HORACO SWTGW218AS

Contents

HORACO 2.5GbE Managed Switch

Model: SWTGW218AS

Web Manual Ver. 1.0

1. Introduction

This manual provides detailed instructions for the installation, configuration, operation, and maintenance of the HORACO 2.5GbE Managed Switch (Model: SWTGW218AS). It is intended for network installers and system administrators familiar with network communication and management protocols. The switch is designed to provide high-speed network connectivity with advanced management features.

1.1 Target Audience

This manual is prepared for installers and system administrators responsible for network installation, configuration, and maintenance. Users should have a basic understanding of network communication, management protocols, technical terms, and networking principles.

1.2 Manual Convention

Throughout this manual, specific conventions are used for clarity:

  • GUI Convention: Describes operations and provides necessary information.
  • Notice: Reminds the user of cautions where improper operations could lead to data loss or equipment damage.

2. Product Overview

The HORACO 2.5GbE Managed Switch is a high-performance network device designed to upgrade your network to 2.5G/10G speeds. It features 8x 2.5GbE RJ45 ports and 1x 10GbE SFP+ optical port, offering flexible connectivity and high bandwidth. The switch supports web management for comprehensive configuration, monitoring, and troubleshooting.

HORACO 2.5GbE Managed Switch

Figure 2.1: HORACO 2.5GbE Managed Switch

Video 2.1: HORACO 2.5GbE Managed Switch Product Overview

2.1 Key Features

  • High-Speed Connectivity: 8x 2.5GbE RJ45 ports and 1x 10GbE SFP+ optical port for fast data transfer.
  • Web Management: Supports comprehensive web-based network management functions including VLAN, QoS, Port Aggregation, Mirroring, and DHCP Snooping.
  • Powerful Chip: Built-in high-performance RTL8373N chip for efficient data processing and stable operation.
  • Fanless Design: Adopts an iron shell metal body with heat dissipation holes on both sides for efficient and silent cooling.
  • Robust Protection: Features 4 * 6KV Ethernet Port Lightning Protection.
  • Flexible Installation: Supports desktop placement with non-slip feet and wall mounting.
Key Features Summary

Figure 2.2: Summary of Key Product Features

3. Package Contents

Please check the package contents carefully upon unpacking. If any item is missing or damaged, please contact your vendor.

  • 1 x HORACO 2.5GbE Managed Switch
  • 1 x User Manual
  • 1 x Certificate of Conformity
  • 1 x Power Adapter (EU/US/UK/AU plug type, depending on region)
  • 4 x Non-slip Foot Mats
Packing List and Specifications

Figure 3.1: Packing List and Environmental Specifications

4. Specifications

AttributeValue
Brand NameHORACO
Model NumberSWTGW218AS
Switch TypeEthernet
Number of Interfaces9 (8*2.5G RJ45 ports, 1*10G SFP+ port)
Transmission Rate10/100Mbps/1G/2.5Gbps (RJ45), 10G (SFP+)
Switch Capacity60Gbps
Packet Forwarding Rate44.64Mpps
MAC Address Table4K
Jumbo Frame16Kbytes
Forwarding ModeStore and forward
Communication ModeFull-Duplex & Half-Duplex
VLAN SupportYES (802.1Q)
QoS SupportYES
FunctionQoS, VLAN, Port Aggregation, Mirroring, Flow Control, DHCP Snooping, SNMP
Switch Input VoltageDC 12V 2A
Power ConsumptionMaximum 24W
Product Dimension (L x W x H)160mm x 90mm x 35mm
Net Weight339g
Operating Temperature0~40°C
Storage Temperature-10~70°C
Operating Humidity10%~90%, Non Condensing
Storage Humidity5%~90%, Non Condensing
CertificationsCE, FCC, RoHS
Product Dimensions and Parameters

Figure 4.1: Product Dimensions and Key Parameters

Product Certifications

Figure 4.2: Brand Qualification and Quality Assurance Certifications

5. Setup and Physical Installation

5.1 Physical Installation

The HORACO 2.5GbE Managed Switch offers multiple installation methods to suit your environment:

  • Desktop Placement: Place the switch on a flat surface. Attach the provided non-slip foot mats to the bottom of the device to ensure stability.
  • Wall Mounting: The switch features wall mounting holes on the bottom of its body. Use appropriate screws (not included) to secure the switch to a wall, saving space.
Multiple Installation Methods

Figure 5.1: Desktop Placement and Wall Mounting Options

Wall Mounted Hole Design and DC 12V Power Supply

Figure 5.2: Details of Wall Mounting Hole and DC 12V Power Supply

5.2 Power Connection

Connect the provided DC 12V 2A power adapter to the DC 12V input port on the switch. Ensure the power adapter is securely connected to a power outlet.

5.3 Network Connection

Connect your network devices (computers, routers, NAS, etc.) to the 2.5GbE RJ45 ports using Ethernet cables. For higher bandwidth connections, use the 10G SFP+ port with compatible SFP+ modules and fiber optic cables.

Upgrade to 2.5G/10G Network

Figure 5.3: Network Upgrade with 2.5G RJ45 and 10G SFP+ Ports

6. Web Management Login

To access the switch's web management interface, follow these steps:

  1. Initial PC IP Configuration: For the first login, ensure your PC's IP network segment is consistent with the switch's default IP but with a different IP address. Set your PC's IP address to 192.168.2.x (where x is between 1 and 254, but not 1) and the subnet mask to 255.255.255.0.
  2. Access Web Interface: Open a web browser (Chrome 23.0+, Firefox 20.0+, or superior to IE 9.0) and type the default switch address: http://192.168.2.1 into the address bar, then press 'Enter'.
  3. Login: A login window will appear. Enter the default username admin and the default password admin. Click 'Log in' to access the switch system.
Web Management Interface Login

Figure 6.1: Web Management Login Interface

6.1 Constitution of Client Interface

The typical operation interface provides menu items such as System, Configuration, Security, Monitoring, and Tools. Each item contains submenus for specific settings and information.

Network Management Functions Diagram

Figure 6.2: Overview of Network Management Functions

7. System Settings

7.1 Information

This section displays system information including the device model, MAC address, IP address, netmask, gateway, firmware version, firmware date, and hardware version.

7.2 IP Setting

To change the management IP address of the switch:

  1. Navigate to 'System > IP Setting' in the web interface.
  2. Configure the desired IP Address, Netmask, and Gateway.
  3. Click 'Apply' to save changes.

7.3 User Account

To modify the username and password for web management:

  1. Navigate to 'System > User Account'.
  2. Enter the new username and password, then confirm the new password.
  3. Click 'Apply'.

7.4 Port Setting

This section allows you to query and configure Ethernet ports:

  1. Navigate to 'System > Port Setting'.
  2. You can configure the port's state (Enable/Disable), Speed/Duplex (e.g., 10M/Half, 2.5G/Full), and Flow Control (Off/On).
  3. Click 'Apply' to save changes.

8. Configuration

8.1 VLAN (Virtual Local Area Network)

VLANs allow for logical segmentation of a physical LAN, improving network efficiency and security. This switch supports VLAN types based on 802.1Q, protocols, MAC, and ports.

8.1.1 802.1Q VLAN

To configure 802.1Q VLANs:

  1. Navigate to 'Configuration > VLAN > 802.1Q VLAN'.
  2. You can add/modify VLANs by specifying a VLAN ID (1-4094) and an optional VLAN Name.
  3. Select member ports and designate them as Tagged, Untagged, or Not Member.
  4. Click 'Add/Modify' or 'Delete' as needed.

Notice: VLAN 1 is the system default VLAN and cannot be deleted.

8.1.2 802.1Q VID

To configure Port VLAN ID (PVID) and accepted frame types:

  1. Navigate to 'Configuration > VLAN > 802.1Q VID'.
  2. For each port, set its PVID and the accepted frame type.
  3. Click 'Apply'.

8.2 QoS (Quality of Service)

QoS allows you to prioritize network traffic, ensuring critical applications receive sufficient bandwidth and low latency. This switch supports QoS based on message types and priorities.

8.2.1 Port to Queue

To set processing priorities for different data frame tags:

  1. Navigate to 'Configuration > QOS > Port to Queue'.
  2. Assign a queue (1-8) to each port.
  3. Click 'Apply'.

8.2.2 Queue Weight

To configure the weight for each queue:

  1. Navigate to 'Configuration > QOS > Queue Weight'.
  2. Set the weight for each queue. 'Strict priority' is equivalent to SP, while weights 1-15 are for WRR (Weighted Round Robin) scheduling.
  3. Click 'Apply'.

8.3 Loop Detection/Prevention

The switch can detect network loops by sending and receiving special packets, preventing network instability.

8.3.1 Loop Detection/Loop Prevention

To configure loop detection and prevention:

  1. Navigate to 'Configuration > Loop > Loop Protocol'.
  2. Enable or disable 'Loop Detection' and 'Loop Prevention'.
  3. Configure 'Time Interval' and 'Recover Time' as needed.
  4. Click 'Apply'.

8.3.2 STP Global (Spanning Tree Protocol)

RSTP (Rapid Spanning Tree Protocol) eliminates physical loops in the LAN, ensuring a stable network topology.

  1. Navigate to 'Configuration > Loop > STP global'.
  2. Configure 'Spanning Tree Status', 'Force Version', 'Priority', 'Maximum Age', 'Hello Time', and 'Forward Delay'.
  3. Click 'Apply'.

8.3.3 STP Port

To configure STP settings for individual ports:

  1. Navigate to 'Configuration > Loop > STP port'.
  2. Configure 'Path Cost', 'Priority', 'P2P', and 'Edge' settings for each port.
  3. Click 'Apply'.

8.4 IGMP Snooping

IGMP Snooping manages and controls multicast groups, optimizing multicast traffic flow.

  1. Navigate to 'Configuration > IGMP'.
  2. Enable or disable 'IGMP Snooping'.
  3. You can also 'Dump IGMP entry' to view multicast group entries.
  4. Click 'Apply'.

Link Aggregation (LAG) bundles multiple physical interfaces into a single logical interface (Eth-Trunk) to increase bandwidth and reliability.

In static mode, Eth-Trunks are manually configured without LACP. All active links participate in data forwarding and share traffic. If an active link fails, traffic is automatically shared among remaining links.

  1. Navigate to 'Configuration > Trunk Group Setting'.
  2. Select a 'Group ID' and 'Type' as 'static'.
  3. Add member ports to the group.
  4. Click 'Add/Modify'.

LACP dynamically aggregates and disaggregates links based on IEEE 802.3ad. It exchanges information with opposite network devices via LACPDU.

  1. Navigate to 'Configuration > Trunk Group Setting'.
  2. Select a 'Group ID' and 'Type' as 'LACP'.
  3. Add member ports to the group.
  4. Click 'Add/Modify'.

Notice: Ensure no member interface is accessing the Eth-Trunk before changing its work pattern.

8.6 Port-based Mirroring

Port Mirroring copies messages from a specified source port to a destination port for network monitoring and troubleshooting.

  1. Navigate to 'Configuration > Port-based Mirroring'.
  2. Select the 'Mirror Direction' (Rx, Tx, or Both) and the 'Mirroring Port' (source port).
  3. Specify the 'Mirrored Port List' (destination port).
  4. Click 'Apply'.

8.7 Port Isolation

Port Isolation prevents messages from flooding between specific ports, enhancing security and controlling traffic flow.

  1. Navigate to 'Configuration > Port Isolation'.
  2. Establish the member list of the interworking group for each port.
  3. Click 'Apply'.

8.8 Bandwidth Control

Bandwidth Control allows you to restrict data transmission and reception rates on physical interfaces.

  1. Navigate to 'Configuration > Bandwidth Control'.
  2. Select the port and 'Type' (Ingress for inbound, Egress for outbound).
  3. Set the 'State' (Enable/Disable) and 'Rate' (Kbit/sec).
  4. Click 'Apply'.

8.9 Jumbo Frame

Jumbo Frames allow for larger Ethernet frames, which can improve network efficiency for certain applications.

  1. Navigate to 'Configuration > Jumbo Frame'.
  2. Set the MTU (Maximum Transmission Unit) of the port.
  3. Click 'Apply'.

8.10 MAC Constraint

MAC Constraint limits the number of MAC addresses learned on a port, enhancing security.

  1. Navigate to 'Configuration > MAC Constraint'.
  2. Set the 'State' (Enable/Disable) and 'Entry Limits' for each port.
  3. Click 'Apply'.

8.11 EEE (Energy Efficient Ethernet)

EEE allows for reduced power consumption during periods of low network activity.

  1. Navigate to 'Configuration > EEE'.
  2. Enable or disable the EEE function.
  3. Click 'Apply'.

9. Security

9.1 MAC Address

The MAC address forwarding table is crucial for fast L2 message forwarding.

The MAC address table automatically generates entries with a limited lifetime (aging time). Proper aging time is important for switch performance.

  1. Navigate to 'Security > MAC Address > MAC Search'.
  2. You can view the MAC address table and clear dynamic entries.

9.1.2 Static MAC

Static MAC entries are manually configured and do not age, providing persistent MAC address assignments.

  1. Navigate to 'Security > MAC Address > Static MAC'.
  2. Enter the MAC Address, VLAN ID, and Port for the static entry.
  3. Click 'Add'.

9.2 Storm Control

Storm Control prevents network instability caused by broadcast, unknown multicast, and unicast storms by suppressing messages based on packet rates.

  1. Navigate to 'Security > Storm Control'.
  2. Select the 'Storm Type' (Broadcast, Known Multicast, Unknown Unicast, Unknown Multicast).
  3. Set the 'State' (Off/On) and 'Rate' (kbps) for each port.
  4. Click 'Apply'.

10. Monitoring

10.1 Port Statistics

This section displays real-time statistics for each port, including link status, transmitted/received good packets, and bad packets.

  1. Navigate to 'Monitoring > Port Statistics'.
  2. View the statistics for each port.
  3. You can click 'Clear' to reset the statistics.

11. Tools

11.1 Firmware Upgrade

To upgrade the switch's firmware:

  1. Navigate to 'Tools > Firmware Upgrade'.
  2. Select the firmware file from your local machine.
  3. Click 'Upgrade'.

Notice: Do not power off the device during the upgrade process. Stay on the upgrade page for approximately 1 minute until the upgrade is complete.

11.2 Configuration Backup

To back up or restore the switch's configuration:

  1. Navigate to 'Tools > Configuration Backup'.
  2. Click 'Backup' to save the current configuration to your local machine.
  3. To restore, select a configuration file and click 'Restore'.

11.3 Reset

To restore the switch to factory default settings:

  1. Navigate to 'Tools > Reset'.
  2. Click 'Restore' to perform a factory reset and reboot the system.

11.4 Reboot

To restart the switch:

  1. Navigate to 'Tools > Reboot'.
  2. Click 'Reboot' to restart the system.

11.5 Logout

To exit the web management system:

  1. Navigate to 'Tools > Logout'.
  2. Click 'Login' on the logout page.

12. User Tips

  • GPON Stick Compatibility: This switch has been reported to work effectively with GPON ONU sticks for Fiber-to-the-Home (FTTH) setups.
  • Firmware Updates for Stability: If experiencing issues such as the switch forgetting its set IP address (DHCP issues), check for and apply the latest firmware updates. Firmware updates can often resolve stability and configuration retention problems.
  • LACP 802.3ad Support: The switch fully supports LACP (Link Aggregation Control Protocol) based on the 802.3ad standard, allowing for increased bandwidth and link redundancy.
  • SNMP for Monitoring: The switch supports SNMP (Simple Network Management Protocol), enabling detailed monitoring of per-port traffic statistics and other network parameters.
  • VLAN Flexibility: The VLAN configuration is highly flexible, allowing you to assign specific ports, including the 10G SFP+ port and RJ45 ports, to different VLANs as needed for network segmentation.

13. Troubleshooting

13.1 Cannot Access Web Management Interface

  • Check IP Address: Ensure your PC's IP address is in the same subnet as the switch (e.g., PC: 192.168.2.10, Switch: 192.168.2.1, Subnet Mask: 255.255.255.0).
  • Verify Cable Connection: Ensure the Ethernet cable is securely connected between your PC and the switch.
  • Browser Compatibility: Use a compatible web browser (Chrome, Firefox, or IE 9.0+).
  • Default Credentials: Confirm you are using the default username 'admin' and password 'admin' for initial login.

13.2 DHCP Issues / IP Address Not Retained

  • Firmware Update: This issue can often be resolved by updating the switch firmware to the latest version. Refer to Section 11.1 for firmware upgrade instructions.
  • Static IP Configuration: If using a static IP, double-check the settings in 'System > IP Setting'.

13.3 Network Performance Issues

  • Check Port Status: Use 'Monitoring > Port Statistics' to check for errors or high traffic on specific ports.
  • Verify Cable Quality: Ensure all Ethernet cables are Cat5e or above for 2.5GbE connections and appropriate fiber cables for SFP+ ports.
  • Loop Detection: Enable 'Loop Detection' under 'Configuration > Loop > Loop Protocol' to identify and prevent network loops.
  • Bandwidth Control: Review 'Configuration > Bandwidth Control' settings to ensure no unintended rate limits are applied.

13.4 VLAN Configuration Problems

  • Review 802.1Q VLAN Settings: Double-check port assignments (Tagged/Untagged) and VLAN IDs in 'Configuration > VLAN > 802.1Q VLAN'.
  • Check PVID: Ensure the PVID for each port is correctly configured in 'Configuration > VLAN > 802.1Q VID'.

14. Warranty and Support

HORACO provides a 1-year free warranty and lifetime professional technical support for this product. For any technical assistance or warranty claims, please contact HORACO customer service.

For additional item guides and documents, including the user manual in PDF format, please refer to the official product page or contact support. The PDF manual can be referenced at User manual (PDF).

© 2024 HORACO. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.