1. Product Overview
The GODIAG GD101 (Vehicle Network Communication Interface) is a device that works between diagnostic software and a vehicle. It is compatible with J2534 Passthru and ELM327 standards. It performs offline key and IMMO instrument synchronization tests, intelligent IMMO system emergency start area sensing detection, IMMO dashboard offline diagnosis, instrument IMMO data reading and writing, instrument mileage repair, and key matching. It supports VW, Skoda, Seat, and other models.
Functions:
- Offline connection to the dashboard to convert to standard OBD2.
- Perform key chip and instrument synchronization test.
- Independent ignition switch.
- Key induction adapter with light.
Product Highlights:
- Supports most J2534 compatible software (HDS, TIS, ODIS, JLR SDD, PCM...).
- Supports most ELM327 software (ELMConfig, Forscan, ScanMaster...).
- Supports ECU reprogramming in J2534 mode with programming voltage.
- Supplies free software for diagnosing J1979 compatible vehicles.
- Supports Windows 8/10/11, 32/64bit.
Supported Languages of Compatible Software:
- ODIS software: English, Japanese, Portuguese, Romanian, Korean, Dutch, Polish, Turkish, Spanish, French, Italian, Croatian, Danish, German, Swedish, Finnish, Slovenian, Czech, Russian, Greece, Chinese.
- For Toyota Techstream software: English, French, Spanish, Japanese, German, Italian, Russian, Turkish, Chinese.
- For Honda HDS software: English, German, Czech, Dutch, Finnish, French, Greek, Hungarian, Italian, Norwegian, Polish, Portuguese, Russian, Slovenian, Spanish, Swedish, Turkish, Japanese, Chinese.
- JLR SDD software: German, English, Spanish, French, Italian, Dutch, Portuguese, Russian, Japanese, Chinese, Korean.
- Forscan software: English, Russian, Polish, Italian, German, Hungarian, Turkish, French, Latvian, Bosnian, Finnish, Romanian, Portuguese, Traditional Chinese, Simplified Chinese, Czech, Lithuanian, Slovak, Ukrainian.
- Scanmaster ELM327 software: English, Czech, German, Spanish, French, Hungarian, Italian, Polish, Serbian, Turkish, Danish, Croatian.
- PCM-Flash software: English, Russian.
Note for PCM-Flash 1.20: Customers need to buy a dongle (pcmtuner dongle), and it only supports the OBD part. It does not support bench, boot, VAG, DSG, and gearboxes.
2. Setup and Installation
This section guides you through the installation of necessary software and drivers for your GODIAG GD101 device.
Software and Driver Installation (JLR SDD Example)
The following video demonstrates the installation process for JLR SDD2 software and the GODIAG J2534 driver. Please follow the steps carefully.
Video: JLR SDD2 and GODIAG J2534 Driver Installation Guide.
- Download Software and USB Driver: Obtain the necessary software and USB drivers from the official GODIAG website or the provided QR code.
- Install SDD Software: Run the SDD setup file (e.g., SDD-163.00_FULL.exe). Select your preferred language (e.g., English) and accept the license agreement. Acknowledge any firewall compatibility warnings.
- Install HV Safety Installer: During the SDD installation, you may be prompted to install 'HV Safety Installer'. Proceed with its installation.
- Install MOXA UPort Driver: The setup may also prompt for the installation of 'MOXA UPort 1110/1130/1150 Windows Driver'. Install this driver as well.
- Install GODIAG J2534 Driver: Run the GODIAG J2534 driver setup file (e.g., GODIAG DriverSetup_vc_x86_1v0.exe). Select English and proceed with the installation, ensuring 'VS2022 Redistributable Package' is also installed if prompted.
- Apply SDD Patch: After installing the main SDD software, navigate to the 'SDD_Patch' folder. Run 'JLR.SDD.Offline' and 'JLR.SDD.Offline.Fix.2020.7.14' applications.
- Restart Computer: After all installations are complete, restart your computer as recommended by the setup wizard.
- Verify Driver Installation: Connect the GODIAG GD101 device to your computer. Open 'Device Manager' (Right-click 'This PC' -> 'Manage' -> 'Device Manager'). Under 'Ports (COM & LPT)', you should see 'USB Serial Device (COMx)' indicating successful driver installation.
3. Operating Instructions
This section provides guidance on how to use your GODIAG GD101 device for vehicle diagnostics and key matching.
General Usage Steps:
- Download the specific diagnostic software (e.g., JLR SDD, VVDI2, Forscan) and the GODIAG J2534 USB driver onto your computer.
- Connect the GODIAG GD101 OBD2 USB adapter to your vehicle's OBD2 port and to your computer's USB port.
- Turn the vehicle ignition ON.
- Access your chosen J2534/ELM327-based software to perform diagnostics or programming.

Key Matching for VW Golf IV 1999 VDO-93C86 (Example using VVDI2)
- Connect Hardware: Connect the GODIAG GD101, VVDI2, instrument panel, and laptop as shown in the figure below.
- Observe Key Recognition: If the IMMO light on the instrument flashes, it means the instrument has not recognized the key. If the induction adapter flashes for three seconds and then turns off, it also means the key has not been recognized or the key chip does not match.
- Open VVDI2 Software: Launch the VVDI2 software on your laptop.
- Select Instrument Cluster: In VVDI2, navigate to "VW" > "K-Line Instrument/Immobox" > "Instrument Cluster (VDO66, VDO86, Motometer)" > "Read EEPROM" > "Save File".
- Save EEPROM Data: Save the read EEPROM data to a file.
- Select Transponder Programmer: In VVDI2, select "Transponder Programmer".
- Load EEPROM Dump: Select "Load EEPROM dump" and choose the VDO86 eeprom file you just saved.
- Make Dealer Key: Select "Make Dealer Key" > "VVDI Super chip - Select used position. NO NEED write EEPROM".
- Insert Xhorse VVDI Super Chip: Follow the prompts to insert an Xhorse VVDI super chip into the device. If the chip has been used, it needs to be erased first.
- Test Newly Generated Chip: Put the newly generated chip into the induction adapter. After pressing the ignition switch, the light on the induction adapter should flash quickly and then go out immediately, and the IMMO flash quickly and then go out immediately. This indicates that the chip is matched successfully.








Intelligent IMMO System Emergency Start Area Induction Detection:
Press the vehicle's start switch and bring the device's key identifier close to a certain area. If the key identifier light flashes or lights up, it means that the area is the vehicle's key emergency start sensing area. If the customer's smart key is out of power, just put the dead smart key in the key emergency start sensing area to start the vehicle.
4. Maintenance
- Keep the device clean and free from dust and moisture.
- Store the device in a cool, dry place when not in use.
- Avoid dropping or subjecting the device to strong impacts.
- Do not attempt to disassemble or repair the device yourself, as this will void the warranty.
5. Troubleshooting
Car IMMO Start and Start Key Chip Detection - Test Result Analysis:
- Scenario 1: The light of the key identifier flashes and then goes out. This indicates that the IMMO chip and the chip key are working properly.
- Scenario 2: The light of the key identifier flashes for a long time. This indicates that the chip key and the vehicle's IMMO system do not match, and the chip key needs to be re-matched.
- Scenario 3: The light of the key identifier does not flash. This means that the vehicle's IMMO system is faulty. Please check the vehicle's IMMO system.
Common Issues & Solutions:
- Software Compatibility: Ensure you are using the correct version of diagnostic software compatible with J2534 Passthru or ELM327. Some users reported success with specific versions like Techstream v17, Honda HDS 3.105.034, and Forscan.
- Driver Installation: Verify that all necessary drivers (GODIAG J2534 driver, MOXA UPort driver, etc.) are correctly installed and recognized by your operating system (Windows 8/10/11, 32/64bit). Check Device Manager for 'USB Serial Device (COMx)'.
- CAN FD Protocol: The device does not support CAN FD protocol for J2534 VAG.
- Ignition Switch Voltage Detection: The device does not support ignition switch voltage detection for J2534 VAG.
- Medium Speed CAN: The device cannot handle 3, 11 medium speed CAN for Forscan.
- PCM-Flash Limitations: For PCM-Flash 1.20, a separate dongle is required, and it only supports the OBD part, not bench, boot, VAG, DSG, or gearboxes.
- MS-CAN Support: The device does not support MS-CAN.
6. Specifications
| Attribute Name | Attribute Value |
|---|---|
| Brand Name | GODIAG |
| Model Name | SP421-B |
| Hardware Version | Diagnose tool |
| Software Version | NO |
| Item Type | Other |
| Material | Plastic |
| Origin | Mainland China |
| External Testing Certification | CE |
| Voltage | V (Vehicle voltage requirements: 8-18V DC) |
| Power (W) | W |
| Item Length | 14.5 cm |
| Item Width | 10 cm |
| Item Height | 4 cm |
| Item Weight | 0.13 kg |
| High-concerned chemical | None |
| Electronic | No |
| Is Batteries Included | No |
J2534 Protocol Configuration:
- ISO15765 (Standard/Extended frame)
- ISO9141
- ISO14230
- J1850 PWM (Support IFR and 2X speed mode)
- J1850 VPW (Support 4X speed mode)
- Programming voltage
- Short to ground
- ELM327 with command set version 1.3a
J2534 Hardware Configuration:
- ISO11898-2 high speed CAN (OBDII PIN 6 and PIN 14. Speed up to 1000Kbps).
- ISO9141 and ISO14230 K line (OBDII PIN 7 and PIN 15).
- J1850 PWM (OBDII PIN 2 and PIN 10).
- J1850 VPW (OBDII PIN 2).
- Programming voltage (OBDII PIN 12 or PIN 13. Programming voltage up to 20V).
- Short to ground (OBDII PIN 9. Short to OBDII PIN5).
- Dimension (L*W*H): 95mm*55mm*23mm.
- Environmental: -20℃-45℃ (-4℉-113℉).
- Vehicle voltage requirements: 8-18V DC.
- Vehicle connection: Molded DLC3 (OBDII-16).
- Host connection: USB 2.0.
7. User Tips
- Many users have successfully used the GODIAG GD101 with various diagnostic software like Forscan, Techstream, and Honda HDS. Ensure you have the correct software versions and drivers installed.
- For VW/Audi/Seat vehicles, note that the device supports J2534 VAG only and does not support CAN FD protocol or ignition switch voltage detection.
- When using PCM-Flash, remember that a separate dongle is required, and functionality is limited to the OBD part.
- If experiencing issues with key recognition, ensure the key chip is correctly matched or re-matched using the appropriate software.
- For optimal compatibility, some users recommend setting up a dual-boot Windows 10 system for specific diagnostic software like ODIS.
8. Accessories
- 1pc x GODIAG GD101 J2534 Diagnostic Interface
- 1pc x User Manual (PDF)
9. Warranty and Support
For technical support, product inquiries, or warranty information, please contact GODIAG directly:
- Website: www.godiag.com
- Phone: +86 18813687743
- Email: Sales@GoDiag.com
Shenzhen Sinoy Technology Co.,Ltd holds all rights reserved for this product.