Flytec GPS RC Fishing Bait Boat Remote Control User Manual

1. Introduction

This manual provides instructions for the Flytec V900-04 Remote Control, designed as an original spare part for Flytec GPS RC Fishing Bait Boats models V010, V020, V070, and V900. Please read this manual carefully before use to ensure proper operation and maintenance.

2. Specifications

3. Setup and Pairing

This remote control is specifically designed for Flytec V010, V020, V070, and V900 original model boats. It must be paired with the corresponding boat circuit board. Using it with other circuit boards may result in malfunction.

3.1 Compatible Boat Circuit Boards

Ensure your boat uses one of the following original circuit boards:

• V010 Boat Circuit Board:



• V020 Boat Circuit Board:



• V070 Boat Circuit Board:



• V900 Boat Circuit Board:



Additionally, ensure the boat's circuit board has the correct connections for the GPS module, lights, battery, servo, and motors. An example of a compatible circuit board layout is shown below:



3.2 Pairing Instructions

Follow these steps to pair the remote control with your boat's circuit board:

1. Place the boat on a dry, flat surface. Do NOT place it in water during pairing.
2. Connect the boat battery and install batteries into the remote control.
3. Perform frequency matching:

   

   • Press and hold the pairing button on the remote control (do not release).
   • While holding the pairing button, turn on the power switch on the boat.
   • Then, turn on the power switch on the remote control.
   • The remote control will emit a "beep" sound, and the green indicator light on the boat will turn on, indicating successful pairing.
4. After successful pairing, press any button on the remote control. The boat's lights will flash. Once the boat lights stop flashing, the boat is ready for use.

4. Operating Instructions

This section describes the general operation of the remote control. Specific functions may vary slightly depending on the boat model (V010/V020/V070/V900).

• GPS Button: Activates/deactivates GPS functions (e.g., auto-navigation, return-to-home). Refer to your boat's specific manual for detailed GPS features.
• Power Switch: Turns the remote control ON/OFF.
• Joysticks: Control the boat's movement (forward, backward, left, right).
• Numbered Buttons (1, 2, 3, 4): These typically correspond to bait release mechanisms or other programmable functions on the boat. Consult your boat's manual for exact assignments.
• Directional Pad (Right side): Used for menu navigation on the LCD screen or fine-tuning certain settings.
• LCD Screen: Displays information such as signal strength, battery level, GPS status, and other operational data.

5. Maintenance

• Cleaning: Wipe the remote control with a soft, dry cloth. Do not use harsh chemicals or solvents.
• Storage: Store the remote control in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries if storing for extended periods to prevent leakage.
• Battery Replacement: Replace batteries when the low battery indicator appears on the LCD screen or when performance degrades. Ensure correct polarity when inserting new batteries.
• Avoid Water Exposure: While designed for use with bait boats, the remote control itself is not waterproof. Avoid direct contact with water.

6. Troubleshooting

Problem: Remote control does not power on.

Solution: Check if batteries are correctly installed and fully charged. Replace with new batteries if necessary.

Problem: Boat and remote control cannot pair.

Solution:

• Ensure the boat is turned on first, then the remote control.
• Keep the boat and remote control within 50 cm of each other during the pairing process.
• Verify that you are pressing and holding the pairing button on the remote control while turning it on.
• Confirm that your boat model (V010/V020/V070/V900) is compatible with this remote control and uses an original Flytec circuit board.
• Refer to the "Pairing Instructions" in Section 3.2.

Problem: Boat does not respond to remote control commands after pairing.

Solution:

• Check the boat's battery level.
• Ensure there are no strong interference sources nearby.
• Re-attempt the pairing process as described in Section 3.2.

Problem: GPS alarm 44H displayed.

Solution: This alarm typically indicates a GPS signal issue. Ensure the boat is in an open area with a clear view of the sky. Allow sufficient time for the GPS module to acquire satellites. If the issue persists, consult the boat's specific manual or contact Flytec support.

7. User Tips

• Compatibility Check: Always double-check that your boat model (V010, V020, V070, V900) is listed as compatible before attempting to use this remote control. This remote is designed for original Flytec circuit boards only.
• Pairing Distance: For best results during pairing, keep the remote control and the boat close to each other (within 50 cm).
• Battery Management: Use fresh, high-quality batteries for the remote control to ensure stable operation and prevent unexpected disconnections.
• GPS Signal: If your boat has GPS functionality, ensure it's used in an open environment for optimal satellite reception.

8. Warranty and Support

For warranty information, technical support, or replacement parts, please contact Flytec Official Store or your original point of purchase. Keep your purchase receipt as proof of purchase.

Manufacturer: Flytec

Origin: Mainland China

Certification: CE