XINJE XD5-24T-E

Contents

XINJE XD5 Series XD5-24T-E PLC Industrial Controller User Manual

Model: XD5-24T-E

1. Introduction

This manual provides essential information for the safe and efficient use of the XINJE XD5 Series XD5-24T-E Programmable Logic Controller (PLC). It covers installation, operation, maintenance, and troubleshooting procedures. Please read this manual thoroughly before operating the device.

XINJE XD5-24T-E PLC front view with ports
Figure 1: Front view of the XINJE XD5-24T-E PLC, showing input/output terminals and USB port.

2. Safety Information

Always observe the following safety precautions to prevent injury or damage to the device:

  • Ensure the power supply is disconnected before performing any wiring or maintenance.
  • Only qualified personnel should install, operate, and maintain this device.
  • Verify correct wiring connections to prevent short circuits or electrical hazards.
  • Do not expose the device to excessive moisture, dust, or extreme temperatures.
  • Use appropriate personal protective equipment (PPE) when working with electrical systems.

3. Setup

3.1 Unpacking and Inspection

Upon receiving the product, carefully unpack it and inspect for any signs of damage during transit. Ensure all components are present.

XINJE XD5-24T-E PLC in its retail box
Figure 2: The XINJE XD5-24T-E PLC packaged in its retail box.

3.2 Mounting

The XD5-24T-E PLC is designed for DIN rail mounting or screw mounting. Ensure a stable and vibration-free environment. Allow adequate space around the unit for ventilation and wiring access.

XINJE XD5-24T-E PLC rear view showing mounting clips
Figure 3: Rear view of the PLC, illustrating the integrated DIN rail mounting clips.

3.3 Wiring

Connect the power supply, digital inputs, and digital outputs according to your application's requirements. The device operates on AC220V. Ensure all connections are secure and correctly terminated.

  • Power Supply: Connect AC220V to the designated power terminals.
  • Digital Inputs (DI): The unit features 14 digital inputs. Connect sensors or switches to these terminals.
  • Digital Outputs (DO): The unit features 10 transistor outputs. Connect actuators or indicators to these terminals.
  • Communication Ports: USB, RS232, and RS485 ports are available for programming and communication with other devices.
XINJE XD5-24T-E PLC front view with terminal covers closed
Figure 4: Front view of the PLC with protective covers over the terminal blocks.

4. Operating Instructions

4.1 Power On

After completing all wiring, apply power to the PLC. Observe the status indicators on the front panel:

  • PWR (Power): Illuminates when power is supplied.
  • RUN: Illuminates when the PLC is in run mode and executing the program.
  • ERR (Error): Illuminates or flashes to indicate a system error. Refer to the troubleshooting section for details.

4.2 Programming

The XINJE XD5 Series PLC requires dedicated programming software (typically provided by XINJE) to develop and download control logic. Connect your computer to the PLC via the USB port for programming. Refer to the software's documentation for detailed programming instructions.

4.3 Input/Output Operation

Monitor the status of digital inputs and control digital outputs through your programmed logic. The transistor outputs are suitable for driving various loads within their specified current limits.

Video 1: A brief overview of the XINJE XD5 Series PLC, showcasing its physical appearance and various models.

5. Maintenance

Regular maintenance ensures the longevity and reliable operation of your PLC.

  • Cleaning: Periodically clean the exterior of the PLC with a soft, dry cloth. Do not use harsh chemicals or abrasive materials. Ensure ventilation openings are free from dust and debris.
  • Environmental Check: Verify that the operating environment remains within the specified temperature and humidity ranges.
  • Connection Check: Regularly inspect all wiring connections for tightness and signs of corrosion or damage.
  • Firmware Updates: Check the manufacturer's website for any available firmware updates that may improve performance or address known issues.

6. Troubleshooting

This section provides solutions to common issues you might encounter.

6.1 Status Indicator Meanings

  • PWR Off: No power supply or power supply failure. Check AC220V connection.
  • RUN Off: PLC is in STOP mode or no program is loaded. Check program status via software.
  • ERR On/Flashing: Indicates a system error, such as a memory error, I/O error, or program syntax error. Connect to programming software to view detailed error codes and messages.

6.2 Communication Issues

  • No connection via USB/RS232/RS485: Verify cable connections, driver installation on your PC, and communication settings (baud rate, parity, data bits, stop bits) in the programming software.
  • Programming software cannot detect PLC: Ensure the PLC is powered on and the correct communication port is selected in the software.

6.3 Input/Output Malfunctions

  • Input not responding: Check wiring to the sensor/switch, ensure the sensor is functioning, and verify the input status in the programming software.
  • Output not activating: Check wiring to the actuator, ensure the actuator is functional, verify the output status in the programming software, and check if the program logic is correctly enabling the output.

7. Specifications

General Specifications
FeatureDescription
ModelXD5-24T-E
BrandXINJE (PFDE)
Power SupplyAC220V
Digital Inputs (DI)14
Digital Outputs (DO)10 (Transistor Type)
Communication Ports1x USB, 1x RS232, 1x RS485
Is Smart DeviceYes
CertificationCE
Typical ApplicationGrinder (example)

7.1 XD5 Series Feature Overview

Table of XINJE XD5 series features including ports, expansion, and counter/pulse outputs
Figure 5: Feature comparison table for various XINJE XD5 series models. Note that specific I/O counts for XD5-24T-E are 14DI/10DO as per product title.

7.2 Dimensions

XD5-24T-E Dimensions
MeasurementValue
Overall Height108.0 mm
Body Height100.0 mm
Top Width70.8 mm
Bottom Width62.8 mm
Depth89.0 mm
Mounting Hole DiameterØ4.2 mm (x2)
Dimensional drawing for XINJE XD5-24T-E PLC
Figure 6: Detailed dimensions of the XD5-24T-E PLC.

8. Warranty and Support

For warranty information and technical support, please refer to the official XINJE documentation or contact your authorized dealer. Keep your purchase receipt as proof of purchase.

9. User Tips

  • Model Verification: Ensure you select the correct model (e.g., XD5-24T-E) as different variants may have distinct features or I/O configurations. Always double-check the model number against your requirements.
  • Programming Software: Programming software is typically required for PLC configuration and may need to be downloaded separately from the manufacturer's website. Ensure compatibility with your operating system.
  • Environmental Control: Maintaining a stable environment (temperature, humidity, dust) is crucial for the long-term reliability of industrial controllers.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.