Tedeligo TEDE 12V 24V Dimmer Light Switch

Contents

Tedeligo LED Dimmer Switch and Wireless Wall Switch User Manual

Model: TEDE 12V 24V Dimmer Light Switch

1. Product Overview

This manual provides instructions for the Tedeligo 433MHz LED Dimmer Switch and its accompanying Wireless Wall Switch. This system allows for wireless control of brightness, lighting modes, and speed for various DC 5-24V LED lighting fixtures and motors.

Tedeligo LED Dimmer Switch and Wireless Wall Switch
Figure 1: Tedeligo LED Dimmer Switch and Wireless Wall Switch

The dimmer controller operates on DC 5-24V and has a maximum current of 30A. The wall-mounted touch panel switch features a stable capacitive touchscreen for smooth operation and includes various control buttons for comprehensive light management.

2. Specifications

2.1 Dimmer Switch Parameters

ParameterValue
RF Frequency433.92 MHz
Working VoltageDC 5-24V (5V, 6V, 12V, 24V)
Max Current30 A
Connect Port+V, -V
Switch Size86*63*22 mm
Max. Load Power500 W
Output PowerEquals input power
Operation Temperature20-80 Celsius

2.2 RF Wall Panel Switch Parameters

ParameterValue
RF Frequency433.92 MHz
Size86*86*10 mm
MaterialGlass panel and Plastic
Battery1*CR2025 (Included)

3. Setup Instructions

3.1 Wiring the LED Dimmer Switch

Ensure power is disconnected before wiring. The dimmer switch is designed for DC 5-24V input and output. Connect your power supply to the 'INPUT' terminals and your LED lighting fixture (e.g., LED strip, COB light strip, Bulbs, Motors) to the 'OUTPUT' terminals. Ensure correct polarity (+V to +V, -V to -V).

Wiring diagram for Tedeligo LED Dimmer Switch with LED strip
Figure 2: Wiring Diagram for LED Dimmer Switch
Dimmer connected to various LED lighting types
Figure 3: Dimmer compatibility with LED strips, COB lights, and bulbs

3.2 Installing the Wall Panel Switch

The wall panel switch can be installed using two methods:

  1. Using Double-Sided Tape:
    a. Prepare double-sided tape.
    b. Stick the double-sided tape on the back of the wall panel switch.
    c. Paste the switch onto a smooth wall surface.
  2. Using Screws (Product does not come with screws):
    a. Open the back cover of the wall panel switch.
    b. Fix the switch to the wall using appropriate screws.
    c. Fully snap the control panel into place.
Wall panel installation methods using tape and screws
Figure 4: Wall Panel Installation Methods

3.3 Pairing the Wall Switch with the Dimmer

  1. Ensure the dimmer switch is powered on.
  2. On the wall panel switch, press and hold the 'Night Light' button (moon icon) for 5 seconds. The connected light bar will flash slowly 3 times to indicate successful pairing.
Instructions for pairing the wall switch with the dimmer
Figure 5: Pairing Instructions

4. Operating Instructions

The wall panel switch provides comprehensive control over your connected LED lights. Refer to Figure 6 for button layout.

Detailed view of the wall switch buttons and their functions
Figure 6: Wall Switch Button Functions

4.1 Button Functions

  • 1. Night Light Button (Moon icon): Activates a low brightness setting suitable for night.
  • 2. Max Brightness Button (Sun with 100% icon): Sets the light to maximum brightness.
  • 3. Mode Setting Button (Gear icon): Cycles through various lighting modes (e.g., gradient, jump, fade, flicker, flash).
  • 4. ON/OFF Button (Power icon): Toggles the light on or off.
  • 5. Speed - Button (Rocket icon pointing left): Decreases the speed of dynamic lighting modes.
  • 6. Speed + Button (Rocket icon pointing right): Increases the speed of dynamic lighting modes.
  • 7. 2H Delay Button: Sets a 2-hour delay before the light turns off.
  • 8. 1H Delay Button: Sets a 1-hour delay before the light turns off.
  • 10. Brightness +/- Zone (Circular touch area): Touch and slide your finger along the circular area to adjust the brightness level.

4.2 Demonstration Video

For a visual guide on operating the dimmer switch and wall panel, please watch the demonstration video below:

Video 1: Tedeligo LED Dimmer Switch and Wall Switch Functionality Demonstration. This video shows how to turn the light on/off, adjust brightness, change modes, and control speed using the wall switch.

5. Maintenance

5.1 Cleaning RF Data (Unpairing)

To clear all paired RF data from the dimmer switch:

  1. Ensure the dimmer switch is powered on.
  2. Press and hold the 'Max Brightness' button (Sun with 100% icon) on the wall panel switch for 5 seconds. The connected light bar will flash quickly 3 times to indicate that the RF data has been successfully cleared.

5.2 Battery Replacement

The wall panel switch features a convenient battery bay design, allowing for easy battery replacement without opening the entire casing. The wall panel uses one CR2025 battery.

Wall panel with battery bay open showing CR2025 battery
Figure 7: Battery Bay Design for Easy Replacement

5.3 Cleaning the Glass Panel

The wall panel is made of tempered glass, which is easy to clean and resistant to scratches. Use a soft, damp cloth to wipe the surface. The panel is designed to be responsive even with wet hands.

Tempered glass panel showing durability and wet hand touch feature
Figure 8: Tempered Glass Panel Features

6. Troubleshooting

  • Light not working after connection: Ensure your lighting fixture is DC 5-24V. This dimmer is not compatible with AC power. Verify all wiring connections for correct polarity and secure terminals.
  • Night light returns to Max brightness: If the night light setting reverts to maximum brightness, try re-pairing the wall switch with the dimmer as described in Section 3.3. If the issue persists, clear the RF data (Section 5.1) and then re-pair.
  • Wall switch unresponsive: Check the CR2025 battery in the wall panel switch and replace it if necessary. Ensure the switch is within the effective RF range (approximately 20-50m in open space) of the dimmer.

7. User Tips

  • Always double-check the voltage requirements of your LED lights to ensure compatibility with the DC 5-24V dimmer.
  • When installing the wall panel, consider using the double-sided tape for temporary placement or if you prefer not to drill holes. For a more permanent fixture, use screws.
  • Familiarize yourself with the different lighting modes and speed controls to customize your lighting experience.

8. Warranty and Support

This product comes with a 1-year warranty. For any issues or support, please contact the seller. You can also refer to the official user manual PDF for additional details: View User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.