1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your 36V 350W Electric Scooter Universal Controller and Display Kit. This kit is designed for 10-inch electric scooters, including models like the MAX G30, and features APP connectivity for enhanced control. Please read this manual thoroughly before installation and use to ensure safe and optimal performance.
2. Safety Information
⚠️ Please read and adhere to all safety warnings to prevent injury or damage to the product.
- Fire Risk: Please mind potential fire risk and strictly follow the instruction manual for charging and storage.
- Polarity: Reversing the positive and negative terminals is strictly prohibited, as it will immediately burn out the controller.
- Connections: Ensure all terminals are fully inserted and securely connected to prevent short circuits or poor contact.
- Voltage Range: The controller must operate within the specified voltage range; do not exceed the rated voltage.
- Power Matching: The controller's power rating must match the motor's power rating—do not use an undersized controller for an oversized motor.
- Environment: Do not use or store the controller in damp, high-temperature, or flammable/explosive environments.
- Installation: Installation should be performed by qualified personnel with electrical expertise. Non-professionals must not disassemble or attempt repairs.
3. Product Specifications
| Feature | Specification |
|---|---|
| Product Name | 10-inch Electric Scooter Controller Kit |
| Rated Voltage | DC 36V |
| Current Limit | 17A ± 0.5A |
| Compatible Motor Power | 350W |
| Battery Connector | XT60 |
| Hall Wire Type | HY Hall Wire |
| Max Speed | 40km/h |
| Key Features | Speed Control, Cruise Control, Self-Diagnostic, Low Voltage Protection, APP Control, Bluetooth |
| Origin | Mainland China |
| Authentication | CE |
Package Contents:
The kit typically includes:
- Controller unit
- Dashboard display unit
- Communication line
- Accelerator wire
- Headlight wire
- Brake wire
- Taillight
- Test wire
- QR code for Tuya APP download
Image: Typical 7-piece controller kit components, including controller, dashboard, and various wires.
Image: Typical 4-piece controller kit components.
Image: Controller kit with Tuya Smart APP QR code for download.
4. Setup & Installation
4.1. Controller Wiring Diagram
Carefully connect the controller to your scooter's components according to the diagram below. Ensure each connection is secure and matches the labeled wires.
Image: Controller wiring diagram showing connections for Communication line, Motor three-phase line, XT60 Battery Wire, HY Hall Wire, Taillight, and Test Wire.
4.2. Dashboard Wiring Diagram
Connect the dashboard display unit as shown in the diagram. Pay attention to the communication, accelerator, headlight, and brake wire connections.
Image: Dashboard wiring diagram indicating Communication line, Accelerator Wire, Headlight Wire (Yellow '+'), and Brake Wire.
4.3. Motor Self-Learning Methods
If your motor does not rotate or reverses, follow these steps for self-learning. The actual situation of the motor may vary.
- Rack the motor (lift the wheel off the ground).
- Grab the brake handle (ensure brake is set to maximum).
- Turn on the motor.
- Adjust the speed control handle from zero to maximum, 3 times in a row. The display will show Fx or -x (x=0-5) after this operation.
- Release the brake handle and speed control handle. The motor will automatically rotate for a few seconds and then stop. If it does not rotate, immediately shut down the machine and re-operate.
- Adjust the speed control handle to the maximum to check if the motor rotation direction is correct. If it is correct, release the speed control handle, let the motor skid to a stop (do not brake), and then turn off the power. If incorrect, proceed to step 7.
- If the motor rotation direction is not correct: Release the speed control handle and wait for the motor to stop. Grab the brake (brake adjusted to the maximum). Adjust the speed control handle from zero to the maximum, 1 time. Release the brake and the speed control handle. At this time, the display will change from F to - or - to F.
- Adjust the speed control handle to the maximum to see whether the motor rotation direction is correct. If it is correct, then release the speed control handle and let the motor coast to a stop (do not brake) to complete the study and then turn off the power. If it is not correct, then repeat step 7.
4.4. Motor Troubleshooting: Hall Line and Phase Line Adjustment
If your scooter motor is not running well, refer to the following adjustments:
Case A: Noise, not smooth, motor shake, vibrates but doesn't run, or speed is below 15 km/h.
Adjust the Hall line. Test the 6 methods below one by one and choose the smoothest operation.
Image: Diagram illustrating Hall line and Phase line connections for an 8.5/10 inch motor. Y=Yellow, G=Green, B=Blue.
Hall Wire Combinations:
- 1. Y-Y, G-G, B-B
- 2. Y-Y, G-B, B-G
- 3. Y-G, G-Y, B-B
- 4. Y-G, G-B, B-Y
- 5. Y-B, G-Y, B-G
- 6. Y-B, G-G, B-Y
Case B: Motor runs smoothly but in reverse.
Adjust the Phase line. Change the wire connection according to the diagram above until it runs correctly.
Phase Wire Combinations:
- 1. Y-Y, G-G, B-B
- 2. Y-Y, G-B, B-G
- 3. Y-G, G-Y, B-B
- 4. Y-G, G-B, B-Y
- 5. Y-B, G-Y, B-G
- 6. Y-B, G-G, B-Y
5. Operating Instructions
5.1. Dashboard Functions
The dashboard display provides essential information and control over your scooter. Refer to the diagram and functions below:
Image: Dashboard display showing Speed unit (km/h, mph), Gear (ECO, D, S), Headlamp, Bluetooth, Battery Icon, and On/off key.
- Power On/Off: Press and hold the "on/off" button to power the scooter on or off. A "beep" sound will confirm startup. The device automatically powers off after ten minutes of inactivity.
- Lights Control: Press the "on/off" button once to toggle the front and rear lights on or off. The rear lights will flash when braking, regardless of whether the lights are on.
- Mode/Gear Switching: Double-press the "on/off" button (with a "beep") to switch between riding modes:
- Mode 1 (ECO): 0-10 km/h
- Mode 2 (D): 0-20 km/h
- Mode 3 (S): 0-30 km/h (Speed display turns pink in Mode 3)
- Unit Switching (km/h / mph): Press the "on/off" button three times (with a 'beep' sound) to switch between km/h (default) and mph. When in mph, the speeds for Gears 1, 2, and 3 are approximately 6mph, 12mph, and 18mph respectively.
- Cruise Control: Press the "on/off" button four times. A buzzer will beep to activate or deactivate cruise control. When active, holding the throttle for 10 seconds engages cruise mode. The buzzer will beep, the cruise icon will illuminate, and the mode will exit upon subsequent throttle/brake operation, gear shifting, or light activation (default: enabled). The icon remains off when cruise control is inactive, flashes when activated, and stays lit during cruise operation.
- Start Mode (Zero-start / Non-zero-start): Press the "on/off" button five times. A buzzer will beep once to toggle between zero-start and non-zero-start modes (default: non-zero-start).
- Clear Total Mileage: Press the "on/off" button nine times. The buzzer will beep once to reset the total mileage.
5.2. Battery Level Display
The dashboard displays battery level with bars, corresponding to voltage ranges:
- Five-bar: 40.5V–42.0V
- Four-bar: 38.5V–40.4V
- Three-bar: 36.5V–38.4V
- Two-bar: 35.5V-36.4V
- One-bar: 33.5V-35.4V
A low voltage alarm triggers when battery voltage drops below 33.5V (battery icon flashes one bar). Undervoltage protection activates when battery voltage falls below 31V, causing the motor to stop, the instrument to display an E7 error, and the battery level indicator to turn off.
5.3. Bluetooth Functionality and App Instructions
The controller kit supports Bluetooth connectivity via the "Tuya Smart" app.
- Download App: Scan the QR code provided in the package or search for "Tuya Smart" in your app store.
- Permissions (Android Users): After downloading and installing, enable all necessary permissions for the Tuya Smart app in your device's System Settings > Application Settings to control the vehicle.
- Pairing: Open the app, tap "Add Device", enable "Auto-discovery" in the top-right corner, search for the "MAX" device via Bluetooth, then add and complete the pairing process.
- Unlock Motor: Tap "Unlock Motor" in the app (with the scooter powered on). The app interface will display vehicle information and complete Bluetooth pairing. Once paired, vehicle details will be saved for automatic reconnection.
- App Controls: The app allows you to:
- Switch between zero-start and non-zero-start modes.
- Enable cruise control.
- Change gears.
- Switch between metric and imperial units (in More Settings).
- View current voltage (in More Settings).
- Turn on headlights.
- Display real-time location, riding time, current trip distance, and average speed after tapping the central map to start riding.
- Lock the bike via the app's lock button, which disables motor rotation.
- Clear device data by tapping the upper-right corner of the app interface.
- Bluetooth Unpairing: To unpair Bluetooth, simultaneously press and hold the "Brake" and "On/Off" buttons during startup until the display shows "UC".
- Speed Limit Adjustment: You can adjust speed limits for gears 1, 2, and 3 via the app's advanced settings. After disabling the limits, gear speeds become 5-15 km/h, 15-25 km/h, and 20-40km/h respectively. The current speed settings will be retained after adjustment via the app.
Image: Tuya Smart App ETC settings screen showing unit, battery status, and voltage.
Image: Tuya Smart App Bluetooth connection screen, showing 'COMMON' device connected.
Image: Tuya Smart App screen for selecting power levels (dp_level_level_1 to dp_level_level_5).
6. Maintenance
To ensure the longevity and optimal performance of your controller kit, consider the following general maintenance tips:
- Regularly check all wire connections for tightness and signs of wear or damage.
- Keep the controller and display unit clean and free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning.
- Avoid exposing the components to extreme temperatures or direct sunlight for prolonged periods.
- If any component appears damaged, consult a qualified technician for repair or replacement. Do not attempt to repair complex internal components yourself.
7. Troubleshooting
The display unit may show error codes if a fault occurs. Refer to the list below for common error codes and their meanings:
| Error Code | Description |
|---|---|
| E2 | Throttle Failure |
| E3 | Brake Failure |
| E4 | MOS Failure, Overcurrent Protection |
| E5 | Hall Sensor Failure |
| E6 | Stall Protection (Locked Rotor Protection) |
| E7 | Undervoltage Protection |
| E8 | Overvoltage Protection |
| E9 | Communication Failure |
For detailed motor troubleshooting regarding Hall line and Phase line adjustments, refer to Section 4.4.
8. User Tips
- Wheel Size Adjustment: The Tuya Smart app may offer settings to adjust the wheel size (e.g., from 10 inches to 8.5 inches). This can be crucial for accurate speed readings and overall scooter performance. Check the 'More Settings' section within the app for this option.
- Initial Setup: Take your time during the initial wiring and motor self-learning process. Incorrect connections or an improperly calibrated motor can lead to performance issues or damage.
- App Exploration: Explore all features within the Tuya Smart app, as it provides advanced controls and monitoring capabilities for your scooter.
9. Warranty and Support
For warranty information and technical support, please refer to the seller's policies or contact the manufacturer directly. Keep your purchase receipt as proof of purchase.
A PDF version of the user manual may be available for download. Please check the product page or contact customer support for the link.
Image: Certificate of Conformity for the Electric Scooter Controller.