1. Introduction
This manual provides detailed instructions for the safe and effective use of your KW-triO Paper Cutter, Model 13932. This versatile tool is designed for precise cutting of various materials, offering both 45° inclined and 90° flat surface cutting capabilities. It is perfect for DIY framing projects, cutting cardstock, KT board, foam board, and corrugated paper board. Please read this manual thoroughly before operation to ensure proper usage and to maximize the lifespan of your product.
2. Safety Information
Always prioritize safety when using cutting tools. Failure to follow these safety guidelines may result in injury or damage to the product.
- Keep fingers clear of the blade at all times.
- Ensure the safety latch is engaged when the cutter is not in use or during blade changes.
- Use on a stable, flat surface.
- Keep out of reach of children.
- Do not attempt to cut materials thicker than specified (max 8mm).
- Handle blades with extreme care.
3. Product Components
Familiarize yourself with the main parts of your KW-triO Paper Cutter:
- Anti-slip panel: Provides grip and stability for the material being cut.
- Pointer: Indicates the current cutting depth setting.
- Knife holder: Secures the blade in place.
- 90° Cut scale line: Guide for straight cuts.
- 45° Cut scale line: Guide for angled cuts.
- Safety strip: Protects the blade when not in use.
- Base: Provides a stable platform for cutting.
4. Setup and Preparation
Before you begin cutting, ensure the device is properly set up.
- Unpack the Cutter: Carefully remove the paper cutter from its packaging.
- Unlock the Blade: The safety latch is typically in a locked position. Pull out the red safety latch to unlock the blade.
- Adjust Cutting Depth:
- Push the blade holder to align the pointer with the '0' point position on the scale.
- Each advance on the scale corresponds to +1mm material thickness.
- The maximum cutting depth for bevel cuts is 5mm.
Figure 3: Adjusting Cutting Depth. Note: Bevel cutting can cut thickness of 5mm.
5. Operating Instructions
Your KW-triO Paper Cutter supports two main cutting modes: 45° oblique (bevel) and 90° straight (plane) cuts.
5.1. 45° Oblique Cutting Mode
This mode is commonly used for picture frames, framed cant trimming, and window cutting.
- Ensure the panel is fully lowered and the blade flapper is pulled out to unlock.
- Mark the desired cutting position on your material using a ruler.
- Place the front of the cutting knife against the ruler. Press down firmly with one hand, then slide the blade down to cut.
- Repeat for all required edges.
5.2. 90° Straight Knife Mode
This mode is often used for cutting plastic materials, cardstock, and other flat materials.
- Fully lift the tool holder panel with the blade retracted. Press the lock mode button after lifting.
- Mark the cutting position. Align the points on both sides of the cutter body with your marked line.
- Place the front of the cutter against the ruler. Press firmly with your hand, then press down the blade and slide along the ruler to cut.
- Repeat for all required edges.
5.3. Suggested Cutting Materials
The KW-triO Paper Cutter is suitable for:
- KT board
- Snow board
- Thick paperboard
- Corrugated paperboard
- Photo frame mounting paper
- Chevy board
The straight cutting effect is achieved with a stainless steel blade, ensuring a sharp, flat, and level edge.
6. Maintenance
6.1. Blade Replacement
To maintain optimal cutting performance, replace the blade when it becomes dull. Replacement blades can typically be found where the product was purchased or from authorized retailers.
- Ensure the safety latch is engaged and the blade is fully retracted.
- Carefully remove the blade holder from the cutter.
- Gently slide out the old blade from the holder.
- Insert a new carbon steel blade into the holder, ensuring it is securely seated.
- Reinsert the blade holder into the cutter.
- Always dispose of old blades safely.
6.2. Cleaning
Wipe the cutter with a dry, soft cloth after each use to remove any paper dust or debris. Do not use abrasive cleaners or solvents.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Uneven or rough cuts | Dull blade, improper depth setting, material not held firmly. | Replace blade, adjust cutting depth, ensure material is stable during cut. |
| Blade not cutting through material | Material too thick, blade not extended enough, dull blade. | Check material thickness against specifications, adjust cutting depth, replace blade. |
| Cutter jams or sticks | Debris in blade path, material too thick or soft. | Clean the blade area, ensure material is suitable for cutting. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | 13932 |
| Product Name | 45° Bevel & 90° Plane Cutting Knife |
| Power | Manual |
| Blade Material | Carbon Steel |
| Cutting Thickness | ≤8mm |
| Product Weight | 0.72 kg (720g) |
| Product Size | 101 x 66 x 60 mm |
| Main Use | Photo frame mounting paper, KT board, Chevy board, corrugated board edge 45° bevel or 90° plane cutting |
9. User Tips
- For best results, always use a sharp blade. Keep spare blades on hand for quick replacement.
- When making long cuts, apply even pressure along the entire length of the cut to ensure a smooth finish.
- Use a cutting mat to protect your work surface and prolong blade life.
- Practice on scrap material before making important cuts.
10. Video Demonstration
Watch this video for a visual guide on operating your KW-triO Paper Cutter, including safety features, depth adjustment, cutting modes, and blade replacement.
11. Warranty and Support
For any questions, technical support, or warranty claims, please contact the retailer or manufacturer directly. Keep your purchase receipt as proof of purchase.
