Introduction
The HTI HT-19 is a professional-grade infrared thermal camera designed for accurate and efficient temperature testing across various industrial and commercial applications. Featuring a high-resolution 320x240 infrared sensor and a clear 3.2-inch full-color display, this device provides detailed thermal images to help identify heat sources and potential issues. Its robust design, rechargeable battery, and user-friendly interface make it an essential tool for professionals in fields such as electrical inspection, building diagnostics, HVAC, and automotive repair.

Package Contents
Before using your HTI HT-19 Thermal Camera, please ensure all items listed below are present in the package:
- 1 x HTI HT-19 Infrared Thermal Imager
- 1 x USB Cable
- 1 x User Manual
- 1 x Carry Pouch
- 1 x Carry Pouch Strap
- 1 x Cardboard Package Box
- 1 x Power Plug (Charger)

Setup
1. Initial Charging
The HTI HT-19 is equipped with a built-in rechargeable 18650 battery. Before first use, fully charge the device. Connect the provided USB cable to the camera's Micro USB 2.0 port and the other end to the power plug, then plug it into a wall outlet. A full charge typically allows for approximately 3 hours of continuous working time.

2. SD Card Installation
The camera comes with a 4GB SD card for image storage. Ensure it is properly inserted before use. The SD card slot is typically located on the side or bottom of the device. Refer to the functional diagram for precise location.
Operating Instructions
1. Device Overview and Controls
Familiarize yourself with the camera's components and control buttons:

- On/Off Key: Press and hold to power the device on or off.
- Menu Key: Access the main menu for settings and options.
- Select Key: Confirm selections within the menu.
- Enter Key: Execute selected functions or enter sub-menus.
- Navigation Keys (Up, Down, Left, Right): Navigate through menu options and adjust settings.
- Image Capture Key: Press to save the current thermal image.
2. Powering On and Basic Operation
- Press and hold the On/Off key to power on the thermal camera.
- The 3.2-inch full-color screen will display the thermal image.
- Point the camera at the object you wish to measure. The screen will show the temperature distribution.
- Press the Image Capture Key to save the current thermal image to the SD card.
3. Adjusting Settings (Color Palettes, Vision Options)
The HT-19 offers various settings to optimize your thermal imaging experience:

- Color Palettes: Press the Menu key, navigate to "Palette" and select from options like Rainbow, Iron Red, Cold Color, Black & White, and White & Black to visualize temperature differences.
- Vision Option: The HT-19 supports 2 kinds of visual mode switching and 5 kinds of full infrared to full visual mixing, allowing you to accurately detect fault points based on measurement comparison. Access these options via the menu.
- Emissivity: Adjust emissivity (0.1-10.0) based on the material being measured for accurate temperature readings. This setting can be found in the menu.
- Auto Power-off: Configure the automatic shut-down time (5 minutes, 20 minutes, or never) to conserve battery life.
- Unit Adjustment: Change temperature units between Celsius and Fahrenheit.
- Language: Select your preferred language for the interface.
- Date/Time Format: Set the date and time display format.
4. Image Transfer
Captured images can be transferred to a computer or other devices using the common USB cable.

Maintenance
- Cleaning: Use a soft, dry cloth to clean the camera body. For the lens and screen, use a specialized lens cleaning cloth and solution to avoid scratches. Do not use abrasive cleaners or solvents.
- Battery Care: To prolong battery life, avoid fully discharging the battery frequently. Charge the device regularly, even if not in use for extended periods. Store the camera with a partial charge (around 50%) if storing for a long time.
- Storage: Store the camera in its protective carry pouch in a cool, dry place, away from direct sunlight, extreme temperatures, and high humidity.
- Protective Cover: Always keep the protective cover over the visible light camera and infrared imaging sensor when not in use to prevent dust and damage.
Troubleshooting
- Device not powering on:
- Ensure the battery is sufficiently charged. Connect the camera to a power source and try again.
- Press and hold the On/Off button for several seconds.
- Blurred or unclear thermal images:
- Check if the lens is clean. Gently clean it with a lens cleaning cloth.
- Ensure the object is within the optimal focal length (0.5m for HT-19).
- Verify that the emissivity setting is appropriate for the material being measured.
- Cannot save images:
- Check if the SD card is properly inserted.
- Ensure there is sufficient space on the SD card.
- Try formatting the SD card (this will erase all data, so back up first).
- Inaccurate temperature readings:
- Confirm the correct emissivity setting for the target surface.
- Ensure the camera is within its specified operating temperature range (0 to 50°C).
- Avoid measuring through reflective surfaces like glass or polished metals without adjusting emissivity.
Specifications
Detailed technical specifications for the HTI HT-19 Thermal Camera:
| Feature | Specification (HT-19) |
|---|---|
| Display | 3.2'' full-color screen |
| Infrared Image Resolution | 320 x 240 pixels |
| Total Pixel | 76,800 pixels |
| Visible Image Resolution | 0.3 million pixels |
| Thermal Sensitivity | 0.07°C |
| Temperature Range | -20℃ to 300℃ (-4℉ to 572℉) |
| Measuring Accuracy | ±2.5℃ or ±2.5% |
| Emissivity | 0.1-10.0 Adjustable |
| Focus Mode | Fixed |
| Image Frequency | 9Hz |
| Vision Option | 5 kinds of full infrared to full visual, mixing visible and infrared. |
| Image Storage | SD card (4G) |
| Image Format | JPG |
| USB Interface | Micro USB 2.0 |
| Power Supply | Built-in rechargeable 18650 batteries |
| Auto Power-off Time | 5 minutes / 20 minutes / not power off automatically |
| FOV/Shortest Focal Length | 27°×35° / 0.5m |
| Wavelength Range | 8-14μm |
| Size | 223 x 105 x 90mm |
| Weight | 289g |
| Palette | Iron red, rainbow, rainbow high contrast, gray scale (white glow), gray scale (black glow) |
| Set Control | Unit Adjustment / Language / Date Time Format / Automatic Shut Down |
| Authentication | CE, RoHS |
| Work Temperature | 0 to 50°C |
| Storage Temperature | -40 to 80°C |
| Relative Humidity | 10%RH to 80%RH |

User Tips
- For best results, ensure the camera lens is clean before each use. Dust or smudges can affect image clarity.
- When comparing thermal images, utilize the mixed visible and infrared modes to better contextualize temperature anomalies with the actual object.
- Remember to adjust the emissivity setting for different materials to get the most accurate temperature readings. Common emissivity values can be found online or in specialized guides.
- Take advantage of the automatic shut-down feature to conserve battery life, especially during prolonged use or when the device is idle.
Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the contact details provided by your retailer or the manufacturer's official website. Keep your purchase receipt as proof of purchase for any warranty claims.