1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your hiwheel KCQ8.5 Inch with APP Plus Scooter Controller. This controller is designed for 8.5-inch electric scooters and features Bluetooth connectivity for app control, offering enhanced functionality and customization. Please read this manual thoroughly before use to ensure safe and optimal performance.
2. Safety Information
⚠️ Please be aware of potential fire risks and strictly follow the instruction manual for charging and storage of your scooter's battery and related components.
3. Package Contents
Verify that all items listed below are included in your package. If any items are missing or damaged, please contact customer support.
- Kechuangqi Scooter Controller Unit
- Display Unit
- Accelerator
- Headlight
- Taillight
- Brake Lever
- Wiring Harnesses (for motor, Hall sensor, display, taillight, and battery XT60 connector)
- QR Code for APP download


4. Specifications
| Attribute | Value |
|---|---|
| Model Number | KCQ8.5 Inch with APP Plus |
| Type | Controller |
| Brand Name | hiwheel |
| Voltage | DC36V |
| Rated Power | 350W |
| Undervoltage Protection | 30V |
| Current Limit | 15A ± 2A (Upgraded from 13A for more power) |
| Max Speed | 30 km/h |
| Compatibility | 8.5 inch scooters (FOSTON, X-Play, DIGMA, etc.) |
| Features | Bluetooth APP control, Scooter Controller, Electric Overboard, 36V Electric Scooter Control Unit |
5. Setup and Installation
Before beginning installation, ensure your scooter is powered off and the battery is disconnected. It is recommended to compare your existing controller's interface with the provided components to ensure compatibility.
5.1 Wiring the Controller Unit
The main controller unit connects to various components of your scooter. Refer to the diagram below for proper connections.

5.2 Wiring the Display Unit
The display unit connects to the accelerator, headlight, and brake. Ensure these connections are secure.

5.3 Motor Wiring Adjustment (Advanced)
If you experience issues with motor operation (e.g., noise, vibration without running, or running in reverse), you may need to adjust the motor's Hall lines or phase lines. This is an advanced procedure and should be performed carefully.

5.4 Physical Installation
Once all wiring connections are made, carefully place the controller and associated wiring into the scooter's deck. Ensure all connections are secure and no wires are pinched or exposed.


6. Operating Instructions
6.1 Basic Functions
- Boot: Long press the power button (approximately 1 second). The buzzer will sound twice.
- Shutdown: Press and hold the power button for 3 seconds. The buzzer will sound twice.
- Lights: In the power-on state, short press the power button (within 1 second) once to turn on the front and rear lights. Headlights will be steady on, and taillights will flash.
- Brake: The scooter features electronic brakes combined with disc brakes. When braking, the taillight will illuminate steadily.
- Gear Shift: In the power-on state, the scooter defaults to low-speed gear. Press the power button twice quickly (within one second) to switch between gears. A green indicator signifies low gear, and a red indicator signifies high gear.
- Battery Display: The display unit shows battery level based on voltage:
- 33V-36V: First light is on.
- 36V-37V: One or two lights are on.
- 37V-38.5V: One or two lights are on.
- 38.5V or more: All four lights are on.
- Low Voltage Alarm: If the battery voltage drops below 33V, the first battery light will flash, and the buzzer will sound 6 times.
- Low Voltage Alarm Speed Mode: When the low voltage alarm is active, the speed limit is approximately 15 km/h. To release the low voltage mode and return to normal operation, the throttle must be returned to its initial (zero) position once the power returns to 37V or above.
- Constant Speed Cruise: Maintain a stable speed for approximately 6 seconds to automatically activate cruise control. Once cruise control is fixed, you can release the throttle. To deactivate cruise control, press the brake or push the throttle again.
- Speed: The low-speed gear operates at 15 ± 2 km/h, and the high-speed gear operates at 25 ± 2 km/h.
- Automatic Shutdown: The scooter will automatically shut down after 10 minutes of no operation.
6.2 APP Control
This controller supports app connectivity via Bluetooth, allowing you to monitor and adjust various settings of your scooter. Scan the QR code provided with your kit to download the companion app.

6.2.1 App Interface and Language
The app interface allows for speed control (1st, 2nd, 3rd gear) and displays riding time, mileage, and total mileage. The app is designed to adapt to your mobile phone's system language.

6.2.2 App Settings
Within the app's settings, you can configure various parameters, including:
- Start mode: Choose between 'Zero start' (no initial speed needed to start) and 'Non-zero start' (requires a kick-off).
- Unit setting: Switch between mph and km/h.
- Fixed speed cruise: Enable or disable.
- Connection password: Set a password for Bluetooth connection.

7. Maintenance
- Regularly check all wiring connections for looseness or damage.
- Keep the controller unit clean and dry. Avoid water ingress, as this can damage internal components.
- Inspect the motor phase and Hall lines periodically for any signs of wear or damage.
- Ensure the brake lever and accelerator return to their initial positions freely.
- Keep the scooter's battery charged according to manufacturer guidelines to prevent undervoltage issues.
8. Troubleshooting (Error Codes)
The display unit may show error codes to indicate specific issues. Refer to the table below for common error codes and their solutions.
| Error Code | Description | Possible Causes | Solution |
|---|---|---|---|
| E0 | Temperature Protection | Motor temperature exceeds set limit. | Allow the motor to cool down below the set temperature value before resuming operation. |
| E1 | Motor Hall Failure | Motor Hall sensor is damaged or faulty. | Replace the motor. |
| E2 | MOS Tube Failure | Motor phase wires are short-circuited; internal controller components are damaged. | 1. Check motor phase wires for breaks or damage; replace motor if necessary. 2. Replace the controller. |
| E3 | Brake Failure | Brake lever is damaged or not returning to its initial position. | 1. Replace the brake lever. 2. Ensure the brake lever returns freely; if not, replace it. |
| E4 | Accelerator Failure | Speed control handle (accelerator) is damaged or not returning to its initial position. | 1. Replace the speed control handle. 2. Ensure the accelerator returns freely; if not, replace it. |
| E5 | Undervoltage Protection | Supply voltage is below the controller's minimum operating voltage (30V). | Charge or replace the battery. |
| E6 | Controller/Instrument Communication Failure | No communication between the instrument (display) and the controller. | 1. Check communication lines for proper connection. 2. Check motor phase or Hall lines for damage/leakage. 3. Replace the motor. |
| E7 | Overvoltage Protection | Power supply voltage exceeds the controller's maximum voltage; short circuit with Hall wire leading to leakage. | Replace the battery or motor phase wire that matches the controller's voltage. Address any Hall wire short circuits. |
| E8 | Controller Operational Amplifier Failure | Controller damaged due to water ingress or internal component failure. | Replace the controller. |
| E9 | Stalled Rotor Fault | Obstacle preventing motor rotation; incorrect wiring sequence between motor and controller. | 1. Remove any obstacles and loosen the speed control handle. 2. If wiring is incorrect, consult the motor manufacturer for re-matching. |
9. User Tips
- Kick Start vs. Zero Start: If your scooter requires an initial push to start the motor (kick start), you can change this setting in the companion app to 'Zero start' for immediate acceleration from a standstill. This can be found under the 'Start mode' option in the app settings.
- Motor Wiring: Some users have found it necessary to adjust the engine control line positions (green, blue, yellow, black, and red wires) for optimal performance, especially if the motor exhibits unusual behavior. Refer to the detailed motor wiring adjustment section (Figure 5.3) if you encounter such issues.
10. Warranty and Support
The manufacturer provides a service commitment for this product. Please note that warranty typically does not cover water damage or wire damage caused by improper installation or use.
For technical support or warranty claims, please refer to the seller's contact information or the official product page where you made your purchase. Keep your purchase records for any claims.