1. Introduction
The VAKIND ZK-1002T is a versatile 2.0 dual-channel stereo Bluetooth digital power amplifier board designed for high-fidelity audio applications. It offers both wireless Bluetooth 5.0 and wired AUX audio input options, providing flexibility for various audio sources. This module features independent adjustment for treble and bass, along with a main volume control. Built with an original imported TPA3116D2 power amplifier chip, it includes AM interference suppression and robust protection mechanisms to ensure stable and reliable performance.


2. Package Contents
Upon opening the package, please verify that all components are present:
- ZK-1002T Amplifier Board
- Assembly Shell Components (requires self-assembly)
- Screwdriver (for assembly)
- Accessory Bag (contains small parts for assembly)

3. Setup Instructions
3.1 Assembly
- Carefully unpack all components from the accessory bag.
- Assemble the protective shell around the amplifier board using the provided screwdriver and fasteners. Ensure all connections and controls are accessible.
3.2 Power Supply Connection
The ZK-1002T requires a DC power supply. Use a power adapter with the following specifications:
- Voltage: DC 12V to 24V
- Current: 5A or above
Important: Ensure the adapter's power output is sufficient for the amplifier's actual working power. Higher voltage within the specified range will result in higher output power.
3.3 Speaker Connection
Connect your passive speakers to the amplifier board's output terminals. The amplifier is compatible with speakers having the following characteristics:
- Power Rating: 20W to 200W
- Impedance: 4 to 8 ohms
Note: The smaller the speaker impedance, the greater the output power. Ensure speaker impedance matches the amplifier's capabilities to prevent damage.
3.4 Audio Input Connection
The ZK-1002T supports two audio input modes:
- AUX Input: Connect your audio source (e.g., smartphone, MP3 player) to the AUX-IN port using a 3.5mm audio cable.
- Bluetooth Input: For wireless connection, refer to the 'Operating Instructions' section for Bluetooth pairing.

4. Operating Instructions
4.1 Power On/Off and Volume Control
The main volume knob also functions as the power switch. Rotate the knob clockwise to turn on the amplifier and increase the volume. Rotate counter-clockwise to decrease the volume and turn off the amplifier.
4.2 Tone Adjustment
The ZK-1002T features independent controls for audio tone:
- Treble Knob: Adjusts the high-frequency response of the audio.
- Bass Knob: Adjusts the low-frequency response of the audio.
4.3 Bluetooth Pairing
- Ensure the amplifier board is powered on.
- The amplifier will automatically enter Bluetooth pairing mode, indicated by an audible prompt or LED indicator (if present).
- On your audio device (e.g., smartphone, tablet), enable Bluetooth and search for available devices.
- Select 'ZK-1002T' from the list of devices to pair.
- Once paired, an audible confirmation will be heard, and you can begin playing audio wirelessly.
Note: The Bluetooth 5.0 connection offers a transmission distance of up to 10 meters without occlusion.
5. Maintenance
- Cleaning: Use a soft, dry cloth to clean the amplifier board. Avoid using liquid cleaners or solvents.
- Environment: Keep the device in a dry environment, away from moisture, dust, and extreme temperatures.
- Heat Dissipation: Ensure adequate airflow around the heat sink to prevent overheating, especially during prolonged high-power operation. Do not obstruct the heat sink.
- Connections: Periodically check all wiring connections for tightness and ensure they are free from corrosion.
6. Troubleshooting
- No Sound or Low Volume:
- Check if the power supply is connected correctly and providing sufficient voltage/current.
- Ensure the main volume knob is turned up.
- Verify that the audio input source is active and connected properly (AUX cable or Bluetooth paired).
- Check speaker connections for proper polarity and secure contact.
- Confirm that the audio input signal is strong enough.
- Distorted Sound:
- Reduce the input volume from your audio source.
- Check if the speaker impedance matches the amplifier's recommended range (4-8 ohms).
- Ensure the power supply is stable and sufficient.
- Adjust the Treble and Bass knobs to a neutral position or to your preference.
- Bluetooth Connection Issues:
- Ensure the amplifier is in pairing mode.
- Verify your audio device's Bluetooth is enabled and within the 10-meter range.
- Remove any physical obstructions between the amplifier and the audio device.
- Try unpairing and re-pairing the device.
- Amplifier Shuts Down Unexpectedly:
- The amplifier has built-in protection mechanisms (overvoltage, undervoltage, overheat, DC detection, short circuit protection). If it shuts down, disconnect power immediately.
- Check for short circuits in speaker wiring.
- Ensure the power supply voltage is within the 12V-24V range.
- Allow the amplifier to cool down if it feels hot.
- Reduce the load (e.g., lower volume, check speaker impedance).
7. Specifications
| Feature | Specification |
|---|---|
| Model | ZK-1002T |
| Brand | VAKIND |
| Bluetooth Version | 5.0 (10m range, no occlusion) |
| SNR (Signal-to-Noise Ratio) | >90dB |
| Input Mode | AUX + Bluetooth |
| Number of Channels | 2.0 (Left and Right Stereo) |
| Amplifier Chip | TPA3116D2 (with AM interference suppression) |
| Adaptive Power Supply | DC 12V ~ 24V / 5A or above |
| Adapter Horn (Speaker) | 20W ~ 200W, 4 ~ 8 ohms |
| Output Power (Example) | 100W*2 @ 24V, 4 ohms 50W*2 @ 24V, 8 ohms 60W*2 @ 19V, 4 ohms 35W*2 @ 19V, 8 ohms 35W*2 @ 12V, 4 ohms 20W*2 @ 12V, 8 ohms |
| Protection Mechanisms | Overvoltage, Undervoltage, Overheat, DC Detection, Short Circuit Protection |
| Dimensions (L x W x H) | 110mm x 70mm x 21mm (4.3in x 2.8in x 0.83in) |
| Weight | 161g (including packaging) |
| Origin | Mainland China |

8. User Tips
- Power Supply Quality: The performance of the amplifier is highly dependent on the quality and stability of the power supply. Using a high-quality, stable DC power adapter within the recommended voltage and current range will yield the best audio output.
- Speaker Matching: Always match your speakers' impedance and power handling to the amplifier's specifications to prevent damage and ensure optimal sound quality.
- Bluetooth Antenna: The ZK-1002T typically uses an integrated Bluetooth antenna. For best wireless performance, ensure the board is not enclosed in a metal casing that could interfere with the signal. If you are looking for models with external antenna options (e.g., IPex base), please verify the specific model variant before purchase, as the ZK-1002T model described here does not feature one.
- Audio Input Level: Ensure the audio input signal is sufficient but not excessively high to avoid distortion.
9. Warranty and Support
This product is manufactured by VAKIND. For any technical support, troubleshooting assistance beyond this manual, or inquiries regarding warranty, please contact the seller or manufacturer directly. Keep your purchase records for reference.