JIKONG B1A8S20P

Contents

JIKONG Smart BMS B1A8S20P Instruction Manual

Comprehensive guide for setup, operation, and maintenance of your Smart Battery Management System.

1. Introduction

The JIKONG Smart BMS B1A8S20P is an advanced Battery Management System designed to optimize the performance and extend the lifespan of your battery packs. It supports LiFePo4, Li-ion, and LTO battery types across 3 to 8 series configurations, handling up to 200A charge/discharge current. This BMS integrates active balancing, heating functionality, and various communication interfaces like Bluetooth, CAN, and RS485 for smart monitoring and control.

Video: Overview of JIKONG Active Balance BMS features and applications.

JIKONG Smart BMS B1A8S20P features

Image: Key features of the JIKONG Smart BMS B1A8S20P, including V19 version, BT/Display/Heat/CANBUS functions, 1A balance current, 4S-8S battery strings, 200A charge/discharge, and dimensions (152.25x127.26x15.6mm).

2. Specifications

AttributeValue
Brand Namesmart jikong bms
ModelB1A8S20P
TypeLIFEPO4 Battery BMS
Battery Strings3S-8S
Battery TypeLiFePo4/Li-ion/LTO
Charge/Discharge Current200A
Charging Current200A
Balance FunctionPassive Balanced BMS
Balance Current1A
Handware or SmartSMART BMS
Charge and Discharge PortCommon Port BMS
FunctionOvercharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection, BT/RS485/CAN/Heat
Usage ScenarioPower BMS, Energy Storage BMS
CertificationCE, FCC, RoHS
High-concerned chemicalNone
OriginMainland China
Detailed parameter table for various JIKONG BMS models

Image: Detailed parameter table showing specifications for various JIKONG BMS models, including string support, balance current, continuous current, and interface options.

Product certifications for JIKONG BMS

Image: Product certification documents for JIKONG BMS, including RoHS, FCC, and CE certifications.

3. Package Contents

Upon receiving your JIKONG Smart BMS, please verify that all components are present and undamaged:

JIKONG Smart BMS package contents

Image: Contents of the JIKONG Smart BMS package, including the BMS unit, operation manual, screws (x4), NTC (40cm), Switch (50cm), CAN cable (25cm), and two sets of Wires (70cm).

  • JIKONG Smart BMS Unit
  • Operation Manual
  • Screws (4 pieces)
  • NTC Temperature Sensor (40cm)
  • Switch (50cm)
  • CAN Cable (25cm)
  • Balance Wires (2 sets, 70cm each)
  • Pack Box

4. Setup and Installation

4.1. Wiring Diagram

Carefully follow the wiring diagram below to connect the BMS to your battery pack, load, and charger. Incorrect wiring can cause damage to the BMS or battery.

JIKONG Smart BMS wiring diagram

Image: Detailed wiring diagram for the JIKONG Smart BMS, showing connections for the battery pack (B+, B-, sampling cables), load, and charger.

4.2. Initial Connection Steps

  1. Connect the protection board and battery pack: Ensure that the last power cord (B+) is connected to the main positive pole of the battery. The total voltage of the battery pack must be greater than 20V (for default BMS) or 10V (for 4S BMS) before starting up.
  2. Activate the BMS: Use the display activation button or an additional switch to activate the BMS.
  3. Prepare your mobile device: Turn on GPS and Bluetooth on your mobile phone.
  4. Connect via APP: Open the JIKONG BMS APP. Click on the top left corner of the APP to search for devices. Select your device name to connect. The default password is '1234'.
  5. Set parameters: For the first start-up, parameters need to be set. The default parameter password is '123456'. Simply set the number of units (battery strings) and battery type (LiFePo4/Li-ion/LTO).
  6. Verify status: Once parameters are set, go back to the real-time status page. Check the battery status to ensure no error messages are prompted and normal operation. Blue indicates the highest voltage, and red indicates the lowest voltage.
JIKONG Smart BMS Bluetooth APP interface

Image: Screenshot of the Smart BT APP interface, showing real-time battery monitoring, parameter modification support, BMS balance switch control, and Android/iOS system support.

4.3. Interface Function Description

JIKONG Smart BMS interface ports

Image: Diagram showing the various ports on the JIKONG Smart BMS, including Temperature sensor, customized functions, RS485 (by default), LCD (by default), and Heat Function (customization needed).

  • Temperature sensor interface: All models of JKBMS are equipped with this.
  • RS485 interface: All models of JK BMS are configured with this.
  • LCD interface: All models of JK BMS are equipped with this.
  • CAN interface: Only configurations with "CAN" in the model name include this.
  • Heating interface: Only configured with "Heat" in the model name include this.
JIKONG Smart BMS connection diagram for peripherals

Image: Connection diagram illustrating how to connect peripherals like NTC, CAN, RS485, Switch, and LCD to the JIKONG Smart BMS.

JIKONG Smart BMS rich interface options

Image: Diagram highlighting the rich interface options of the JIKONG Smart BMS, including CAN, RS485, BT, NTC, Soft Switch, SOC Indicator, Key Switch, Active Equalizer, GPS, Heat, and Sampling ports.

5. Operating Instructions

5.1. Smart Energy Working Mode Switching

The BMS supports various working modes to optimize battery usage and protection:

Smart energy working mode switching diagram

Image: Diagram illustrating the four smart energy working modes: Storage Mode, Normal Working Mode, Standby Mode, and Shutdown. Arrows indicate transitions between modes based on charging activation, long unused periods, and reaching shutdown voltage.

  • Storage Mode: In transportation, offline, or wireless transmission off mode, the BMS is in storage mode, which does not consume battery pack current.
  • Normal Working Mode: When the charger is inserted in storage mode and off mode, the BMS will immediately return to normal working mode, and all protection functions, equalization functions, and communication functions will return to normal working.
  • Standby Mode: When the battery pack is in the static state (no charge and discharge current) and no equilibrium current, the BMS will automatically enter standby state after the set time (1-30 days can be set) is exceeded.
  • Shutdown: To prevent the BMS from wasting power for a long time and damaging the battery pack, the BMS has an automatic shutdown voltage, and the BMS automatically shuts down when a cell falls below the shutdown voltage.

5.2. Heating Function

The heating function is designed to protect the battery during charging in low-temperature conditions.

  • The heating function is activated by detecting the battery temperature, combined with low-temperature protection during charging. The status of the charger achieves electricity pool heating control.
  • Not all BMSs support the heating function. Only BMS models with "Heat" in their names support this feature.
  • The heating interface requires an external heating film or charger. The green cable connects to the heating film, and the red and black cables connect to the charger. The maximum heating power is 3A, and the maximum heating voltage is 100V.

Heating Conditions:

  • The battery temperature is lower than the low-temperature protection temperature for charging.
  • By connecting the heating film for heating, the APP will activate heating, which will consume battery power.
  • Heat through the charger: This is related to the protection board hardware and charger. Please confirm the technical status before ordering.

5.3. Protocol Docking and Compatibility

The JIKONG Smart BMS is compatible with mainstream inverter communication protocols in the market, and settings can be easily configured through the mobile APP.

JIKONG Smart BMS protocol docking and supported CAN protocols

Image: Diagram showing the protocol docking capabilities of the JIKONG Smart BMS, compatible with various inverter brands. A table lists supported CAN protocols such as Low-voltage hybrid inverter CAN communication protocol, PYLON CANBUS Protocol V1.2, Growatt xxSxxP ESS Protocol V2.01, CAB-BUS_BMS_Protocol_201707, INVT BMS CAN Bus protocol V1.02, GoodWe LV BMS Protocol (CAN) V1.7 (For ES/EM/S-BP/BP Series), FSS-ConnectingBat-TI-en-10 | Version 1.0, and PACE BMS Modbus Protocol for RS485.

6. Maintenance

  • Keep the BMS clean and free from dust and moisture.
  • Regularly check all wiring connections for tightness and corrosion.
  • Ensure proper ventilation around the BMS to prevent overheating.
  • Avoid exposing the BMS to extreme temperatures or direct sunlight for prolonged periods.
  • Periodically check the battery cell voltages via the APP to ensure they remain balanced.

7. Troubleshooting

7.1. BMS Does Not Turn On

  • Ensure that the last "B+" line of the cable has been correctly connected to the positive pole of the battery.
  • Start up after charging and ensure that the charger voltage is greater than 4V of the battery pack voltage.
  • Check whether the charger has voltage output.

7.2. Inaccurate Voltage Readings

  • Measure the actual total voltage of the battery pack with a multimeter.
  • Enter the actual total voltage into the "voltage calibration" setting on the parameter setting page in the APP.

7.3. Inaccurate Current Readings

  • The B- and P- terminals of the protection board are two 7AWG wires, both of which need to be connected in parallel. Otherwise, it will lead to current errors.
  • Measure the actual current of the battery pack with a clamp meter.
  • Enter the actual current into the "current calibration" setting on the parameter setting page in the APP. A larger actual current generally leads to higher calibration accuracy.

7.4. Inaccurate Capacity Readings

  • An initial capacity estimated based on the monomer voltage when the protection board is powered on for the first time may be inaccurate.
  • To calibrate, discharge the battery pack to the cut-off voltage and then fully charge it. The charging process should not be interrupted.

7.5. Designed String Number Inconsistent with Actual String Number

  • Check whether the "unit quantity" in the parameter settings is set correctly in the APP.
  • If there is no voltage in two or more strings in the middle, check whether the acquisition cable has fallen off or is damaged.

8. User Tips

  • This BMS is versatile and suitable for controlling various battery configurations, including four LiFePo4 3.2 volt 150Ah cells.
  • Always double-check all connections before powering on the system to prevent potential damage.
  • Utilize the mobile app for real-time monitoring and fine-tuning of parameters to get the best performance from your battery pack.

9. Warranty and Support

For any technical assistance, warranty claims, or further inquiries, please contact the seller or manufacturer directly. Ensure you have your product model and purchase details ready for efficient support.

Download Links:

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.