WELLMEET FUT038

Contents

WELLMEET Mi-Light 4-Zone RGBW LED Controller and Remote Control User Manual

Models: FUT038 (Controller), FUT096 (Remote Control)

1. Product Overview

The WELLMEET Mi-Light 4-Zone RGBW LED Controller (Model FUT038) and its accompanying 2.4GHz RF Remote Control (Model FUT096) provide advanced control over RGBW LED strip lighting. This system allows for wireless control of color, brightness, and dynamic modes across up to four independent zones, offering 16 million colors to choose from.

Mi-Light FUT038 controller and FUT096 remote control

Figure 1: Mi-Light FUT038 Controller and FUT096 Remote Control

Video 1: Unboxing and demonstration of the remote control and LED strip functionality, including battery installation, color changing, mode changing, speed adjustment, and brightness adjustment.

2. Specifications

2.1 FUT038 RGBW LED Strip Controller

FeatureSpecification
Model NumberFUT038
Input VoltageDC12V-24V
Output CurrentMax. 6A/Channel
Total Output CurrentMax. 10A
Control Distance30m
RF Frequency2.4GHz
Output ConnectionCommon Anode
MaterialPLASTIC
Dimensions85mm x 45mm x 22.5mm
CertificationCE, ROHS

2.2 FUT096 4-Zone Touch RF RGBW Remote Control

FeatureSpecification
Model NumberFUT096
Voltage3V (2xAAA batteries)
Transmission Frequency2.4GHz
Modulation MethodGFSK
Transmitting Power6dBm
Standby Power Consumption20uA
Control Distance30m
Size120mm x 52.5mm x 21mm
MaterialPLASTIC
CertificationCE, ROHS

3. Setup

3.1 Installation Precautions

  • This product should be debugged and installed by someone with professional qualifications.
  • This product is not waterproof. It needs to be protected from sunlight and rain. If installed outdoors, please use a waterproof enclosure.
  • Good heat dissipation conditions will extend the service life of LED controllers. Please install the product in a well-ventilated environment.
  • Do not install or use this product in areas with lightning, strong magnetic fields, or high voltage.
  • Please check that the output voltage of the LED power supply used meets the requirements of the product voltage range (DC12V-24V).
  • The diameter and size of the wires used must be sufficient to load the LED lighting fixtures connected, and ensure that the wiring is secure to prevent accidents triggered by heat or poor contact.
  • Before powering on and debugging, it is necessary to ensure that all wiring is correct to avoid damage to the lighting fixtures due to wiring errors.
Installation Precautions for LED Controller

Figure 2: Important installation precautions.

3.2 Wiring Diagram (FUT038 Controller)

The FUT038 controller uses a common anode connection. Connect your 12V-24V RGBW LED strip to the controller's output terminals as shown in the diagram below. Ensure the power supply is connected to the DC input port.

FUT038 Controller wiring diagram showing DC input and LED strip terminals

Figure 3: FUT038 Controller with DC 12-24V input and LED strip terminal connections (V+, W, B, G, R).

3.3 Remote Control Battery Installation (FUT096)

The FUT096 remote control requires two AAA batteries. Open the battery compartment cover on the back of the remote and insert the batteries, ensuring correct polarity. Close the cover securely.

FUT096 Remote control battery compartment for 2xAAA batteries

Figure 4: Remote control battery compartment for 2xAAA batteries.

4. Operating Instructions

4.1 Remote Control Functions (FUT096)

FUT096 Remote control with button labels

Figure 5: FUT096 Remote Control Layout and Functions.

  • Master ON (I) / Master OFF (O): Turns all linked lights ON or OFF.
  • Color Ring: Touch the color ring to select from 16 million colors.
  • Brightness +/-: Adjusts the brightness level of the selected color or mode.
  • Speed +/- (S+, S-): Increases or decreases the speed of dynamic modes.
  • Mode (M): Cycles through various dynamic lighting modes/programs.
  • Zone ON (1, 2, 3, 4): Turns on the corresponding zone.
  • Zone OFF (1, 2, 3, 4): Turns off the corresponding zone.
  • 4x Link/Unlink Light: Used for linking and unlinking the remote with the controller.

4.2 Linking the Remote Control to the Controller

  1. Switch off the LED light/controller you wish to link.
  2. Wait for at least 10 seconds.
  3. Switch on the LED light/controller.
  4. Within 3 seconds of switching on, short press one of the 'Zone ON' buttons (1, 2, 3, or 4) three times.
  5. If linking is successful, the LED light will blink 3 times slowly.

4.3 Unlinking the Remote Control from the Controller

  1. Switch off the LED light/controller you wish to unlink.
  2. Wait for at least 10 seconds.
  3. Switch on the LED light/controller.
  4. Within 3 seconds of switching on, short press the 'Master ON' button (I) five times.
  5. If unlinking is successful, the LED light will blink 10 times quickly.
Linking and Unlinking instructions for Mi-Light remote and controller

Figure 6: Visual guide for linking and unlinking the remote control.

4.4 Grouping Multiple Lights/Controllers

You can add an unlimited number of lights or controllers to a single zone on the 4-channel remote by linking them to the same zone. This allows for flexible control in creating different group configurations. Conversely, one light or controller can be controlled by a maximum of four remotes.

Diagram showing 4-zone control of lights within a house

Figure 7: Example of 2.4GHz wireless transmission for 4-zone group lighting.

5. Maintenance

  • Clean the controller and remote control with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
  • Replace the AAA batteries in the remote control when the indicator light blinks quickly or the remote becomes unresponsive.
  • Ensure the controller is kept in a well-ventilated area to maintain good heat dissipation.

6. Troubleshooting

  • Remote not responding: Check if the batteries are correctly installed and have sufficient power. Replace if necessary. Ensure the remote is within the 30m control distance. Try re-linking the remote to the controller.
  • Light not blinking quickly during unlinking: If the light does not blink quickly after attempting to unlink, switch off the light again, wait 10 seconds, and repeat the unlinking steps carefully.
  • Remote indicator light blinking quickly: This indicates a low battery or the use of poor quality batteries. Replace with fresh AAA batteries.
  • Intermittent control or poor range: The 2.4GHz RF remote control system is a precise electronic product. Avoid installing or using it in areas with strong magnetic fields, high voltage, or excessive humidity. Ensure the environment is indoor and dry.
  • LED strip not lighting up or incorrect colors: Verify all wiring connections are secure and correct (common anode, V+, R, G, B, W). Check that the power supply voltage matches the controller's requirements (DC12V-24V). Ensure the LED strip itself is functional.

7. Warranty and Support

Our LED controller products come with lifelong technical support and warranty services.

7.1 Free Warranty

If any quality issues occur within two years from the date of purchase, our company will provide free repair, service, or replacement. The company's maximum responsibility for factory products is to replace them with products of the same model and quantity.

7.2 Paid Warranty

Products that exceed the free warranty period will be charged a certain cost for repair materials.

7.3 Exclusions from Free Warranty

The following situations are not covered under free warranty or replacement services:

  • Damage caused by excessive voltage, overload, or improper operation.
  • Any wiring errors, water immersion (for non-waterproof products), and unauthorized repairs.
  • Any serious damage or deformation to the appearance caused by transportation or knocking.
  • The product appearance is severely damaged or deformed.
  • Damage caused by natural disasters and uncontrollable human factors, such as earthquakes, floods, fires, etc.

7.4 Repair Process

To expedite the repair or replacement process, please provide a detailed description of the fault phenomenon, the operating environment, and any actions taken prior to contacting support. The logistics cost of returning the product for repair will be borne by the customer.

After-Sales Service details including warranty terms and exclusions

Figure 8: Detailed After-Sales Service information.

8. User Tips

  • Multi-Room Control: If you have multiple controllers and remotes, each remote can be programmed to control a specific LED setup in a different room, allowing for independent lighting control throughout your home.
  • Remote Sensitivity: When installing batteries into the remote, keep your finger off the touch color ring to improve its sensitivity and ensure proper calibration.
  • Flexible Re-programming: The system allows for easy re-programming as needed. One remote can control countless lamps or controllers, but one lamp or controller can only be controlled by a maximum of four remotes.
  • Power Cycle for Reset: If you encounter issues, a quick power cycle (turning the light off and on again) can sometimes resolve minor glitches before attempting to re-link.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.