1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your 36V350W17A Electric Scooter Universal Controller Kit. This kit is designed for 10-inch scooters, offering enhanced control and smart features via a dedicated mobile application. Please read this manual thoroughly before use to ensure safe and optimal performance.
2. Safety Information
⚠️ Please mind potential fire risk and strictly follow the instruction manual for charging and storage.
- Reversing the positive and negative terminals is strictly prohibited, as it will immediately burn out the controller.
- Ensure all terminals are fully inserted and securely connected to prevent short circuits or poor contact.
- The controller must operate within the specified voltage range; do not exceed the rated voltage.
- The controller's power rating must match the motor's power rating—do not use an undersized controller for an oversized motor.
- Do not use or store the controller in damp, high-temperature, or flammable/explosive environments.
- Installation should be performed by qualified personnel with electrical expertise. Non-professionals must not disassemble or attempt repairs.
3. Product Specifications
| Attribute | Value |
|---|---|
| Product Name | 10-inch Electric Scooter Controller Kit |
| Rated Voltage | DC 36V |
| Current Limit | 17A ± 0.5A |
| Compatible Motor Power | 350W |
| Battery Connector | XT60 |
| Max Speed | 40km/h |
| Key Features | Speed Control, Cruise Control, Self-Diagnostic, Low Voltage Protection, Bluetooth with APP |
| Authentication | CE |
4. Package Contents
The XFY-Max10 Inch Controller Kit typically includes the following components:
- Universal Controller (36V350W17A)
- Display Screen / Dashboard
- Communication Line
- Accelerator Wire
- Headlight Wire
- Brake Wire
- XT60 Battery Wire
- HY Hall Wire
- Test Wire
- Headlight
- Taillight

5. Setup & Installation
Installation should be performed by qualified personnel with electrical expertise. Ensure the scooter is powered off and the battery is disconnected before beginning installation.
5.1. Controller Wiring Diagram

5.2. Dashboard Wiring Diagram

5.3. Motor Self-Learning Methods
If your motor does not rotate or reverses incorrectly, follow these steps for self-learning. The actual situation of the motor shall prevail. Note that due to varying motor characteristics, the no-load maximum speed may not always reach the control settings.
- Rack the motor (lift the wheel off the ground).
- Grab the brake handle (ensure brake is set to maximum).
- Turn on the motor.
- Adjust the speed control handle from zero to maximum, 3 times in a row. The meter will display 'Fx' or '-x' (where x=0-5) after this operation.
- Release the brake handle and speed control handle. The motor will automatically rotate for a few seconds and then stop. If it does not rotate, immediately shut down the machine and re-operate.
- Adjust the speed control handle to the maximum to check if the motor rotation direction is correct. If correct, release the speed control handle to let the motor skid to a stop (do not brake) to complete the study, then turn off the power. If incorrect, proceed to the next step.
- If the motor rotation direction is not correct, release the speed control handle and wait for the motor to stop. Grab the brake (adjusted to maximum), adjust the speed control handle from zero to maximum 1 time, then release the brake and speed control handle. At this point, the meter will change from 'F' to '-' or from '-' to 'F'.
- Adjust the speed control handle to the maximum to see whether the motor rotation direction is correct. If it is correct, then release the speed control handle and let the motor coast to a stop (do not brake) to complete the study and then turn off the power. If it is not correct, repeat step 7.
5.4. Hall Line and Phase Line Adjustment
If your scooter does not run well (e.g., noise, not smooth, motor shake but no run, speed not reaching 15 km/h), you may need to adjust the Hall line or Phase line connections. The diagrams below illustrate various connection methods.

6. Operating Instructions
6.1. Dashboard Function Description

- Power On/Off: Press and hold the “on/off” button to power on or off. A “beep” sounds upon startup. The device automatically powers off after ten minutes of inactivity.
- Lights Control: Press the “on/off” button once to toggle the front and rear lights on or off. The rear lights flash when braking (regardless of whether the lights are on).
- Mode Switching: Double-press the “on/off” button with a “beep” to switch modes:
- Mode 1 (ECO): 0-10 km/h
- Mode 2 (D): 0-20 km/h
- Mode 3 (S): 0-30 km/h (Speed display turns pink in Mode 3, default S mode).
- Unit Display (km/h / mph): Press the "on/off" button three times with a 'beep' sound to switch between km/h and mph display (default km/h). After switching to mph, the speeds for Gears 1, 2, and 3 are “6mph, 12mph, 18mph” respectively.
- Cruise Control: Press the “on/off” button four times. The buzzer will beep to activate or deactivate cruise control. When cruise control is active, holding the throttle for 10 seconds engages cruise mode. The buzzer will beep, the cruise icon will illuminate, and the mode will exit upon subsequent throttle/brake operation, gear shifting, or light activation (default: enabled). Note: The icon remains off when cruise control is inactive, flashes when activated, and stays lit during cruise operation.
- Start Mode: Press the “on/off” button five times. The buzzer will beep once to toggle between zero-start and non-zero-start modes (default: non-zero-start).
- Reset Total Mileage: Press the “on/off” button nine times. The buzzer will beep once to reset the total mileage.
- Bluetooth Unpairing: To unpair Bluetooth, simultaneously press and hold the “Brake” and “On/Off” buttons until the display shows “UC” during startup.
6.2. Bluetooth Functionality and App Instructions
The controller features memory function and Bluetooth capability. The Bluetooth name is “MAX”. The Bluetooth icon remains off when unconnected and stays on when connected. When locked via the app, the display shows “LC”.
- Download App: Scan the QR code on the specification sheet (or product packaging) to download the “Tuya Smart” app, or search for it in your app store.
- App Permissions (Android): After downloading and installing, Android users must enable all permissions for the Tuya Smart app in (System Settings > Application Settings) to control the vehicle via the app.
- Pairing: Open the app, tap Add Device, enable Auto-discovery in the top-right corner, search for the “MAX” device via Bluetooth, then add and complete.
- Unlock Motor: Tap "Unlock Motor” (with the scooter powered on). The app interface will display vehicle information and complete Bluetooth pairing. Once paired successfully, vehicle details will be saved for automatic reconnection next time.
- App Functions: The app allows you to:
- Switch between zero-start and non-zero-start modes.
- Enable cruise control.
- Change gears.
- Switch between metric and imperial units in More Settings.
- View current voltage in More Settings.
- Turn on headlights.
- After tapping the central map to start riding, display real-time location, riding time, current trip distance, and average speed.
- Lock the bike via the app interface's lock button to disable motor rotation.
- Tap the upper-right corner of the app interface to clear device data.



6.3. Battery Level Display (±0.5V)
- Five-bar: 40.5V–42.0V
- Four-bar: 38.5V–40.4V
- Three-bar: 36.5V–38.4V
- Two-bar: 35.5V-36.4V
- One-bar: 33.5V-35.4V
Low voltage alarm triggers when battery voltage drops below 33.5V; battery icon flashes one bar. Under-voltage protection activates when battery voltage falls below 31V; motor stops, instrument displays E7 error, and battery level indicator turns off.
7. Maintenance
- Regularly check all wiring connections to ensure they are secure and free from damage.
- Keep the controller and display clean and dry. Avoid exposure to water or excessive moisture.
- Store the scooter and controller in a dry, cool environment, away from direct sunlight and extreme temperatures.
- Do not attempt to open or repair the controller yourself. Refer to qualified technicians for any issues.
8. Troubleshooting
8.1. Fault Warning Code Explanation
| Code | Description |
|---|---|
| E2 | Throttle Fault |
| E3 | Brake Failure |
| E4 | MOS Failure, Overcurrent Protection |
| E5 | Hall Sensor Failure |
| E6 | Stall Protection / Locked Rotor Protection |
| E7 | Undervoltage Protection |
| E8 | Overvoltage Protection |
| E9 | Communication Failure |
8.2. Motor Issues
- Motor shake, vibrates but doesn't run: This indicates a Hall line issue. Refer to section 5.4 for Hall line adjustment methods.
- Motor runs smoothly but in reverse: This indicates a Phase line issue. Refer to section 5.4 for Phase line adjustment methods.
- Speed can't reach higher than 15 km/h: After trying all Hall/Phase line combinations, if speed is still limited, it might be due to compatibility between the controller and your specific motor.
9. User Tips
- Compatibility: This controller is designed for 10-inch scooters and is compatible with models like MAX G30. For other models such as Foston S8 Pro, Xiaomi M365 (250W), or Aovopro Esmax, verify compatibility with the seller or a qualified technician before purchase and installation.
- Speed Unlock: While the app allows setting speeds up to 40 km/h, actual achievable speed may vary based on motor compatibility and scooter configuration. If the scooter shows a maximum of 30 km/h despite app settings, further adjustments or motor compatibility checks might be needed.
- Test Wire: The 'Test Wire' on the controller (Figure 2) is typically used for diagnostic purposes or initial setup to verify motor rotation. Consult a technician if unsure about its use.
10. Warranty & Support
For any product quality or infringement issues, the manufacturer/importer/seller shall be solely held responsible. Please contact your seller for specific warranty details and support.
For additional guidance, you may refer to the official user manual PDF: User manual (PDF)
