Introduction
The ID-COOLING IS-50X V3 is a low-profile ITX air-cooling CPU cooler designed for compact systems. It features an ultra-slim design with a 56mm overall height, 5 heat pipes, downward pressing blackened fins, and multi-platform metal fasteners for broad compatibility and efficient heat dissipation.
Specifications
Below are the detailed specifications for the ID-COOLING IS-50X V3 CPU Cooler:
| Feature | Detail |
|---|---|
| Model Number | IS-50X V3 |
| Cooler Type | Low Profile |
| Heatpipes | 5 |
| Supported CPU Sockets | Intel LGA 1150, LGA 1151, LGA 1155, LGA 1156, LGA1200, LGA 1700; AMD Socket AM5, AM4 |
| TDP | 150W |
| Fan Speed | 500 - 2000 RPM ±10% |
| Power Interface | 4-Pin PWM |
| Fan Life | 100,000 hrs |
| Blade Quantity | 9 |
| Bearing Type | Hydraulic Bearing |
| Maximum Airflow | 54.6 CFM |
| Noise Level | 31.2 dB(A) Max. |
| Product Size (L×W×H) | 120 × 120 × 56mm |
| Fan Size (L×W×H) | 120 × 120 × 15mm |
| Product Net Weight | 400g (radiator body + fan) |
| Rated Voltage | 12VDC |
| Rated Current | 0.18A |
| Input Power | 2.16W |
Package Contents
The package should contain the following items:
- ID-COOLING IS-50X V3 CPU Cooler (Heatsink with pre-installed fan)
- Multi-platform mounting hardware (backplates, standoffs, brackets for Intel and AMD sockets)
- Thermal paste
- User Manual (this document)
Installation Guide
Follow these general steps for installing your ID-COOLING IS-50X V3 CPU Cooler. Specific steps may vary slightly depending on your motherboard and CPU socket type. Always refer to your motherboard's manual for precise instructions on CPU cooler installation.
- Prepare Motherboard: Ensure your motherboard is removed from the PC case or has sufficient access for installation.
- Install Backplate: For Intel sockets, attach the appropriate backplate to the rear of the motherboard, aligning the holes with the CPU socket mounting holes. For AMD sockets, the stock backplate is usually retained.
- Attach Standoffs: Screw the correct standoffs into the backplate (or directly into the motherboard for some AMD sockets) from the front side of the motherboard.
- Apply Thermal Paste: Apply a small amount of thermal paste (pea-sized dot or thin line) to the center of your CPU's Integrated Heat Spreader (IHS). Ensure the CPU surface is clean before application. The cooler features precision milling and heat pipe direct touch technology for optimal heat transfer.
- Mount Cooler: Carefully place the IS-50X V3 heatsink onto the CPU, aligning the mounting holes on the cooler's bracket with the standoffs.
- Secure Cooler: Use the provided screws to secure the cooler to the standoffs. Tighten screws in a diagonal pattern (e.g., top-left, bottom-right, top-right, bottom-left) gradually until snug. Do not overtighten.
- Connect Fan Cable: Connect the 4-pin PWM fan cable from the cooler to the CPU_FAN header on your motherboard.
The cooler is designed with memory avoidance features, allowing for good compatibility with memory modules and motherboard I/O components. It supports a memory height of up to 44mm and I/O height of up to 47mm with fan displacement.
Operation
The IS-50X V3 features a 4-pin PWM fan that allows for fine speed regulation. This enables the fan to operate efficiently, providing optimal cooling performance while maintaining low noise levels. The fan speed automatically adjusts between 500 and 2000 RPM based on CPU temperature, controlled by your motherboard's BIOS/UEFI settings or fan control software.
The fan is equipped with 8 rubber dampening pads on both sides to minimize vibration and further reduce operational noise.
Maintenance
Regular maintenance helps ensure optimal performance and longevity of your CPU cooler:
- Dust Removal: Periodically clean the fan blades and heatsink fins to remove accumulated dust. Use compressed air or a soft brush. Ensure the fan is not spinning rapidly when using compressed air to prevent damage to the bearing.
- Thermal Paste: If you remove the cooler for any reason, it is recommended to clean off the old thermal paste from both the CPU and the cooler's base and apply fresh thermal paste before reinstallation.
- Inspection: Occasionally inspect the fan cable for any signs of wear or damage.
The heatsink features electrophoretic blackened fins, providing a long-lasting and elegant finish that is resistant to corrosion.
Troubleshooting
- Fan Not Spinning:
- Check if the 4-pin PWM fan cable is securely connected to the CPU_FAN header on the motherboard.
- Verify fan settings in your motherboard's BIOS/UEFI.
- High CPU Temperatures:
- Ensure the cooler is properly seated and making good contact with the CPU.
- Check if thermal paste was applied correctly and sufficiently.
- Clean any dust accumulation from the heatsink fins and fan blades.
- Verify that the fan is spinning at appropriate speeds.
- Ensure adequate airflow within your PC case.
- Excessive Noise:
- Check for any cables or obstructions hitting the fan blades.
- Ensure the fan is securely mounted and not vibrating excessively.
- Dust accumulation can cause imbalance and noise; clean the fan.
User Tips
- Compatibility Check: Always double-check your motherboard's CPU socket type (e.g., LGA 1150, 1151, 1155, 1156, 1200, 1700, AM4, AM5) against the cooler's supported sockets before installation to ensure proper fit.
- Thermal Paste Application: For best results, use a high-quality thermal paste and ensure an even, thin layer for optimal heat transfer.
- Case Airflow: In ITX builds, good case airflow is crucial. Ensure your case fans are configured to provide sufficient intake and exhaust to support the CPU cooler's performance.
Warranty and Support
ID-COOLING products are manufactured to high-quality standards and are covered by a manufacturer's warranty against defects in materials and workmanship. Please retain your proof of purchase for warranty claims.
For technical support, troubleshooting assistance, or warranty inquiries, please contact ID-COOLING customer service through their official website or authorized distributors.