1. Safety Information
- Ensure the power supply voltage matches the LED strip's voltage (12V strip for 12V supply, 24V strip for 24V supply). Connecting incorrect voltage will damage the strip.
- Do not connect the LED strip directly to AC power. A suitable DC power adapter is required.
- Avoid bending the strip sharply or at angles less than 90 degrees to prevent damage to the internal circuitry.
- Do not operate the LED strip while it is still wound on the reel, as this can cause overheating. Unroll completely before use.
- Keep away from water and moisture unless the product is specifically rated for outdoor or waterproof use (this product is IP20, not waterproof).
- Disconnect power before any installation, maintenance, or troubleshooting.
2. Product Overview
The Veromount COB LED Strip Light offers versatile and vibrant lighting solutions for various applications. Featuring Chip-on-Board (COB) technology, these strips provide a uniform, dot-free illumination without dark areas. Available in multiple configurations including RGB, RGBW, RGBCCT, and SPI (individually addressable) versions, they offer a wide range of colors and effects.
Key features include:
- COB Technology: Provides continuous, uniform light without visible LED dots.
- Color Options: RGB (Red, Green, Blue), RGBW (RGB + White), RGBCCT (RGB + Correlated Color Temperature adjustable white), and SPI (individually addressable for dynamic effects).
- High LED Density: Available in 576, 720, 784, and 840 LEDs per meter for bright and smooth lighting.
- Flexible Design: Can be bent and shaped to fit various surfaces.
- Cuttable: Can be cut at designated marks to achieve desired lengths.
- Adhesive Backing: Equipped with double-sided tape for easy installation.
3. Specifications
Below are the detailed specifications for various models of the Veromount COB LED Strip Lights:
RGB 576LEDs COB LED Strip
| Feature | Specification |
|---|---|
| Input Voltage | DC12V/24V |
| Wattage | 10-12W/M |
| FPCB Width | 10mm |
| LED Quantity | 576LEDs/M |
| Cutting Length | 31mm (12V), 62mm (24V) |
| Color Temperature | RGB |
| Color Rendering Index (CRI) | Ra＞90 |
| Operation Temperature | -20℃ to +45℃ |
| Storage Temperature | -20℃ to +60℃ |
| View Angle | 180° |
| Energy Grade | A+ |
| Working Hour Lifetime | 50,000hrs for Tc<70°C |
| Waterproof Rate | IP30 |
RGB 840LEDs COB LED Strip
| Feature | Specification |
|---|---|
| Input Voltage | DC12V/24V |
| Wattage | 12-16W/m |
| FPCB Width | 12mm |
| LED Quantity | 810/840 LEDs/M |
| Color Temperature | RGB |
| Color Rendering Index (CRI) | Ra＞90 |
| Operation Temperature | -20℃ to +45℃ |
| Storage Temperature | -20℃ to +60℃ |
| View Angle | 180° |
| Working Hour Lifetime | 50,000hrs for Tc<70°C |
| Waterproof Rate | IP20 |
RGBWW/RGBW 784LEDs COB LED Strip
| Feature | Specification |
|---|---|
| Input Voltage | DC24V |
| Wattage | 13-16W/M |
| FPCB Width | 12mm |
| LED Quantity | 784LEDs/M |
| Cutting Length | 25mm |
| Color Temperature | RGBWW/RGBW |
| Color Rendering Index (CRI) | Ra＞90 |
| Operation Temperature | -20℃ to +45℃ |
| Storage Temperature | -20℃ to +60℃ |
| View Angle | 180° |
| Energy Grade | A+ |
| Working Hour Lifetime | 50,000hrs for Tc<70°C |
| Waterproof Rate | IP20 |
RGBCCT 840LEDs COB LED Strip
| Feature | Specification |
|---|---|
| Input Voltage | DC24V |
| Wattage | 16-18W/m |
| FPCB Width | 12mm |
| LED Quantity | 840 LEDs/M |
| Cutting Length | Every 35mm |
| Color Temperature | RGBCCT |
| Individually Addressable | Every 35mm can be uniquely controlled |
| Color Rendering Index (CRI) | Ra＞90 |
| Operation Temperature | -20℃ to +45℃ |
| Storage Temperature | -20℃ to +60℃ |
| View Angle | 180° |
| Working Hour Lifetime | 50,000hrs for Tc<70°C |
WS2811 RGB 576LEDs COB LED Strip
| Feature | Specification |
|---|---|
| Input Voltage | DC12V/24V |
| Pixels | 16 pixels/meter |
| Power | 12-16W/m (24V), 8-10W/m (12V) |
| FPCB Width | 10mm |
| LED Quantity | 576LEDs/M |
| Cutting Length | 62mm |
| Color | RGB full color |
| Color Rendering Index (CRI) | Ra＞90 |
| Operation Temperature | -20℃ to +45℃ |
| Storage Temperature | -20℃ to +60℃ |
| View Angle | 180° |
| Energy Grade | A+ |
| Working Hour Lifetime | 50,000hrs for Tc<70°C |
| Waterproof Rate | IP20 |
WS2811 RGB 720LEDs COB LED Strip
| Feature | Specification |
|---|---|
| Input Voltage | DC12V/24V |
| Wattage | 16-20W/m (24V), 8-12W/m (12V) |
| Pixels | 20 pixels/meter |
| FPCB Width | 10mm/12mm |
| LED Quantity | 720LEDs/M |
| Cutting Length | 50mm |
| Color Temperature | RGB full color |
| Color Rendering Index (CRI) | Ra＞90 |
| Operation Temperature | -20℃ to +45℃ |
| Storage Temperature | -20℃ to +60℃ |
| View Angle | 180° |
| Energy Grade | A+ |
| Working Hour Lifetime | 50,000hrs for Tc<70°C |
| Waterproof Rate | IP21 |
4. Setup and Installation
4.1 Unpacking and Inspection
- Carefully unroll the LED strip from its packaging.
- Inspect the strip for any visible damage.
- Confirm you have the correct voltage (12V or 24V) and type (RGB, RGBW, RGBCCT, SPI) of LED strip as ordered.
- Note: The package includes the LED strip only. Power supply, controller, and connectors are NOT included and must be purchased separately.
4.2 Surface Preparation
- Ensure the installation surface is clean, dry, and smooth. Dust, oil, or uneven surfaces can affect the adhesive's performance.
- For optimal adhesion, clean the surface with isopropyl alcohol and let it dry completely.
4.3 Cutting the LED Strip
- The LED strip can be cut to your desired length only at the designated cutting marks. These marks are typically indicated by a copper pad and a scissor icon.
- Cutting at any other point will damage the circuit and render that section of the strip unusable.
4.4 Wiring and Connection
The connection method depends on the type of LED strip (RGB, RGBW, RGBCCT, or SPI) and the controller/power supply used. Always ensure correct polarity and voltage.
General Connection Steps:
- Connect the LED strip to a compatible LED controller. The number of pins on the strip (e.g., 4-pin for RGB, 5-pin for RGBW/RGBCCT, 3-pin for SPI) must match the controller's output.
- Connect the LED controller to a suitable DC power supply (12V or 24V, matching the strip's voltage).
- Connect the DC power supply to an AC 100V-220V power source.
Wiring Diagrams:
Refer to the following diagrams for specific wiring configurations:
4.5 Mounting the LED Strip
- Peel off the protective backing from the double-sided adhesive tape on the back of the LED strip.
- Carefully press the strip onto the prepared surface, ensuring firm and even contact along its entire length.
- The strip's flexibility allows for installation around curves and corners.
5. Operation
Once properly installed and connected to a compatible controller and power supply, operate your LED strip as follows:
- Power On/Off: Use the power button on your LED controller or power supply to turn the lights on or off.
- Color Selection: For RGB, RGBW, and RGBCCT strips, use your controller to select desired colors, adjust brightness, and choose dynamic modes.
- Brightness Adjustment: Most controllers allow dimming to achieve the desired light intensity.
- Dynamic Effects (SPI/Addressable Strips): For WS2811 (SPI) strips, a programmable controller is required to create complex lighting patterns and effects, as each segment can be controlled individually.
6. Maintenance
- Cleaning: Gently wipe the surface of the LED strip with a soft, dry cloth to remove dust. Do not use abrasive cleaners or excessive moisture. Ensure power is disconnected before cleaning.
- Inspection: Periodically check connections for any loose wires or signs of wear.
- Heat Management: Ensure the LED strip is installed in a location with adequate airflow to prevent overheating, which can shorten its lifespan.
7. Troubleshooting
- Strip not lighting up:
- Check if the power supply is correctly connected and receiving power.
- Verify that the LED strip's voltage matches the power supply's output voltage.
- Ensure all connections between the strip, controller, and power supply are secure and have correct polarity.
- If using a controller, ensure it is functioning correctly.
- Incorrect colors or flickering:
- Check the connections to the controller; ensure RGB/RGBW/RGBCCT pins are correctly aligned.
- For SPI strips, ensure the data input is correctly connected and the controller is programmed for the correct chip type (e.g., WS2811) and pixel count.
- Ensure the power supply is sufficient for the length of the strip. Voltage drop can cause color inconsistencies.
- Sections of the strip not working:
- Inspect the strip for physical damage or improper cuts.
- Note that soldering is a normal part of electronic product manufacturing and does not indicate a quality problem unless it affects functionality.
8. User Tips
- Voltage Matching is Critical: Always double-check that your LED strip's voltage (12V or 24V) precisely matches the output voltage of your power supply. Mismatching voltages will cause irreversible damage to the strip.
- Test Before Final Installation: Before peeling off the adhesive and permanently mounting the strip, connect it to your power supply and controller to ensure all segments light up and function as expected.
- Consider Aluminum Channels: For a professional finish and improved heat dissipation, consider installing your LED strips in aluminum channels. This can extend the lifespan of the LEDs.
- Plan Your Cuts: Carefully measure and plan where you will cut the strip. Only cut at the designated marks to avoid damaging the circuit.
9. Warranty and Support
For any product-related inquiries, technical support, or warranty claims, please contact the seller directly through the platform where you made your purchase. Provide your order details and a clear description of the issue to facilitate a quicker resolution.
