Introduction
This manual provides detailed instructions for the safe and efficient use of your Tineco Floor one 2.0 LED Wet & Dry Wireless Handheld Vacuum Cleaner with Mop. Please read this manual thoroughly before operating the appliance and retain it for future reference. This innovative device combines powerful vacuuming with effective mopping, featuring smart dirt detection and self-cleaning capabilities to simplify your cleaning routine.
Product Overview
Key Features
- Wet & Dry Cleaning: Simultaneously vacuums and mops hard floors.
- Wireless & Handheld Design: Offers cordless convenience and easy maneuverability.
- LED Display: Provides real-time information on battery status, cleaning mode, and dirt levels.
- Smart Dirt Detection: Automatically adjusts suction power and water flow based on detected dirt levels (Red/Blue ring indicator).
- 99.9% Electrolysis Sterilization: Utilizes electrolyzed water for deep cleaning and sterilization without additional disinfectants.
- Edge-to-Edge Cleaning: Designed with a brush that cleans close to baseboards and corners.
- Constant Pressure Water Squeezing Bar: Ensures efficient dirty water recovery and removal of solid debris like hair and dust.
- High-Efficiency Single Roller Brush: Optimized for effective cleaning and designed to prevent tangles.
- Self-Cleaning Function: Simplifies maintenance by cleaning the roller brush automatically.
- Centrifugal Air Drying: Hygienically dries the roller brush and internal pipes to prevent odors and bacterial growth.
- Long Battery Life: Up to 37 minutes of runtime, capable of cleaning up to 230m² on a single charge.
- Large Water Tanks: Features an 800ml clean water tank and a 720ml dirty water tank.
- Powerful Motor: Equipped with a 100,000 rpm motor speed, 450 rpm roller brush, and 68W maximum suction power.
Components
The Tineco Floor one 2.0 LED consists of the following main components:
- Main Unit (includes motor, dirty water tank, and LED display)
- Handle
- Clean Water Tank
- Dirty Water Tank
- Roller Brush Assembly
- Charging Base
- Power Adapter
Setup
- Unpacking: Carefully remove all components from the packaging. Ensure all parts listed in the "Components" section are present.
- Handle Assembly: Insert the handle into the main unit until it clicks securely into place.
- Charging:
- Place the main unit onto the charging base.
- Connect the power adapter to the charging base and plug it into a wall outlet.
- The LED display will indicate the charging status. A full charge takes approximately 4 hours.
- Ensure the device is fully charged before first use.
- Filling the Clean Water Tank:
- Remove the clean water tank from the main unit.
- Open the tank cap and fill it with clean tap water. For enhanced cleaning and sterilization, the device uses electrolysis, so no additional cleaning solution is typically required.
- Close the cap securely and reattach the clean water tank to the main unit.
Operation
- Power On: Press the Power button on the handle to turn on the device. The LED display will illuminate.
- Cleaning Mode: The device features smart dirt detection. It will automatically adjust suction power and water flow based on the level of dirt detected on the floor. The LED display will show a red ring for heavy dirt and a blue ring for light dirt, indicating the real-time cleaning status.
- Start Cleaning: Tilt the main unit back to engage the roller brush and begin cleaning. Move the vacuum cleaner slowly over the floor surface.
- Wet & Dry Functionality: The device simultaneously vacuums solid debris and mops with clean water. The constant pressure water squeezing bar ensures dirty water is efficiently recovered into the dirty water tank.
- Edge Cleaning: Utilize the edge-to-edge brush design to clean along walls and into corners effectively.
- Power Off: Press the Power button again to turn off the device.
Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your Tineco Floor one 2.0 LED.
- Emptying the Dirty Water Tank:
- After each use, remove the dirty water tank from the main unit.
- Carefully open the tank and dispose of the dirty water.
- Rinse the tank thoroughly with clean water.
- Allow the tank to air dry before reattaching it.
- Self-Cleaning Cycle:
- Place the vacuum cleaner on its charging base.
- Ensure the clean water tank has sufficient water.
- Press the dedicated self-cleaning button (refer to the device for exact button location, usually indicated by an icon).
- The device will perform a self-cleaning cycle, washing the roller brush and internal pipes.
- After the cycle, empty the dirty water tank.
Figure 5: Illustration of the self-cleaning process. - Roller Brush Cleaning and Drying:
- Even with self-cleaning, occasionally remove the roller brush for manual inspection and cleaning.
- Remove any tangled hair or debris from the brush.
- The centrifugal air drying function helps dry the brush and pipes after cleaning, preventing odors.
Figure 6: Centrifugal air drying mechanism for the roller brush. - HEPA Filter Maintenance:
- Locate the HEPA filter (usually near the dirty water tank or motor).
- Remove the filter and tap it gently to dislodge dust.
- Rinse the filter under running water if necessary, ensuring it is completely dry before reinstallation.
- Replace the HEPA filter every 3-6 months, or as needed, depending on usage.
Troubleshooting
If you encounter issues with your Tineco Floor one 2.0 LED, please refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on | Low battery; Power button not pressed correctly | Charge the device fully; Ensure the power button is pressed firmly. |
| Poor suction or cleaning performance | Dirty water tank full; Clean water tank empty; Clogged roller brush; Clogged filter | Empty dirty water tank; Refill clean water tank; Clean roller brush; Clean/replace HEPA filter. |
| Water leakage | Water tank caps not sealed; Tanks not installed correctly | Ensure all tank caps are securely closed; Reinstall water tanks correctly. |
| Unpleasant odor | Dirty water tank not emptied/cleaned; Roller brush not dried properly | Empty and clean dirty water tank thoroughly; Run self-cleaning cycle and ensure roller brush is air-dried. |
| LED display not working | Device off; Malfunction | Ensure device is powered on; If problem persists, contact customer support. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | Tineco Floor one 2.0 LCD |
| Type | Cordless Handheld Wet & Dry Vacuum Cleaner |
| Brand Name | Esyhey |
| Battery Type | Li-ion |
| Battery Capacity | 2500mAh |
| Battery Life / Maximum Runtime | 30-60 minutes |
| Charging Time | 4 Hours |
| Power (W) | 2200-2599W |
| Voltage | 100-240V |
| Motor Type | Brushless Motor |
| Suction Power (Airwatts) | 181-200AW |
| Suction | 22000Pa |
| Filter Type | HEPA |
| Bag Or Bagless | Bagless |
| LCD Display | Yes |
| App-Controlled | No |
| Product Net Weight | 1-2Kg |
| Cleaning Area | 80-150㎡ |
| Certification | CE |
User Tips
- For optimal cleaning, ensure the clean water tank is filled and the dirty water tank is emptied before each use.
- Take advantage of the smart dirt detection feature by allowing the vacuum to adjust its power automatically for different cleaning needs.
- Regularly check and clean the HEPA filter to maintain strong suction and air quality.
- Utilize the self-cleaning function after each significant use to keep the roller brush and internal pipes hygienic and free from odors.
- The device is designed for onsite installation after-sales service, which can be beneficial for complex issues.
Warranty and Support
Your Tineco Floor one 2.0 LED Wet & Dry Wireless Handheld Vacuum Cleaner with Mop comes with a 1-Year Warranty from the date of purchase.
After-sales Service: Onsite installation support is provided for this product. For warranty claims, technical assistance, or service inquiries, please contact your retailer or the manufacturer's customer support. Keep your proof of purchase for warranty validation.
Frequently Asked Questions (FAQ)
- Q: Which category does it belong to?
- A: It belongs to the cordless handheld vacuum cleaner category.
- Q: How long does the battery last?
- A: The battery life of this product is between 30-59 minutes.
- Q: How much power does it consume?
- A: It consumes power in the range of 2200-2599W.
- Q: Can you tell me about its type?
- A: It is a cordless handheld vacuum cleaner.
- Q: What are the notable features of this product?
- A: Some of the notable features include onsite installation service, a brushless motor, and a working time of 30-60 minutes. Please note that this model is not app-controlled.
- Q: What's the model number of this product?
- A: The model number of it is Tineco Floor one 2.0 LCD.