1. Introduction
The XMT*-618T series intelligent digital display time and temperature regulator, specifically the XMTD-608 model, is an advanced instrument designed for precise temperature control and timing. It features a dual-row, four-digit display for both measured temperature (PV) and set value (SV), along with a countdown timer. This versatile controller supports multiple signal inputs and time control options, making it suitable for various industrial applications such as machinery, chemical engineering, ceramics, light industry, metallurgy, petrochemical, and heat treatment.
The instrument operates with four intuitive keys for easy parameter setup and utilizes both two-position and PID control methods for stable and accurate performance.
2. Specifications
2.1. Technical Parameters
| Parameter | Description |
|---|---|
| Measurement Error | ± 0.5% FS ± 1B, additional cold end compensation error ≤ ± 2°C |
| Sensor Input Types | TC/RTD Universal Input (K, E, S, B, R, T, J, PT100, CU50) |
| Temperature Measurement Range | 0-1300℃ (32-2372℉) |
| Output Type | SSR (3-32V) / Electromagnetic Relay Dual Output |
| Relay Output Contact Capacity | AC220V 5A (resistive load), cycle adjustable for 2 to 120 seconds |
| Time Range | 0-9999 seconds / 0-9999 minutes (optional) |
| SSR Drive Signal | Current ≥ 15mA, no-load voltage ≥ 9V, cycle about 2s |
| Working Current | AC85-265V, 50/60Hz, power consumption < 3W |
| Working Environment | 0-50°C, relative humidity ≤ 85%, non-corrosive and non-strong electromagnetic radiation occasions |
| Alarm Quantity | 1 piece (High temperature alarm, adjustable) |
| Display Size | 1.9 Inches & Under |
| Direct Load Capacity | Can be directly connected to resistive 800W equipment without an AC contactor. |
2.2. Product Dimensions
The XMTD-608 controller has the following physical dimensions:
- Panel Size: 72mm x 72mm
- Cut Size: 68mm x 68mm
- Depth: 80mm

3. Setup and Installation
3.1. Unboxing and Initial Inspection
Upon receiving your XMTD-608 controller, carefully unbox it and inspect for any visible damage. Ensure all components, including the controller, manual, and mounting clips, are present.

Watch the unboxing video for a visual guide:
3.2. Wiring Diagram
Proper wiring is crucial for the safe and correct operation of the XMTD-608. Refer to the wiring diagram provided on the instrument casing and the figures below. Always ensure the power supply, sensor, and control circuit are connected correctly before powering on the instrument.



Note: The specific wiring of the instrument must always follow the wiring diagram printed on the instrument casing.
4. Operation
4.1. Instrument Panel Overview
The front panel of the XMTD-608 features a dual digital display and control buttons:

- PV (Process Value): Displays the measured temperature value.
- SV (Set Value): Displays the target temperature or time set value.
- OUT Light: Indicates output status.
- AT Light: Indicates auto-tuning (Self-tuning) status.
- ALM Light: Indicates alarm status.
- TIME Light: Indicates timer status.
- SET Key: Used to enter menu, save settings, and navigate.
- Left Key (<): Used for digital shifting during parameter modification.
- Reduce Key (V): Used to decrease parameter values.
- Increase Key (A): Used to increase parameter values.
4.2. Initial Power-On and Normal Operation
- Connect the power supply, sensor, and control circuit according to the wiring diagram.
- Power on the instrument. The instrument will perform a self-check for approximately 1 second.
- After self-check, the instrument enters the normal measurement and control state. The upper PV window will display the measured value, and the lower SV window will display the set value.
4.3. First Level Menu (Temperature and Time Setting)
- Temperature Setting (SP):
- Press the SET key for 3 seconds to enter the temperature setting value change state.
- The upper PV window will display "SP", and the lower SV window will show the current temperature set value.
- Use the V (reduce) or A (increase) keys to modify the value. Long press for fast adjustment.
- Press the SET key to save and exit. If no key is pressed for 10 seconds, it will automatically save and exit.
- Time Setting (TE):
- Press the SET key for 3 seconds to enter the time setting value change state.
- The upper PV window will display "TE", and the lower SV window will show the current time set value.
- Use the V (reduce) or A (increase) keys to modify the value. Long press for fast adjustment.
- Press the SET key to save and exit. If no key is pressed for 10 seconds, it will automatically save and exit.
4.4. Internal Parameter Settings (Instrument Flow Diagram)
The XMTD-608 has a comprehensive set of internal parameters for fine-tuning its operation. These parameters are organized into a multi-level menu structure. Refer to the Instrument Flow Diagram (Figure 7) for a visual guide to navigating and setting these parameters.

- Accessing Secondary Menu: Press the SET key for 3 seconds. The upper window displays parameter symbols (e.g., AL, SC, P), and the lower window displays their values.
- Modifying Parameters: Use the V (reduce) or A (increase) keys to change values. Long press for quick adjustments.
- Saving and Navigating: Press the SET key to save the current parameter and move to the next. The instrument will automatically save and exit after 10 seconds of inactivity.
- Accessing Third Level Menu: Simultaneously press the SET + A keys to enter the third-level menu. The setting method is similar to the secondary menu.
Key Parameters and Their Functions:
- SP (Temperature Setting Value): Directly modify the target temperature.
- TE (Time Setting): Directly modify the timer duration (0-999).
- AL (Temperature Upper Limit Alarm): Sets the upper limit for temperature alarm (0-100).
- SC (Measurement Error Correction): Corrects the measured value by adding or subtracting a value (-20.0 to 20.0).
- P (Proportional Band): Determines the proportional gain for PID control (0-99.9 to 200). Setting to 0 switches to two-position control.
- I (Integral Time): Eliminates residual deviation from proportional control (0-999).
- d (Derivative Time): Prevents output fluctuations and improves control stability (0-200).
- Hy (Main Control Return Difference): Only meaningful in binary control (0-20).
- AF (Self-tuning Parameters): 'OFF' disables self-tuning, 'On' enables it.
- LoC (Electronic Lock): Locks parameters (0-50). If LOC=At0, all parameters can be modified.
- Sn (Input Type): Freely interchangeable input signals (K, E, S, B, R, T, J, PT100, CU50).
- CoL (System Function Selection): 0=Heating control, 1=Refrigeration control.
- uIF (Temperature Unit Selection): Switches between Celsius (°C) and Fahrenheit (°F).
- AH (Alarm Return Difference): Sets the difference for alarm return.
- LEd (Display Digits): Selects between four-digit and three-digit display.
- dF (Filter Coefficient): (1-99)
- ALF (Deviation Temperature during Countdown): When INT=1,2, the instrument starts countdown when temperature reaches SP-ALT value.
- Ar (Integral Overshoot Suppression): (0-100) Invalid when P=0.
- UPE (Timing Unit Selection): 0-10 for seconds (S), 1 for minutes (Min).
- ACt (Alarm Mode Selection): Various alarm modes (No alarm, Upper limit deviation, Lower limit deviation, In band, Out of band, Process value upper limit, Process value lower limit).
- POP (Decimal Separator Displacement): (0-1)
4.5. Self-Tuning Function
Self-tuning is used to automatically optimize the PID parameters (P, I, D) for stable and accurate control, especially when the instrument is first used or environmental conditions change. This avoids manual, tedious adjustments.
- Set the desired temperature value (SP).
- Enter the menu and set the return difference (Hy) to approximately 0.5-1.
- Set the Self-tuning parameter (AF) to 'On'. The AT light will illuminate, indicating the instrument has entered self-tuning mode.
- During self-tuning, the instrument will perform position control and oscillate up and down three times.
- After three oscillations, the instrument will determine and save new P, I, and D parameters. The AT light will turn off, and the instrument will reset to enter the control state.
Important Notes on Self-Tuning:
- If power is cut off midway during self-tuning, the instrument's memory function will cause it to restart self-tuning upon the next power-on.
- To manually exit self-tuning, set the AF parameter to 'OFF'. However, the results of the current self-tuning will be invalid.
4.6. Timing Control Function
The XMTD-608 offers flexible timing control:
- Resetting Timer: Disconnect the timing control terminal at any time to restore the timer to its initial state.
- Starting Countdown: Connect the timing control terminal to initiate the countdown operation based on the set time.
The XMTD-608T intelligent digital display time and temperature regulator provides multiple time control methods to choose from, as detailed in the internal parameter settings (Section 4.4, parameter 'in').
5. Troubleshooting
The XMT*-618T series instruments are designed for reliability. Most issues arise from improper operation or parameter settings. If you encounter a problem not listed below or cannot resolve it, please record the fault phenomenon and contact customer support.
| Fault Phenomenon | Cause Analysis | Handling Measures |
|---|---|---|
| Abnormal power on of the instrument | 1. Poor contact of the power cord 2. Power switch not closed | 1. Check the power supply connection 2. Ensure the power switch is in the ON position |
| The signal display does not match the actual situation (Display 'HH' or 'LL') | 1. Sensor model mismatch 2. Signal wiring error | 1. Check the sensor type and ensure it matches the instrument's input settings (Sn parameter) 2. Verify the signal line connections according to the wiring diagram |
| Abnormal control output | Wrong connection of output line | Check the output wiring according to the wiring diagram |
6. User Tips
- Thermocouple Calibration: If using a K-type thermocouple and observing a consistent deviation (e.g., +4°C), you can correct this using the "Measurement Error Correction" (SC) parameter in the internal settings.
- Versatile Application: This controller is suitable for various applications, including powder chambers and autoclaves, due to its combined thermostat and timer functions.
- Advanced Setup: The flexible setup system allows for precise control. For complex temperature profiles (e.g., ceramic kilns with multiple ramps and soaks), carefully review the timing function control (parameter 'in') and consider if the instrument's programmable segments meet your specific curve requirements.
7. Warranty and Support
For a comprehensive guide, including detailed diagrams and advanced settings, please refer to the official user manual PDF available at: XMTD-608 User Manual (PDF).
Our company continuously strives to improve product technology, design, and specifications. Any changes will be reflected in the actual product, and separate notifications may not always be provided.