Securely mount the ESC in your vehicle chassis using the provided double-sided tape or mounting plate. Ensure good airflow around the ESC for optimal cooling.
Image: Example installation of the ESC within an RC truck chassis.
5.2 Wiring Connections
Connect the ESC to your motor, battery, and receiver according to the following guidelines:
- Motor Connection: Connect the three output wires from the ESC to the motor's three phase wires. Ensure correct phasing for proper motor rotation.
- Battery Connection: Connect the red and black input wires (10AWG) from the ESC to your 3-6S LiPo battery. Ensure polarity is correct (red to positive, black to negative).
- Receiver Connection: Plug the small signal cable from the ESC into the throttle channel (usually channel 2) of your RC receiver.
- Electronic Switch: Connect the electronic power switch to the designated port on the ESC.
Image: Side view of the ESC illustrating the various wire connections.
6. Operation
6.1 Powering On/Off
To power on the ESC, ensure the battery is connected, then press and hold the button on the electronic power switch until the LED indicator illuminates. To power off, press and hold the switch button again until the LED turns off.
6.2 Basic Control
Once powered on, the ESC will respond to throttle inputs from your transmitter. Ensure your transmitter is properly bound to your receiver and calibrated for the ESC.
7. Programming
The QuicRun WP 8BL150 G2 ESC supports programming via a separate program port using specific HOBBYWING programming devices.
- LED Program Box: Supported
- LCD G2 Program Box: Supported
- SET Button on ESC: Not Supported
- OTA Programmer: Not Supported
Refer to the manual of your HOBBYWING LED Program Box or LCD G2 Program Box for detailed programming instructions.
8. Maintenance
- Cleaning: Regularly clean the ESC and its cooling fan to remove dirt, dust, and debris. Use a soft brush or compressed air.
- Inspection: Periodically inspect all wires and connectors for signs of wear, damage, or corrosion. Ensure all connections are tight.
- Cooling System: The ESC features an efficient cooling system with a patented copper heat conduction bus bar and a fan. Ensure the fan is free from obstructions and operating correctly to maintain optimal temperature.
- Water Resistance: The IP67 rating provides protection against dust and water splashes. After exposure to wet conditions, ensure the ESC is thoroughly dried before storage or next use. Avoid prolonged submersion.
Image: The efficient cooling system with a copper heat conduction bus bar and fan ensures safe operating temperatures.
Image: The capacitor overheating protection function helps prevent damage from overload usage.
9. Troubleshooting
- No Power: Check battery connection, electronic switch connection, and ensure the battery is charged.
- Motor Not Responding: Verify receiver connection to the ESC, check transmitter settings, and ensure motor wires are securely connected.
- Erratic Operation: Check for loose connections, interference, or incorrect programming settings.
- ESC Overheating: Ensure proper airflow, clean the cooling fan, and verify that the motor/gear ratio is appropriate for your vehicle.
10. User Tips
- The assembly process for this ESC is generally straightforward and easy.
- Be aware that options for higher than 50% braking and higher drag braking may not be available with this unit.
- The ESC is constructed from composite material, contributing to its durability.
- This product is suitable for users aged 14 years and older.
11. Warranty & Support
For warranty claims or technical support, please contact the HOBBYWING customer service or your authorized dealer. Keep your purchase receipt as proof of purchase.