1. General Introduction
The XTOOL D7W smart diagnostic system, referred to as the "Scan Tool", is an advanced scanning tool based on the Android operating system. It supports multiple languages and is suitable for different countries and regions. This OBD-II (On-Board Diagnostics version 2) scanner offers comprehensive functions and quickly provides accurate diagnostic information.
The D7W is an upgraded version of the D7 series, specifically designed to support WiFi connection diagnostics, offering a wider diagnostic range and enhanced convenience.

Figure 1: XTOOL D7W Tablet and VCI Box with Live Data Display
Video 1: XTOOL D7W Product Overview. This video demonstrates the key features and functionalities of the XTOOL D7W Wireless Auto Diagnostic Tool, including its wireless capabilities, diagnostic functions, and user interface.
2. Safety Information
For your own safety and the safety of others, and to prevent damage to the device and vehicles upon which it is used, it is important that the safety instructions presented throughout this manual be read and understood by all persons operating or coming into contact with the device.
There are numerous procedures, techniques, tools, and parts required for servicing vehicles, as well as the skills of the person doing the work. Because of the vast number of test applications and variations in the products that can be tested with this equipment, we cannot possibly anticipate or provide advice or safety messages to cover every circumstance. It is the automotive technician's responsibility to be knowledgeable of the system being tested. It is crucial to use proper service methods and test procedures. It is essential to perform tests in an appropriate and acceptable manner that does not endanger your safety, the safety of others in the work area, the device being used, or the vehicle being tested.
Before using the device, always refer to and follow the safety messages and applicable test procedures provided by the manufacturer of the vehicle or equipment being tested. Use the device only as described in this manual. Be sure to read, understand, and follow all safety messages and instructions in this manual.
Safety Instructions
The safety messages herein cover situations Xtool is aware of at the time of publication. Xtool cannot know, evaluate or advise you as to all of the possible hazards. You must be certain that any condition or service procedure encountered does not jeopardize your personal safety.
3. Setup and Initial Configuration
3.1 Package Contents
The XTOOL D7W package includes the following items:
- 1PC X D7W Tablet
- 1PC X USB Cable
- 1PC X Charger for Tablet
- 1PC X Charger US Adapter
- 1PC X Charger EU Adapter
- 1PC X Charger UK Adapter
- 1PC X Color Carton
- 1PC X Certificate of Quality
- 1PC X Tool Case
- 1PC X Quick Start Guide

Figure 2: XTOOL D7W Package Contents
3.2 Device Overview
The XTOOL D7W system consists of a tablet and a VCI (Vehicle Communication Interface) box. Key components are:
Tablet Components:
- ① Type-C Port
- ② Reset Hole
- ③ Power Button
- ④ Microphone
- ⑤ Camera
- ⑥ Tablet Holder
- ⑦ Speaker
- ⑧ Nameplate
VCI Box Components:
- ① OBD Port
- ② Type-C Port
- ③ Nameplate

Figure 3: XTOOL D7W Tablet and VCI Box Overview
3.3 Wireless Connection to Vehicle
- Press and hold the Power button to turn on the tablet.
- Select the App language and start the activation process.
- Input your E-mail address, and click OK to complete the activation.
- Plug the VCI box into the OBD port on the vehicle.
- Ensure the WiFi connection indicator lights on the VCI box are illuminated.
- Your tablet is now ready for diagnostic.

Figure 4: Wireless Vehicle Connection Steps
Note: WiFi is not required when using the device. WiFi connection means VCI is connected to the device through WiFi signal, not using WiFi network to perform diagnosis function.
3.4 Language Setup
The XTOOL D7W supports 22 languages. To set the language:
- Activate the device with your email address and serial number.
- Switch the language in the device settings (Diagnosis App > Settings > Language).
- Click "Updates" in the device to apply the language change.

Figure 5: Steps to Set the Language
The supported languages include: English, French, German, Russian, Spanish, Polish, Italian, Portuguese, Dutch, Danish, Japanese, Finnish, Arabic, Korean, Vietnamese, Thai, Norwegian, Turkish, Hungarian, Greek, Swedish, Traditional Chinese.
4. Operating Instructions
4.1 Precautions for Diagnosis
- The voltage range on the car should be +9~+36V DC.
- When testing some special functions, operate according to prompts and meet test conditions (e.g., engine water temperature 80°C~105°C, headlights and air conditioners off, accelerator pedal released).
- If the vehicle type or electronic control system is not found, upgrade the diagnostic software or consult XTOOL technical service.
- Only use wiring harnesses provided by XTOOL to avoid damage.
- When running a Diagnostics function, do not shut down the device directly. Cancel the task before returning to the main interface.
4.2 Beginning Diagnostic Testing
After the tablet device is properly connected to the vehicle, you can start the vehicle diagnosis. The diagnostic application can read ECU information, read and clear DTCs (Diagnostic Trouble Codes), check live data, freeze frame data, and perform many types of actuation tests across various vehicle control systems like Engine, Transmission, ABS, SRS, and EPB.
4.3 Vehicle Selection
The scan tool supports three ways to access the smart diagnostics system:
- AUTO SCAN: Supports automatic reading of vehicle VIN code. Tap "AUTO SCAN" on the diagnosis system entrance. Ensure the car and device are well connected.
- MANUAL INPUT: Supports manual input of the 17-character VIN code for accurate test results.
- SELECT VEHICLE BY AREA: Choose a car brand by selecting the appropriate region (Europe, America, Asia, China, etc.) at the top of the screen, then select the vehicle model.
If your model is not recognized:
- Update all software and check if the APP is updated in [Settings].
- Click Diagnosis on the main menu, manually select the engine system, read ECU information, and confirm if the VIN can be read.
- Contact the XTOOL technical team with the VIN code to confirm if the model supports automatic VIN identification.

Figure 6: All System Diagnosis Interface
4.4 Diagnosis Functions
The scan tool supports the following diagnostic functions:
- Read ECU Information: Reads ECU version, software/hardware versions, models, production date, and part numbers.
- Read/Clear Trouble Code: Reads current and historical DTCs. If "System is OK" or "No Trouble Code" is displayed, there are no related trouble codes stored in the ECU or issues are not ECU-controlled. Clear codes after resolving issues.
- Live Data: Displays real-time sensor information (PIDs) like oil pressure, temperature, engine speed, etc. Helps predict problem areas.
- Freeze Frame: Saves data at the moment a sensor signal is abnormal to analyze component failures.
- Actuation Test (Bi-Directional Control): Sends and receives information between the device and vehicle control modules to test actuating components.
- Special Functions: Provides various reset or re-learning functions.
4.4.1 Live Data Display and Graphing
The XTOOL D7W offers an 8-in-1 real-time data display function. You can view up to 8 independent streams of sensor data simultaneously in text or graphic form. This feature allows for:
- Combination of digital graphics and text: Visualizes trends and identifies patterns.
- Data merging function: Supports merging up to 8 different PID graphics into a comprehensive view for comparing relevant parameters.
- Export to CSV format: Export real-time data as a CSV file for tracking performance changes, recording, playback, and viewing.

Figure 7: 8-in-1 Live Data Graphing
4.4.2 Bi-Directional Control / Active Tests
The D7W is a bidirectional scanner that can send commands to systems or components to test their working status without using vehicle controls or disassembling parts. This saves significant time in troubleshooting and repairs.
Examples of active tests include:
- Evaporative emission testing
- Compression testing
- Control of radiator fan switch
- Start/stop of air conditioning clutch
- Fuel pump testing
- Functional testing of windows, rearview mirrors, and door locks
- Testing of pumps and values
- Testing of interior and exterior lights
- Testing of horn sound

Figure 8: Bi-directional Control Functionality
Note: Available active tests vary by vehicle system. Please check compatibility for your specific car model.
4.5 Special Functions (39+)
The D7W supports over 39 common special reset functions, allowing quick access to vehicle systems for scheduled services, maintenance, and reset performance. These functions often eliminate the need to reset codes after resolving common problems.

Figure 9: Overview of 39+ Hot Maintenance Services
4.5.1 ABS Bleeding
This function helps maintain the Anti-Lock Braking System by bleeding air from the system to restore brake sensitivity. It is performed when replacing the brake distributor pump, severe brake fluid shortage, or changing brake fluid.
Operation Guidelines:
- Read operating instructions and precautions on screen.
- Attach bleeder bottle to the left rear bleeder screw.
- Open the left rear bleeder screw.
- Click "OK" to start the bleed procedure, continuously pumping the brake pedal with steady applies every 2 seconds.
- Continue pumping until air bubbles are no longer visible, then select "OK" for the next wheel.
- Repeat for left front, right front, and right rear wheels.
- Stop pumping the brake pedal and close the bleeder screw.
- Click "OK" to complete the procedure.
Caution: The ABS pump screw needs to be unscrewed. Brake fluid will be under pressure during this process. Secure the bleed hose and open bleeder screws slowly. Some vehicles do not support automatic bleeding, but manually bleeding.
4.5.2 Oil Reset
Resets the engine oil life system after an oil change, allowing the system to calculate the next service interval accurately.
Operation Guidelines:
- Enter the Oil Reset menu and choose relevant models.
- Follow on-screen instructions and press OK.
- Enter Maintenance mileage reset menu.
- Click INPUT, enter a reasonable value for remaining oil life, and press OK.
- Confirm the new value and click OK.
- A "Write successfully" message will confirm completion.
4.5.3 EPB (Electronic Parking Brake) Reset
Resets the electronic parking brake system and brake pads after repairs or replacements. This function is used for retracting/releasing brake pumps, G-sensor and body angle calibration.
Operation Guidelines:
- Enter the EPB menu and choose relevant models.
- Follow on-screen instructions and press YES.
- Enter maintenance mode, release the handbrake, and press OK.
- Wait for "Successful operation" message and press OK.
- Enter Exit maintenance mode and wait for "Successful operation" message.
4.5.4 SAS (Steering Angle Sensor) Calibration
Calibrates the steering angle sensor to store the current steering wheel position as the straight-ahead position in the SAS EEPROM. This is necessary after replacing the sensor, steering mechanical parts, four-wheel alignment, or car body repair.
Operation Guidelines:
- Enter the SAS menu and choose relevant models.
- Enter the Set steering angle sensor menu and follow instructions.
- Wait for instructions, then press YES.
- Follow instructions and press OK.
- Wait for instructions, then press OK.
- "Function execution is completed" message confirms success.
4.5.5 BMS Reset
Resets the Battery Management System after battery replacement to clear old fault information and ensure accurate monitoring of the new battery. This prevents false information and invalidation of auxiliary functions.
Operation Guidelines:
- Enter the BMS Reset menu and choose relevant models.
- Turn on the ignition switch.
- Press OK to continue.
- Enter battery capacity (within the given range) and press OK.
- Enter the battery manufacturer and press OK.
- Enter the 10-digit battery serial number and press OK.
4.5.6 Injector Coding
Writes the identification code of the fuel injector into the ECU, allowing the ECU to recognize new injectors. This is crucial after replacing the ECU or injectors to ensure accurate fuel injection control.
Operation Guidelines:
- Enter the Injector coding menu and choose relevant chassis models.
- Enter the Fuel injection nozzle injection volume adjustment menu.
- Read the displayed note carefully and press OK.
- Read and confirm the value stored in the cylinders.
- Enter the Change the value of cylinder menu for the replaced injector(s), enter the new 5-digit value, and press OK.
- Wait for "Write successfully" message.
- Turn off the ignition switch.
- Wait for prompt to turn on the ignition switch.
- Re-enter the Fuel injection nozzle injection volume adjustment menu to verify new values.
Note: In general cases, there is no need to perform the coding matching function after cleaning. The identification of the fuel injector includes its working accuracy value and type value. When replacing an injector you need to find the corresponding model for replacement. At present, mainstream cars support injector coding functions.
4.5.7 DPF Regeneration
Manages Diesel Particle Filter (DPF) regeneration, component replacement teach-in, and DPF teach-in after replacing the ECM. This clears particulate matter from the DPF filter through combustion to stabilize filter performance.
Operation Guidelines:
- Enter the DPF menu and choose relevant models.
- Enter the DPF regeneration menu.
- Read carefully and complete the requisites listed before performing the DPF regeneration function. Press OK.
- Read the fuel tank level and ensure it meets the requirement.
- Read the carbon deposit load.
- Choose "drive to warm up" and follow instructions. Press OK.
- Read instructions carefully and follow them. Press OK.
- Follow displayed instructions and press OK. IMPORTANT: Pay attention to the Note.
- Press OK to start regeneration.
- Wait for carbon deposit value to decrease until "Emergency regeneration has been completed" message appears (up to 40 minutes).
- Wait for 2 minutes for the particulate filter to cool down.
- Press "drop out" to exit the DPF function.
4.5.8 TPMS Reset
Performs learning, matching, and resetting functions for tire pressure sensors. This is done for tire replacement, troubleshooting TPMS problems, or other signal loss issues.
Operation Guidelines (Automatic Relearn):
- Install tire pressure sensor appropriately.
- Adjust all TPMS sensors to the standard value.
- Keep the vehicle at a complete standstill for more than 20 minutes (engine and power off).
- Drive at 30-100km/h for more than 15 minutes.
- The vehicle will automatically relearn the value, and the tire pressure warning will disappear.
- If relearn fails, repeat steps 2-5.
Operation Guidelines (Static Relearn):
- Install all tire pressure sensors appropriately.
- Pull up the parking brake.
- Turn the ignition to ON/RUN with the engine off.
- Enter the tire pressure learning mode through the instrument panel (refer to vehicle manual).
- Starting from the left front wheel, use a TPMS Activation Tool to activate the sensor. The vehicle will sound the horn or flash the turn signal.
- After the left front wheel sensor is relearned, activate remaining sensors in order: right front, right rear, and left rear.
- Turn the vehicle off and power off. Adjust all sensors to standard value.
- Tire pressure warning light will disappear. If procedure fails, repeat steps 4-7.
Operation Guidelines (OBD Relearn):
- A TPMS Activation Tool is needed.
- Install tire pressure sensor appropriately.
- Adjust all TPMS sensors to the standard value.
- Activate all sensors in order: left front, right front, right rear, left rear.
- Connect TPMS Activation Tool to the OBD port and perform OBD relearn function to write sensor ID.
- Turn ignition to ON/RUN, re-trigger all sensors in order: left front, right front, right rear, left rear.
- Keep vehicle powered off for more than 25 minutes.
- Drive at 30-100km/h for more than 15 minutes. If successful, tire pressure warning light will go off. Otherwise, repeat steps 4-7.
Operation Guidelines (Copy ID Relearn):
This method allows copying IDs to new sensors if the new sensor cannot change its own ID. Only OEM equipment can replace sensors that cannot change their ID.
Method 1:
- Use a TPMS Activation Tool to activate the original sensor and copy its ID.
- Program the copied ID into the new sensor using the TPMS Activation Tool (binary ID format must match).
- Remove the original sensor, install the new programmed sensor, and put the tire back on.
Method 2:
- Use the TPMS Activation Tool to connect to the vehicle OBD port, enter the tire pressure system, and copy the ID of the sensor to be replaced.
- Program the copied ID into the new sensor using the TPMS Activation Tool (binary ID format must match).
- Remove the original sensor, install the new programmed sensor, and put the tire back on.
Note: This Scan Tool is not a replacement for the TPMS activation tool. It only provides TPMS Reset/Relearn functions, not activation of TPMS sensors. If you need a professional TPMS activation tool, please consult your local dealer.
4.5.9 Key Programming
The IMMO service can disable lost car keys and program replacement remote keys. This includes programming new remote keys, reading and calculating PIN codes, checking key quantities, generating keys, adding keys, handling all key loss situations, creating dealer keys, reading and writing anti-theft data, backing up IMMO data, remote frequency detection, anti-theft module replacement, and resetting and coding IMMO ECU.

Figure 10: Key Programming Functions
Note: Not all cars support key programming. Please check compatibility for your specific car model.
4.5.10 ECU Coding & PMI & VAG Guided Functions
The D7W is equipped with advanced ECU coding functions to reprogram adaptive data after replacing certain components, improving vehicle performance. It can also utilize hidden features, customize car settings, and disable annoying functions. This tool is applicable for Volkswagen, Skoda, Audi, Mercedes Benz, and Mitsubishi.
- Recode Changed Modules: ECU Coding and Online Coding changed modules to improve car performance and set up your vehicle according to your needs. (Currently only available for VW, Skoda, Audi).
- Renew ECU Coordination: Customization of ECU configuration to make the car's ECU performance more suitable for the car. (Currently only available for BMW, Volkswagen, Audi, Skoda, Toyota, Lexus, SCION, Mazda, Ford, Lincoln).
- Match/Learn/Code Components Module: By matching, relearning, calibrating, and coding, component modules are made more suitable for the operation of automobiles.
- Make Full Use of Hidden Functions: Enable hidden functions and disable infrequently used functions, improve car performance or enable high-end functions.
- Reinforce Performance: Optimize the overall performance of the vehicle by customizing factory settings through retrofitting or modification.
- Programmable Module Installation (PMI): For Ford, Lincoln, and Mazda, the PMI function allows technicians to configure new modules (ECU, TCM, BCM, etc.) to match vehicle specifications and communicate correctly.
- VAG Guided Functions: For VAG vehicles (Audi, Skoda, VW), provides step-by-step guidance through complex procedures like coding, adaptations, programming, and system repairs.

Figure 11: Advanced ECU Coding & Adaptation
4.5.11 CAN FD & DoIP Protocol + FCA Autoauth
- CAN FD Protocol: Built-in support for CAN FD protocol, compatible with GM Vehicles after 2020. Enhances data rates and payloads for more efficient diagnosis.
- DoIP Protocol: Built-in support for DoIP protocol, compatible with BMW E/F/G Chassis, Jaguar, and Land Rover newer vehicles. Enables diagnostic communication over Ethernet for faster data exchange.
- Auto Auth for FCA: Supports Chrysler/Jeep/Dodge/Fiat vehicles after 2018, allowing access to secure gateway modules.

Figure 12: CAN FD, DoIP Protocol, and FCA Autoauth Features
4.6 OBD2 Functions
The XTOOL D7W provides 10 EOBD Functions:
- Read/Clear Trouble Codes
- Live Data
- Read Freeze Frame
- Read ECU Information
- Component Test
- On-Board Monitor Test
- O2 Sensor Monitoring Test
- I/M Readiness
- Read Vehicle Information
5. Maintenance
5.1 Software Updates
After activating the device, you can update the software modules via the "Updates" screen. The device identifies all currently available software packages, which can be downloaded directly via the Internet. The D7W includes 3 years of free software updates.
Cautions:
- When the subscription expires, the installed software is still available, but all updates will be invalid.
- If you delete specific software due to personal operation, XTOOL is not responsible for supporting its restoration.
- To renew your subscription, contact your local dealer or XTOOL technical support.

Figure 13: Software Update and Warranty Information
5.2 Factory Reset
Restoring factory settings in the Android OS system will erase custom settings and data, restart the device, and enter factory reset mode. This is triggered by clicking "Settings" from the main home page, then "Backup & reset". Follow on-screen prompts. After reset, you can select the language in the initial setup interface.
6. Troubleshooting
6.1 DTC Status Descriptions
Understanding Diagnostic Trouble Code (DTC) statuses is crucial for effective troubleshooting:
| DTC Status | Description | Suggestions |
|---|---|---|
| Current/Present | Trouble codes stored in the ECU when both continuous and non-continuous monitors fail. MIL is commanded On. | Can be cleared using Clear DTC function or when ECU monitor completes 40 consecutive trips without fault. |
| History/Stored | Trouble codes stored in the ECU when continuous and non-continuous monitors fail. Not cleared by ECU monitor. | Can only be cleared using the Clear DTC function. |
| Pending | Codes that prep themselves when a fault is determined in an engine cycle. Preliminary investigation for your engine. | Not severe but shouldn't be ignored. Can be cleared using the Clear DTC function. |
| Permanent | Trouble codes stored in the ECU when continuous and non-continuous monitors fail. Set in conjunction with Current and History DTCs. | Cannot be cleared using Clear DTC function. Cleared when ECU monitor completes and passes three consecutive trips. |
| Active/static (For Volkswagen) | Fault is happening at the moment and should be taken care of. | Cannot be cleared directly. Internal fault of the car must be eliminated manually. |
| Passive/sporadic (For Volkswagen) | Fault occurred in the past. | Can be cleared by ScanTool. User should check if DTC reappears. |
6.2 Remote Assistance
The D7W supports remote assistance via TeamViewer QuickSupport. This allows XTOOL technical support or partners to remotely control your tablet to help resolve issues.
Steps to get Remote Support:
- Ensure the tablet is connected to the Internet.
- Tap "Remote" in the Diagnostic application to display the TeamViewer screen and generate your device ID.
- Provide your ID to the XTOOL technician or partner.
- Wait for them to send a remote-control request.
- A pop-up window will ask for permission; click "Allow" to accept or "Reject" to decline.

Figure 14: TeamViewer QuickSupport Interface
7. Specifications
7.1 Hardware Configuration
- Product Name: D7W
- OS: Android 10
- Processor: Quad Core 1.5Ghz
- Memory: 2GB RAM, 64GB ROM
- Screen Size: 7 inches (1024*600)
- Operation Mode: Tablet Touch Screen
- Connection Method: WiFi Connection
- Battery Capacity: 2500mAh 7.3V
- Charging Method: Adapter Charging
- USB Interface: USB2.0
- WIFI: 2.4G/5G
- Electronic: Yes
- Is Batteries Included: Yes
- Material: Plastic

Figure 15: XTOOL D7W Hardware Configuration
7.2 Software Features
- Special Features: Wifi
- Model Name: XTOOL D7W
- Software Version: 2026
- Hardware Version: 2026
- External Testing Certification: CE
- Item Type: Auto Key Programmer
- ECU Coding: ECU Coding + Hidding Flash
- Diagnostic Level: OE Level Auto Full Systems Diagnostic
- Key Programming: Program key / Key coding
- Control: Bi-Directional Controls
- Reset Functions: 39+ Reset Functions
- OBDII Functions: 10 Full OBDII Functions
- Protocol Support: CAN FD & DOIP Protocol
- Live Data Display: 8 in 1 Live Data Display
- Vehicle Identification: Auto Vin & Auto Scan
- Update Period: 3 years free updates
7.3 Physical Dimensions
- Item Weight: 3kg
- Item Height: 18cm
- Item Width: 2cm
- Item Length: 25cm
- Package Length: 22cm
- Package Width: 33cm
- Package Height: 22cm
7.4 Vehicle Coverage
The XTOOL D7W supports over 88 car makers and 140+ brands, covering 10,000+ cars. It works for 12V Petrol Sedans, SUVs, Minivans, and Light-Duty Trucks globally.
- Europe Cars: DEMO, VW, MINI, LANDROVER, SEAT, FERRARI, FORD, OPEL, ALFA, ROMEO, VOLVO, ABARTH, SMART, BMW, FIAT, LANCIA, RENAULT, ASTONMARTIN, GAZ, MASERATI, MEREDES, UAZ, SKODA, CITROEN, DACIA, AUDI, JAGUAR, PORSCHE, PEUGEOT
- Russian Cars: ZAZ, IZH, PAZ, UAZ, VAZ, GAZ, Lada
- America Cars: DEMO, GM, FORD, CADILLAC, CHEVROLET, GMC, HUMMER, JEEP, SATURN, PONTIAC, LINCOLN, DODGE, CHRYSLER, BUICK
- Asia Cars: Demo, TOYOTA -LEXUS, ISUZU, MAZDA, KIA, INFINITI, ACURA, NISSAN, RENAILTSAM, HYUNDAICY, HYUNDAI, HONDA, SUBARU, SUZUKI, MITSUBISHI, SSANGYONG
- Australia Cars: Demo, Ford, Honda
- China Cars: DEMO, JAC, CHERY, GEELY, GREAT WALL, BYD, LIFAN

Figure 16: XTOOL D7W Vehicle Coverage
Note: Not all models may be supported with all functions. You can check the supported models and functions on the official XTOOL website.
8. Warranty and Support
8.1 Warranty
The XTOOL D7W comes with a 2-year warranty.
8.2 Technical Support
For technical assistance, you can contact Shenzhen Xtooltech Intelligent Co., Ltd. via:
- Official Website: www.xtooltech.com
- Tel: +86 755 21670995 or +86 755 86267858 (China)
- E-mail: supporting@xtooltech.com
- Remote Assistance: Use the built-in TeamViewer QuickSupport application for remote technical support.
9. User Tips
- Fast and Reliable: Users consistently praise the D7W for its speed and reliability in diagnostics and updates.
- Language Support: The device supports 22 languages. If you need a specific language like Russian, ensure it's activated during setup or contact technical support for assistance.
- Customer Service: Technical support is highly responsive and helpful, especially with OS updates and language installations. Don't hesitate to reach out if you encounter issues.
- Material Quality: The device is made of durable plastic and is noted for its high quality, having passed external testing.
- Vehicle Compatibility: While extensive, always verify compatibility for specific functions and your car model on the official XTOOL website or by contacting the seller.
- Updates are Key: Keep your software updated to access the latest features and vehicle models. The 3 years of free updates are a significant benefit.