JAKCOM CDS

Contents

JAKCOM CDS RFID Replicator for R5 Smart Ring Instruction Manual

Model: CDS

1. Product Introduction

The JAKCOM CDS replicator is a specialized reader-writer designed to replicate IC (Integrated Circuit) and ID (Identification) proximity cards into the R5 smart ring. This device allows users to conveniently transfer access card data to their R5 smart ring for various applications.

Note: The JAKCOM CDS replicator is primarily intended for replicating IC/ID access cards. It is not capable of copying financial cards such as bank cards or credit cards.

JAKCOM CDS Replicator and R5 Smart Ring
Image 1: JAKCOM CDS Replicator and R5 Smart Ring.

2. Packing List

Please check the contents of your package to ensure all items are present:

  • CD2 Replicator x 1
  • CD2 Data Cable x 1
  • ID2 Replicator x 1
  • ID2 USB Cable x 1
  • Instruction Book x 1 (English manual)
Contents of the JAKCOM CDS Replicator package
Image 2: Package contents including CD2 Replicator, ID2 Replicator, cables, and manual.

3. Structure Description

Familiarize yourself with the components of the CDS Replicator:

  • IC Card Reading/Writing Area
  • ID Card Reading/Writing Area
  • Indicator Light
  • USB Cable Socket
  • Reading Button
  • Writing Button
  • Power Switch
  • ID Card Reading/Writing Area (on ID2 Replicator)
  • Indicator Light 1 (on ID2 Replicator)
  • Indicator Light 2 (on ID2 Replicator)
  • Charging Socket (on ID2 Replicator)
Diagram showing the components of the CD2 and ID2 Replicators
Image 3: Labeled diagram of the CD2 and ID2 Replicator components.

4. Applicable Card Types

The CDS Replicator supports the following card types:

IC Cards:

Class A and Class B cards with a carrier frequency of 13.56MHz, conforming to ISO-14443 standard. Examples include MIFARE card (Classics, DESFire), M1, S50, UID, CUID, FUID, UFUID, etc.

ID Cards:

Proximity cards with a carrier frequency of 125KHz, conforming to ID standard and containing only the card number. Examples include EM4305, 5200, 8800, T5577, ZX-F08, etc.

Important: Only 125KHz low-frequency HID cards are supported. 13.56MHz high-frequency HID cards are not supported. Please verify your HID type before attempting replication.

Diagram showing IC and ID module locations on the R5 Smart Ring
Image 4: Illustration of No. 1 IC module, No. 1 ID module, and No. 2 ID module on the R5 ring.

5. Operating Instructions

5.1. Replicating an IC Card to the R5 Ring (using CD2 Replicator)

  1. Use the CD2 data cable to connect the CD2 replicator to a computer running a Windows operating system. The indicator light on the replicator will turn red.
  2. Open the newly created "USB disk" drive on your computer.
  3. Double-click to download the operating program in the corresponding language.
  4. Unzip the downloaded file, and then open the operating program.
  5. Place the target IC card on the IC card reading area of the CD2 replicator. The indicator will turn green. Then, click "Start decoding" in the software.
  6. After successful decoding, remove the target IC card and wait for the indicator to turn red again.
  7. Place either the No. 1 or No. 2 IC module of the R5 ring on the IC card reading area. The indicator will turn green.
  8. Click "Write card" in the software. Wait until the card is successfully written. The IC card data is now replicated to your R5 smart ring.
Screenshot of the IC card replication software interface and steps
Image 5: Visual guide for replicating an IC card to the R5 ring.

Video 1: Demonstration of IC card replication process using the CD2 Replicator.

5.2. Replicating an ID Card to No. 1 ID Module of the R5 Ring (using CD2 Replicator)

  1. Connect the CD2 Replicator to your computer as described in step 1 of IC card replication.
  2. Place the target ID card on the ID card reading area of the CD2 replicator. The indicator will turn green.
  3. In the software, navigate to the "LF Card" tab and click "Read".
  4. After successful reading, remove the target ID card and wait for the indicator to turn red.
  5. Place the No. 1 ID module of the R5 ring on the ID card reading area. The indicator will turn green.
  6. Click "Write" in the software. Wait until the card is successfully written. The ID card data is now replicated to the No. 1 ID module of your R5 smart ring.
Screenshot of the ID card replication software interface and steps for No. 1 ID module
Image 6: Visual guide for replicating an ID card to the R5 ring's No. 1 ID module.

5.3. Replicating an ID Card to No. 2 ID Module of the R5 Ring (using ID2 Replicator)

  1. Use the ID2 USB cable to connect the ID2 replicator to a USB power source.
  2. Turn the ID2 replicator switch to "ON". Indicator 1 will turn blue.
  3. Place the target ID card on the ID card reading area of the ID2 replicator.
  4. Press the "R" key to read. If the reading is successful, indicator 2 will turn green.
  5. Place the No. 2 ID module of the R5 ring on the ID card reading area.
  6. Press the "W" key to write. If the writing is successful, indicator 2 will flash and remain green.
  7. If the writing fails, indicator 2 will extinguish. You will need to read the target card again and then retry the writing process.
  8. After use, turn the ID2 replicator switch to "OFF". Indicator 1 will extinguish.
Diagram showing the ID2 Replicator and steps for replicating to No. 2 ID module
Image 7: Visual guide for replicating an ID card to the R5 ring's No. 2 ID module using the ID2 Replicator.

6. Maintenance

  • Keep the replicator and R5 smart ring clean and dry. Avoid exposure to liquids.
  • Store the devices in a cool, dry place away from direct sunlight and extreme temperatures.
  • Handle the devices with care to prevent physical damage.
  • Use only the provided USB cables for connection and power.

7. Troubleshooting (FAQ)

Q: The CD2 replicator connection is unsuccessful.
A: Try using a different computer or replacing the USB cable. Ensure the USB cable is securely connected to both the replicator and the computer.
Q: IC card decoding fails or takes too long (longer than 5 minutes).
A: Increase the "standard" level in the operating program and try decoding again. Confirm that the target IC card is an M1 proximity card. High-capacity cards or CPU cards (e.g., bank cards, bus cards, or other cards involving funds) cannot be decoded by this device. For CPU cards, you can try using the "Card number" button to test if they can be used in non-payment applications like access control or elevators.
Q: The IC card fails to be written into the R5 ring.
A: First, decode the IC module of the R5 ring. Then, click "Format card" in the software to format the IC module. After successful formatting, attempt to replicate the card again.

8. Specifications

ParameterValue
Carrier Frequency13.56MHz, 125KHz
RF Distance1~3cm
Host MaterialABS
Operating Systems (CD2)Windows 7/8/10/11 and Windows Server versions
CD2 Interface TypeType-C
ID2 Interface TypeMicro-USB
ColorBlack

9. User Tips

  • Ensure your computer's USB ports are functioning correctly when connecting the replicator.
  • Always download the latest operating program from the official website for optimal performance and compatibility.
  • When replicating, ensure the target card and the R5 ring module are placed firmly and correctly on the designated reading/writing areas.
  • If you encounter persistent issues, try restarting your computer and the replicator.

10. Warranty and Support

For technical support, warranty information, or any inquiries regarding your JAKCOM CDS RFID Replicator, please use the contact details below:

  • Website: Http://www.JAKCOM.com
  • Email: service@JAKCOM.com
  • Service Phone: +86 400 806 7311, +86 0351-4383818
  • Service Time: 9 am - 9 pm GMT+8
  • Address: 1-102, No. 26, Shuangta East Street, Yingze District, Taiyuan City, Shanxi Province, China
  • Contact: JAKCOM Technology

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.