SUSWE U-Shaped 240W/252W Power Module

Contents

SUSWE U-Shaped 240W/252W Power Module Instruction Manual

1. Introduction

The SUSWE U-Shaped 240W/252W Power Module is a compact, high-power density green module power supply designed for various applications. It features AC/DC dual-use capability, a wide input voltage range, high reliability, low power consumption, and safe isolation. This module is suitable for industrial control, power instrumentation, smart home devices, and new energy fields where space is a critical factor. It is designed to adapt to corresponding EMC peripheral circuits to meet diverse industry requirements.

2. Specifications

For detailed specifications, please refer to the official user manual PDF: SUSWE Power Module User Manual (PDF).

2.1. Electrical Characteristics

ParameterDescription
Input Voltage RangeAC 85-265V or DC 100V-375V
Normal Voltage RangeAC 110V-240V
Input Frequency Range47Hz-63Hz
Max. Input Current (full load 115Vac)4.5A Max.
Inrush Current (cold start 264Vac)100A Max.
Power Correction Factor (full load 230Vac)0.95 MIN
Efficiency (full load 230Vac)94% MIN
Standby Power Loss<1W
Output Voltage (SKU 24V)+24V
Rated Current (SKU 24V)10.0A
Output Power (SKU 24V)240W
Output Voltage (SKU 36V)+36V
Rated Current (SKU 36V)7.0A
Output Power (SKU 36V)252W
Voltage Accuracy±5%
Load Adjustment Rate±3%
Ripple & Noise (+24V)240mVp-p Max. (Tested with 10uF/EC and 0.1uF/Ceramic capacitors, 20MHz bandwidth)
Undershoot and Overshoot (+24V)±10%
Voltage Rise Time (+24V)≤30mS (10% to 90% output voltage rise)
Temperature Coefficient (+24V)≤0.05%/℃

2.2. Protection Features

  • Short Circuit Protection: Hiccup and auto-recovery.
  • Over Current Protection: ≥11A for +24V output, with hiccup and auto-recovery.
  • Over Voltage Protection: 27 Type, with hiccup and auto-recovery. (Note: Overvoltage protection should be tested under light load or no load conditions.)

2.3. Isolation

  • Hi-pot Test (Input to Output): 1800Vac, 10mA, for 2 seconds.
  • Insulation Resistance (Input to Output): ≥100MΩ at 500Vdc for 1 second.

2.4. Environmental Requirements

  • Operating Temperature: 0°C to 50°C
  • Storage Temperature: -10°C to 70°C
  • Operating Humidity: 10-85% RH, non-condensing
  • Storage Humidity: 5-95% RH, non-condensing
  • Altitude: 5000m
  • Cooling Method: Natural air cooling (ventilation cooling)

2.5. Reliability

  • MTBF (Mean Time Between Failures): 50,000 hours at 25°C.
  • Burn-in: 100% burn-in with 80-100% rated load at 35-45°C ambient temperature for 4 hours.

2.6. Physical Dimensions

The power module has compact dimensions, making it suitable for various integrations.

  • Overall Dimensions: 120 mm (Length) x 71 mm (Width) x 37.5 mm (Height)
  • Unit: Millimeters (mm)
  • Tolerance: ±0.5mm (for unmarked dimensions)
Power module with dimensions 120mm x 71mm x 37.5mm
Figure 1: Power module with key dimensions indicated.
Power module shown next to a smartphone for size comparison
Figure 2: Power module size comparison with a smartphone.

3. Setup and Installation

3.1. Wiring Instructions

The power module features clearly marked input and output terminals for easy connection. Always ensure power is disconnected before making any wiring changes.

  • AC Input (110-240V): Connect the AC input wires to the terminals labeled 'ACL' and 'ACN'. Ensure correct polarity if applicable, typically indicated by '+' and '-' or 'L' and 'N'.
  • DC Output (24V/36V): Connect the DC output wires to the terminals labeled 'V+' and 'V-'. Ensure correct polarity, connecting the positive wire to 'V+' and the negative wire to 'V-'.
Top view of the power module showing input and output terminals
Figure 3: Top view of the power module with input (AC) and output (DC) terminals.
Side view of the power module
Figure 4: Side view of the power module.
Another top view of the power module
Figure 5: Another top view of the power module.

3.2. Mounting

The module is designed for integration into larger systems. Refer to the dimension diagram in Section 2.6 for mounting hole locations and sizes. Ensure adequate ventilation around the module for optimal performance and heat dissipation.

3.3. Safety Precautions

  • Always ensure the power supply is disconnected before installation or maintenance.
  • Incorrect wiring or usage methods can lead to electric shock, damage, smoke, or light emission.
  • Do not place anything on the product before power on, as this may lead to damage, deformation, or burns.
  • Use this product strictly within the specified input voltage and operating temperature ranges.
  • Avoid placing the product in high temperature, high humidity, dusty, or corrosive environments, as this may cause damage or electric shock.

4. Operating Instructions

Once properly installed and wired, the power module operates automatically within its specified parameters. Ensure the load connected does not exceed the rated output current and power for the selected voltage variant (24V/10A/240W or 36V/7A/252W).

4.1. Performance Curves

The performance of the power module, including voltage derating curves based on input voltage and ambient temperature, are detailed in the full specification document (Section 6, Product Performance Curve). These curves illustrate how the maximum output power may be affected by varying input conditions and environmental factors.

4.2. Product Demonstration Video

Video 1: Product demonstration showing AC input wiring, DC output wiring, testing with an LED strip, and a robustness test involving water immersion.

5. Maintenance

5.1. General Care

  • Keep the power module clean and free from dust.
  • Ensure proper ventilation to prevent overheating.
  • Avoid exposure to moisture or corrosive substances.

5.2. Storage Guidelines

If the product is stored for longer than 6 months under specified storage conditions, it is recommended to power on the product and let it operate for more than 2 hours. This helps maintain product life and prevent potential issues from prolonged inactivity.

6. Troubleshooting

The power module is equipped with several protection mechanisms to ensure safe operation. If the module stops functioning, check the following:

  • No Output Power: Verify that the input voltage is within the specified range (AC 85-265V or DC 100V-375V) and that all wiring connections are secure and correct.
  • Short Circuit Protection: If a short circuit occurs at the output, the module will enter hiccup mode and automatically recover once the short circuit is removed. Remove the short and power cycle the module if necessary.
  • Over Current Protection: If the output current exceeds the rated limit (e.g., >11A for 24V output), the module will activate overcurrent protection, entering hiccup mode and auto-recovering when the overload is removed. Reduce the load to within specifications.
  • Over Voltage Protection: In case of an overvoltage condition (Type 27), the module will also enter hiccup mode and auto-recover. Ensure the load is appropriate and not causing voltage spikes.
  • Overheating: If the module is operating in an environment exceeding its maximum operating temperature (50°C) or lacks sufficient ventilation, it may shut down. Ensure proper airflow and ambient temperature.

If the issue persists after checking these points, consult the full specification document or contact customer support.

7. Warranty and Support

For information regarding product warranty, technical support, or service, please contact the seller or manufacturer directly. Keep your purchase records handy when seeking support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.