PHYEE 16P2TIGGO5

Contents

PHYEE Radio Wiring Harness Adapter and CAN Bus Decoder User Manual

Model: 16P2TIGGO5

1. Introduction

The PHYEE Radio Wiring Harness Adapter with integrated CAN Bus Decoder is designed to facilitate the installation of an aftermarket Android head unit in Chery Grand Tiggo 5 (2014+) vehicles. It ensures proper communication between the new head unit and the vehicle's CAN Bus system, enabling features like steering wheel controls and reverse camera input.

NOTE: The radio must be a 16-Pin connector Android system!

2. Safety Information

  • Always disconnect the vehicle's battery before performing any electrical work to prevent short circuits and damage.
  • Professional installation is highly recommended for car electronics to ensure correct wiring and functionality.
  • Ensure all connections are secure and properly insulated to prevent electrical hazards.
  • Do not modify the wiring harness or CAN Bus decoder unless explicitly instructed. Unauthorized modifications can void the warranty and cause damage.

3. Product Overview

The PHYEE wiring harness adapter and CAN Bus decoder kit includes the following components:

  • 16-Pin to Chery Tiggo 5 Wiring Harness (with 16-pin plug connector and 16-pin + 16-pin female connectors)
  • CAN Bus Decoder Box (Raise)
  • FAKRA Male Car Antenna Cable (Optional, included with some variants)

PHYEE Radio Wiring Harness Adapter and CAN Bus Decoder
Figure 1: Complete PHYEE Radio Wiring Harness Adapter and CAN Bus Decoder Kit.

Close-up of 16-Pin Male Plug and 32-Pin Connector
Figure 2: Detailed view of the 16-Pin Male Plug and 32-Pin Connector.


Video 1: Product demonstration and overview of the wiring harness and CAN Bus decoder.

4. Specifications

FeatureDescription
Model Name16P2TIGGO5
Item TypeCables, Adapters & Sockets
Brand NamePHYEE
Voltage12 V
MaterialCopper
Item Weight0.09kg
Item SizeChery Tiggo 5 harness adapter
PCB IncludedYes
IS It With PCBYes
High-concerned chemicalNone
Special FeaturesVideo input
16 Pin Plug16 Pin Plug
16P/16P Female Connector16P/16P Female Connector
Can Bus DecoderCan Bus Decoder

5. Compatibility

This wiring harness adapter and CAN Bus decoder is compatible with:

  • Vehicle: Chery Tiggo 5 (Grand Tiggo) models from 2014 onwards, equipped with a Quadlock connector.
  • Head Unit: Aftermarket Android head units featuring a 16-pin socket.

6. Setup and Installation

Follow these steps for proper installation:

6.1. Wiring Diagram and Pinout

Refer to the detailed wiring diagram below for correct connections. Each wire is color-coded and labeled for easy identification.

Wiring Diagram for 16-Pin Harness
Figure 3: Wiring diagram showing pin assignments for the 16-pin harness.

  • Speaker Wires: White (FL+), White/black striped (FL-), Gray (FR+), Gray/black striped (FR-), Green (RL+), Green/black striped (RL-), Purple (RR+), Purple/black striped (RR-).
  • Power Wires: Black (GND - Ground Wire / B-), Yellow (BATTERY - Constant Power Supply +12V), Red (ACC - Ignition Switch).
  • Control Wires: Orange (ILLUMINATION - Illuminate Backlight), Pink (REVERSE - Reversing camera control line), Brown/white (KEY2 - Steering Wheel Control 2), Brown (KEY1 - Steering Wheel Control 1), Blue (ANT - Auto Antenna Power).
  • Video Input: Yellow RCA connector labeled "CAM VIDEO IN" for camera video input.

6.2. Connection Steps

  1. Connect Harness to CAN Bus Decoder: Plug the 8-pin connector from the wiring harness into the corresponding socket on the CAN Bus decoder box.
  2. Connect Harness to Head Unit: Connect the 16-pin plug from the wiring harness to the 16-pin socket on your aftermarket Android head unit.
  3. Connect Reverse Camera Input: Plug the yellow RCA connector labeled "CAM VIDEO IN" from the harness into the reverse camera video input port on your Android head unit.
  4. Connect Vehicle Wiring: Connect the vehicle-specific connectors from the wiring harness to your car's existing wiring. Ensure a secure fit for all connections.

CAN Bus Decoder connected to harness
Figure 4: CAN Bus decoder connected to the wiring harness.

Harness connected to Android head unit
Figure 5: Wiring harness connected to the rear of an Android head unit.

7. Operating Instructions (CAN Bus Setting)

After physical installation, you need to configure the CAN Bus settings on your Android head unit:

  1. Enter Factory Settings: Access your Android system's factory settings. This usually requires a password (refer to your head unit's manual for the specific password).
  2. Navigate to CAN Bus Part: Locate the "CAN Bus Part" or similar setting within the factory settings menu.
  3. Choose CAN Bus Decoder Type: Select the correct CAN Bus decoder brand. For this product, it is typically "Raise/睿志诚".
  4. Select Car Brand and Model/Year: Choose your car's brand (Chery) and then the specific model and year (Tiggo 5, 2014+).

CAN Bus Setting Operation Screen
Figure 6: Screenshot illustrating the CAN Bus setting operation on an Android head unit.

CAN Bus Setting Steps Table

No.Decoder LabelSetting Step 1 (CAN Bus Setting)Setting Step 2 (Car Brand)Setting Step 3 (Car Model & Year)
1Raise/睿志诚Raise/RZCCheryTiggo 5 (2014+)
2HiworldHiworldWC/Car BrandCar Model & Year
3ODOD/OudiCar BrandCar Model & Year
4SimpleSoftSimpleSoft/XP/XINPUCar BrandCar Model & Year
5LuZhengLuZheng/LZCar BrandCar Model & Year

Connect your Android system to the internet to update the CAN Bus APK version if necessary.

8. Maintenance

  • Keep all connections clean and free from dust or moisture.
  • Periodically check for any loose connections, especially after driving on rough terrain.
  • Avoid exposing the wiring harness and decoder to extreme temperatures or direct sunlight for prolonged periods.

9. Troubleshooting

  • No Power to Head Unit: Double-check all power connections (Battery+, ACC, GND). Ensure the 16-pin plug is fully seated into the head unit. Verify the vehicle's fuse box for any blown fuses.
  • Steering Wheel Controls Not Working: Confirm the CAN Bus decoder is correctly connected to the harness and the head unit. Re-enter the Android system's factory settings and ensure the correct CAN Bus decoder type, car brand, and model/year are selected.
  • Reverse Camera Not Displaying: Check the yellow RCA "CAM VIDEO IN" connection to the head unit. Ensure the pink "REVERSE" wire is correctly connected to the reverse signal line in the vehicle.
  • No Sound from Speakers: Verify all speaker wire connections (FL+, FL-, FR+, FR-, RL+, RL-, RR+, RR-). Ensure the head unit's audio settings are correctly configured.
  • CAN Bus Decoder Not Recognized: Ensure the 8-pin connector is firmly plugged into the CAN Bus decoder. If an internet connection is available, try updating the CAN Bus APK version on your Android head unit.

10. User Tips

  • Before starting the installation, carefully verify that all included wires in the kit match your vehicle's existing wiring and the head unit's requirements. This can prevent compatibility issues.
  • Always double-check the compatibility of the harness with your specific car model and year. If your vehicle is a variant (e.g., "DR 6" Chery Tiggo 5), it might have different wiring. If unsure, contact the seller for clarification before installation.

11. Warranty and Support

This product comes with a 1-year warranty from the date of purchase.

For any problems, questions, or technical support, please contact the PHYEE Store on Aliexpress directly. They can provide assistance with installation, troubleshooting, and warranty claims.

For additional item guides and documents, please refer to the User manual (PDF) available at this link.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.