BAOFENG UV-5Rmini

Contents

BAOFENG UV-5Rmini Two-Way Radio User Manual

Comprehensive guide for setup, operation, and maintenance of your UV-5Rmini radio.

1. Introduction

Thank you for purchasing the BAOFENG UV-5Rmini two-way radio. This dual-band, dual-display, and dual-watch radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation of your device.

This manual covers the UV-5Rmini Series Amateur Radio. A PDF version of this manual is available for download from the manufacturer's website.

BAOFENG UV-5Rmini radio with 1.44 inch TFT screen, 999 channel storage, Bluetooth read, dual display, dual frequency support, and dual PTT key design.

Figure 1: BAOFENG UV-5Rmini Two-Way Radio

2. Safety Warnings and Regulations

2.1. General Safety Information

WARNING!

  • European Users: Operation of this unit in Transmit mode requires a valid Amateur Radio License. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU.
  • PMR446, FRS, GMRS, MURS: There are restrictions on these bands that make this transceiver illegal for use.

ATTENTION!

  • When programming the radio, always read the factory software data first, then rewrite with your frequency. Use a programming cable with a PC for authorized frequency, bandwidth, and power settings. Ensure your programming complies with FCC (or EU other country) license certification.
  • Before using this product, read the RF Energy Exposure and Product Safety Guide for safe usage and RF energy awareness.

2.2. Regulatory Conformance

EU Regulatory Conformance

The product complies with essential requirements and relevant provisions of Directive 1999/5/EC (2014/53/EU), 2006/66/EC, 2011/65/EU, and 2012/19/EU. This information applies to EU countries only.

FCC Part 15 / IC Compliance

This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standards. Operation is subject to the following conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the responsible party could void your authority to operate the equipment.

2.3. FCC RF Exposure

WARNING!

  • Do not use the radio with a damaged antenna. Contact your local dealer for a replacement.
  • Hand-Held Operation (Held-to-Face): Hold the radio 1 inch (2.5 cm) from your face to comply with FCC RF exposure requirements.
  • Body-Worn Operation: Use the supplied belt-clip accessory. Third-party accessories should be avoided unless approved by the manufacturer.

2.4. Precautions for Portable Terminals

Operating Prohibitions

  • Do not operate in locations with fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not operate near any blasting area.
  • Do not operate near medical or electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate in areas where wireless communication equipment is prohibited.

Important Tips

  • Do not use unauthorized or damaged accessories.
  • Keep the product at least 2.5 centimeters away from your body during transmission.
  • Avoid prolonged reception at high volume.
  • In vehicles with airbags, do not place the product over or in the airbag deployment area.
  • Keep the product and its accessories out of reach of children and pets.

2.5. Precautions for Batteries

Charging Prohibitions

  • Do not charge or replace batteries in locations with fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not charge a wet battery; dry it with a soft, clean cloth first.
  • Do not charge a battery that is deformed, leaking, or overheating.
  • Do not charge with an unauthorized charger.
  • Do not charge in locations with strong radiation.
  • Avoid overcharging, as it shortens battery life.

Maintenance Instructions

  • Clean accumulated dust on the charging connector regularly with a clean, dry cloth.
  • Charge the battery between 5°C and 40°C. Outside this range, battery life may reduce or leakage may occur.
  • When charging a battery attached to the product, turn the radio off for a full charge.
  • Do not remove the battery or unplug the power cord during charging.
  • Do not dispose of the battery in fire.
  • Do not expose the battery to direct sunlight or other heat sources.
  • Do not squeeze, penetrate, or remove the battery housing.

3. Product Features

  • Multi-Band Reception: 6-band scan receiver (FM 78-108MHz; AM 108-136MHz; VHF 136-174MHz; UHF 400-520MHz, 350-390MHz).
  • Dual-Band Transmission: VHF 144-148MHz; UHF 420-450MHz.
  • Output Power: 5W/2W RF output, dual PTT transmitter.
  • Display: 1.44" TFT large screen with full keyboard.
  • Channel Management: 999 channel memory, local channel storage and deletion, full keyboard manual frequency input.
  • Frequency Pairing: One-click frequency pairing for easy grouping.
  • Bluetooth Programming: Wireless read/write frequency via dedicated APP.
  • Relay Function Settings: Frequency difference, frequency difference direction, relay activation audio settings.
  • Security Features: Alarm function (three types of alarm settings).
  • Channel Editing: Built-in input method for local editing of channel name, receiving frequency, and transmitting frequency.
  • DTMF: DTMF encoding and decoding functions, 20 DTMF calls.
  • Frequency Hopping Function.
  • Customizable Side Buttons: Functions include radio, scan, sweep, voice control, flashlight, alarm.
  • FM Radio: Receive frequency 78-108MHz.
  • Keypad Lock: Automatic or manual keypad lock.
  • Backlight Selection.
  • Charging: Supports Type-C charging and charging dock.
Icons representing key features: Mini Case, Bluetooth read-write frequency, Dual PTT key design, 999 channels, One-Touch Frequency Pairing, Multi-segment scanning reception, Adjustable high and low power, Radio function, Type-C charging.

Figure 2: Key Features Overview

4. Package Contents

The standard package includes the following items:

ItemQuantity (PCS)ItemQuantity (PCS)
Radio1Lanyard1
Battery1Operation Manual1
Antenna1Belt Clip1

*Charger and power adapter are subject to the final configuration of the dealer. Charging instructions in this manual may not be appropriate if Type-C charging method is used.

Contents of the BAOFENG UV-5Rmini package including the radio, battery, antenna, lanyard, USB-C charging cable, and belt clip.

Figure 3: Standard Package Contents

5. Product Overview

Diagram of the BAOFENG UV-5Rmini radio with numbered parts indicating antenna, SK1 button, PTT-A, OK/Menu, V/M-VFO/MR, PTT-B, Numeric Keypad, Flashlight, Volume/Power Knob, Screen, Accessory Port, Cancel/Back, Up/Down buttons, A/B, Microphone, LED Indicator, Battery Latch, Type-C Charging indicator light, Type-C Charging Port, Search/Flashlight button.

Figure 4: BAOFENG UV-5Rmini Product Diagram

5.1. Parts Description

  1. Antenna
  2. SK1-Customized Function Keys/Monitor button
  3. PTT-A Button
  4. OK/Menu button
  5. V/M-VFO/MR
  6. PTT-B Button
  7. Numeric Keypad
  8. Flashlight
  9. Volume/Power Knob
  10. Screen
  11. Accessory Port
  12. Cancel/Back button
  13. ▲ Up button/▼Down button
  14. A/B
  15. Microphone
  16. LED Indicator
  17. Battery Latch
  18. Type-C Charging indicator light
  19. Type-C Charging Port
  20. Search/Flashlight button

5.2. LCD Display Icons

IconDescription
RSSISquelch Open/Close Indicator
H/LTransmit power level indicator, According to Power
DMake sure you can hear the DTMF side tone from the radio speaker, set to DT-ST, ANI-ST, DT+ANI.
(C)CTCSS enabled
+Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX.
-Enables access of repeaters in VFO/Frequency Mode. TX will be shifted lower in frequency than RX.
DDual watch enabled
A lock iconKeypad lock enabled
VVOX enabled
A person iconThe confidential calling feature is activated
NNarrowband enabled
Battery iconBattery level indicator
RReverse function enabled
TThe terminal is switched from transit mode to pass-through mode.
SCRThe voice scramble function has been activated

6. Setup and Basic Operations

6.1. Attaching the Antenna

Turn the antenna clockwise until it is tight. To remove, turn it counterclockwise.

6.2. Turning Your Radio On and Off

  • To turn ON: Turn the [Volume/Power] rotary knob clockwise.
  • To turn OFF: Turn the [Volume/Power] rotary knob counterclockwise.

6.3. Setting the Volume

  • Increase volume: Turn the [Volume/Power] rotary knob clockwise.
  • Decrease volume: Turn the [Volume/Power] rotary knob counterclockwise.

CAUTION:

  • Do not hold the radio close to your ear if the volume is set to an uncomfortable level, as it could cause hearing damage.
  • Do not hold the radio antenna in your hand or shake the radio by the antenna, as this will reduce performance and life of the antenna.

6.4. Locking or Unlocking Keypad

To prevent accidental changes to radio settings:

  • To lock: Press and hold the [*] key until the screen displays the "lock" icon.
  • In lock mode: You can still turn the intercom on/off, adjust volume, receive/transmit, send call tones/emergency alerts, and listen to channels. All other functions are locked.
  • To unlock: Press and hold the [*] key again until the "lock" icon disappears.

7. Advanced Operations and Menu Functions

7.1. Keypad Entry

Use the numeric keypad to enter radio aliases, channel aliases, numbers, etc.

  • To switch input methods: Press [# ↑ ] key.
  • To enter a special character: Press 1 (outside numeric input mode).
  • To enter a space: Press 0 (outside numeric input mode).

7.2. Channel Selection and Memory

  • Select a Channel: Press [V/M] to toggle between VFO (Frequency) and Channel mode. Use ▲/▼ buttons or the rotary encoder to select the desired channel. Enter 3-digit channel numbers (e.g., 064 for channel 64).
  • Channel Memory: In Frequency and Standby mode, store frequencies and parameters.
    1. Press [MENU] [3] [MENU] [1] [5]. Screen displays “MEMCH”.
    2. Press [MENU] to enter. Use ▲/▼ to select channel.
    3. Press [MENU] to store. A sound confirms success.
    4. Press [EXIT] to return to standby.

    NOTE: Set CTCSS tones, DCS codes, or frequency offset before storing the channel. Stored channels display as CH-.

  • Delete a Channel (DEL-CH): In VFO and Standby mode:
    1. Press [MENU] [3] [MENU] [1] [6]. Screen displays “DELCH”.
    2. Press [MENU] to enter. Use ▲/▼ or rotary encoder to select channel.
    3. Press [MENU] to confirm deletion.
    4. Press [EXIT] to return to standby.

    NOTE: Channel 1 cannot be deleted.

7.3. Band and Frequency Switching

  • Main Band/Sub Band Switch: In standby, press [A/B] to toggle between A and B bands. The highlighted band is the main band.
  • VFO/Channel Switch: Press [V/M] to switch between VFO (Frequency) and Channel display. VFO mode shows 'VFO' icon; MR mode shows channel serial number.
  • Setting the VFO Frequency: Turn radio to VFO mode, press [A/B] for main channel.
    • Input VFO frequency directly with keypad.
    • Press ▲/▼ or rotary encoder to adjust VFO frequency.

7.4. Communication Functions

  • Call Service: All radios in a group must be on the same channel and sub-code. Keep microphone 2.5-5 cm from mouth when transmitting.
    • Initiate a call: Select channel, press and hold [PTT-A] (upper screen) or [PTT-B] (lower screen). Red indicator light is on. Speak into microphone.
    • Receive a call: After releasing [PTT], radio is in receivable state. Green indicator light is on when receiving.
  • Emergency Alarm: Press the preset [SOS] key to enable/disable emergency alarm.
  • FM Radio Function: Set [SK1] key to radio function via Menu >> Radio Set. Press [SK1] to enter radio mode.
    • Press ▲/▼ to search channels.
    • Press [# ↑ ] to auto-search (displays 'SEEK...').
    • Press [EXIT] to switch frequency band (65.0/75.0MHz).
    • Press [SK1] to exit radio mode.
  • Monitor: Press and hold pre-programmed [Monitor] key to enter monitor mode for weak signals or volume check. Release to exit.
  • Frequency Search: Press pre-programmed [SEARCH] key or press and hold "magnifying glass" key. Screen displays "SEARCH...". Press [# ↑ ] to switch searching band (VHF/UHF). Frequency and CTCSS/DCS code displayed after search. Press [MENU] to save.
  • Reverse Frequency Function: Short press [*] in relay mode to invert receive/transmit frequency. Screen shows 'R' icon. Used for repeaters with frequency difference.
  • Talk Around Function: In repeater mode, press [*] to switch between Talkaround and Repeater Mode. Screen displays 'T' or 'R' icon. In Talkaround mode, receive frequency equals transmit frequency.
  • Repeater Activation Tone: Press and hold [PTT], then [SK1] to transmit 1750Hz audio to activate a repeater.
  • Voice-activated transmit (VOX): Enables hands-free transmission.
    1. In Standby, press [MENU][2][MENU][4] for Vox Switch.
    2. Press [MENU][2][MENU][5] for Vox Level. Use ▲/▼ to select level (1-9). Lower value = higher sensitivity. 'V' icon displays.
    3. Press [MENU] to save.
    4. To turn off, select OFF.
  • Dual Watch: Radio receives on channel A or B.
    1. Press [MENU] [2] for Radio Set.
    2. Press [MENU] + ▲/▼ to select "15 Dual Watch".
    3. Press [MENU] to enter. Use ▲/▼ to select "On".
    4. Press [MENU] to save. 'D' icon displays. Repeat to select "Off" to disable.
  • Stopwatch Function:
    • Press and hold [MENU] to enable.
    • Press [MENU] to start/stop.
    • Press [EXIT] to exit.
  • Weather Radio/Scan Weather Channel: Receives NOAA weather reports.
    • Turn on: Press and hold [0] for 3 seconds. "cloud" icon appears. Radio goes to Weather band mode.
    • Auto-scan: Press and hold [# ↑ ] for 3 seconds to scan all 10 NOAA channels.
    • Manual select: After scanning, use ▲/▼ to select channel.
    • Exit: Press "cloud" key or [PTT].

    NOTE: Weather Channels Wx 1 Thru 10 are Receive-only for NOAA and Canadian broadcasts. You cannot transmit on these channels.

    Weather Channel Frequencies

    Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
    CH-01162.550CH-06162.500
    CH-02162.400CH-07162.525
    CH-03162.475CH-08161.650
    CH-04162.425CH-09161.775
    CH-05162.450CH-10163.275

7.5. Wireless Program Radio

The radio can be programmed wirelessly using a dedicated APP. Download the APP by scanning the QR codes below:

QR code for Android App

Android App

QR code for iOS App

iOS App

Programming Steps:

  1. Press [MENU] + [4] to enter Wireless CPS.
  2. Press [MENU] + ▲/▼ to select "On". The "Bluetooth" icon will display on the screen.
  3. On your Android phone, download and install the radio APP.
  4. Open the APP, allow Bluetooth and location functions.
  5. Select the walkie-talkie model (5Rmini Series), connect the radio.
  6. Click "Walkie-talkie" in the app. A connection success prompt will appear, and you can return to the home page.

Once connected, you can:

  • Read the radio data: After reading frequencies, enter program details to configure channel information, frequency mode, and optional functions.
  • Save Profile: Save the programmed profile as a new profile.
  • Write data to radio: From the home page, select program, click 'Write' to transfer frequencies. The radio will restart automatically.

8. Technical Specifications

Technical Specification summary for BAOFENG UV-5Rmini, showing dimensions, multi-segment scanning, dual-band transmission, 1.44 inch TFT screen, 999 channel storage, Bluetooth programming, dual PTT, FM radio, Type-C charging.

Figure 5: Technical Specifications Overview

General
Product Model5R Mini
Channel Capacity999
Receiver FrequencyFM 76-108 MHz; VHF 136-174MHz, UHF 400-520MHz, 350-390MHz
Transmission FrequencyVHF 144-148MHz, UHF 420-450MHz
Channel Spacing25.0KHz (Wide) / 12.5KHz (Narrow)
Memory Channel999 Groups
Operation VoltageDC 7.4 V ±10%
Dimensions52(w) x 107(h) x 37(d) mm (Without antenna)
WeightAbout 200g (Including antenna and battery)
MaterialPlastic + metal
Waterproof / Water-ResistantIP55
CertificationCE, FCC
Transmitter Specification
Transmission Current≤1600mA
Output Power (w)3w-5w
Modulation Mode16KΦF3E / 11KΦF3E
Maximum Frequency Offset (Broadband/Narrowband)<5KHz / <2.5KHz
Signal-to-Noise Ratio (Broadband/Narrowband)≥-45dB / ≥-40dB
Receiver Specification
Receiving Sensitivity≤0.25μV (12dB SINAD)
Rated Audio Power Output1W @16 ohms
Receive Current≤380mA
Signal-to-Noise Ratio≥45dB
Spurious Response Suppression70dB
Connection for Accessories2 pin Kenwood jack
Antenna Impedance50 Ohm

NOTE: All specifications may be modified without prior notice or liability.

9. User Tips

  • Communication Range: The effective communication distance can vary significantly based on terrain, obstacles, weather conditions, and power output settings. In open areas with clear line of sight, the range will be maximized. In urban or heavily forested areas, the range will be reduced.
  • Bluetooth Programming: For easier frequency management, utilize the Bluetooth programming feature with the dedicated Baofeng Radio APP. This simplifies the process compared to manual input.
  • Battery Life: To maximize battery life, ensure the radio is turned off during charging and avoid overcharging. Operating within the recommended temperature range (5°C~40°C) also helps prolong battery health.

10. Maintenance and Warranty

10.1. General Maintenance

Your Two-Way Radio is a precision electronic product and should be handled with care. To ensure longevity and maintain warranty:

  • Do not attempt to open the radio. Precision mechanics and electronics require specialized equipment. Unauthorized opening voids the warranty.
  • Avoid storing the radio in direct sunlight or hot areas, as high temperatures can shorten device life and warp plastics.
  • Keep the radio dry. Rainwater or dampness can corrode electronic circuits.
  • If the radio emits a peculiar smell or smoke, immediately shut off power and remove the battery.
  • Do not transmit without an antenna.

10.2. Transportation Instructions

  • Damaged batteries must not be transported.
  • To avoid short circuits, separate batteries from metal parts or each other if transporting multiple batteries.
  • The radio must be switched off and secured against accidental activation if the battery is attached during transport.
  • The content of the shipment must be declared in shipping documents with a Battery Shipping Label. Contact your carrier for local regulations.

10.3. Warranty Information

A 12-month warranty is offered for the machine, and 6 months for accessories, starting from the date of goods receipt.

The seller tests every unit before shipping. If a defective unit is received, contact the seller within 3 days of parcel receipt for a replacement.

If the item is defective within 30 days of receiving, the seller will bear one-way shipping for warranty. If defective after 30 days, buyers are responsible for all extra shipping fees.

All returned items must be in original condition, including box, packaging, and all other accessories. Returns by post air mail should declare "sample" with a value of "US$10.00".

Service Policy image detailing 12-month warranty for machine, 6-month for accessories, 3-day contact for replacement, 30-day shipping fee coverage, and return policy requirements.

Figure 6: Warranty and Service Policy

11. Product Demonstration Video

Video 1: BAOFENG UV-5Rmini Product Overview and Basic Operation Demonstration.

12. Disclaimer and Certifications

The accuracy and completeness of the contents of this manual are diligently compiled. However, we do not bear responsibility for possible errors or omissions. Due to continuous technological development, we reserve the right to change the design and specifications of the product without prior notice. No part of this handbook may be copied, modified, translated, or disseminated without prior written authorization.

This product is certified with CE and FCC standards. It also complies with WEEE (Waste Electrical and Electronic Equipment) directives for proper disposal and recycling.

Please refer to the official documentation for full details on certifications.

Print version: 5R Mini_V1.0

© 2023 BAOFENG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.