Skydance LED Dimmer Controller User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Skydance LED Dimmer Controller. These controllers are designed for precise dimming of LED strips using RF 2.4G wireless technology, push dimming, and various remote control options. Please read this manual thoroughly before use to ensure proper functionality and safety.

Figure 1: Overview of Skydance LED Dimmer Controller models (V1, V1-L, V1-L/P, V1-H, V1-H/P, V1-T, V1-K, V1-N, V1-M, V1-W, T1, T1-1, T1-K, V1+R6-1, V1+R11).

2. Key Features

• PWM Constant Voltage Output: 1, 3, or 4 channels available.
• Smooth Dimming: 4096 levels of 0-100% flicker-less dimming, 256 level brightness, 4096 level gray-scale.
• Wireless Control: RF 2.4G technology with a remote control distance of up to 30 meters.
• Auto-Transmitting Function: Controllers automatically transmit signals to other controllers within 30m, extending control distance.
• Synchronization: Multiple controllers can be synchronized.
• Multiple Remote Support: Can accept 1 to 10 remote controls for partitioned control.
• Push Switch Compatibility: Connects with external push switches for on/off and 0-100% dimming.
• Selectable Fade Time: Light on/off fade time of 3 seconds is selectable.
• Protection Features: Over-heat, over-load, short circuit, and reverse polarity protection with automatic recovery.
• Various Dimming Methods: Supports push switch, touch button, knob, and digital tube display (model dependent).
• Expandable Output: Works with power repeaters for unlimited output expansion.

3. Model Overview and Specific Features

The Skydance V1 series offers various models, each with specific functionalities:

V1 LED Dimmer

• 4096 levels 0-100% dimming smoothly without any flash.
• Match with RF 2.4G single zone or multiple zone dimming remote control.
• One RF controller accepts up to 10 remote controls.
• Auto-transmitting function: Controller automatically transmits signal to another controller with 30m control distance.
• Synchronize on multiple number of controllers.
• Connect with external push switch to achieve on/off and 0-100% dimming function.
• Light on/off fade time 3s selectable.
• Over-heat / Over-load / Short circuit protection, recover automatically.

V1-L LED Dimmer

• Similar features to V1, designed for specific load requirements.
• 4096 levels 0-100% dimming smoothly without any flash.
• Match with RF 2.4G single zone or multiple zone dimming remote control.
• One RF controller accepts up to 10 remote controls.
• Auto-transmitting function: Controller automatically transmits signal to another controller with 30m control distance.
• Synchronize on multiple number of controllers.
• Connect with external push switch to achieve on/off and 0-100% dimming function.
• Light on/off fade time 3s selectable.
• Over-heat / Over-load / Short circuit protection, recover automatically.

V1-L/P LED Dimmer

• Includes logarithmic or linear dimming curve selectable.
• PWM frequency 500Hz, 2kHz, 8kHz or 16kHz selectable.
• All other features similar to V1-L.

V1-H LED Dimmer

• Designed for easy placement in standard wall junction boxes behind a push switch.
• All other features similar to V1.

V1-H/P LED Dimmer

• Combines features of V1-H with selectable logarithmic/linear dimming curves and PWM frequencies (250Hz, 500Hz, 2kHz or 8kHz).

V1-T LED Dimmer

• RF remote, 0/1-10V, Push Dim (3-in-1) dimming.
• Auto-transmitting function with 15m control distance.
• All other features similar to V1.

V1-K LED Dimmer

• Rotary dimmer with digital numeric display, visible dimming level.
• High load current up to 20A.
• Logarithmic or linear dimming curve selectable.
• PWM frequency 500Hz, 2kHz, 8kHz or 16kHz selectable.
• All other features similar to V1.

V1-N LED Mini RF Controller

• 1 channel constant voltage single color LED mini RF controller.
• 3A per channel, max output power 75W for 5-meter single color LED strip.
• Connects with push switch for on/off and dimming.
• Optional RF 2.4G single zone or multiple zone dimming remote control.
• Auto-transmitting function with 30m control distance.

V1-M LED Mini RF Controller

• 1 channel constant voltage single color LED mini RF controller.
• 5A output for 5-meter single color LED strip.
• Match with RF 2.4G single zone or multiple zone dimming remote control.
• Auto-transmitting function with 30m control distance.

V1-W LED Mini RF Controller

• 1 channel constant voltage single color LED mini RF controller.
• 3A per channel, max output power 75W for 5-meter single color LED strip.
• Match with RF 2.4G single zone or multiple zone dimming remote control.
• Auto-transmitting function with 30m control distance.

T1 Touch Panel

• Touch panel for single color, dual color, RGB or RGBW PWM constant voltage control.
• Ultra-sensitive high strength glass touch panel with touch color wheel.
• Compatibility with RF 2.4G single zone or multiple zone remote control.
• Touch keys with LED indicator.
• Available in White & Black glass panel.

T1-1 Touch Panel

• Touch panel for single color, dual color, RGB or RGBW PWM constant voltage control.
• Ultra-sensitive high strength glass touch panel with touch color slide.
• Compatibility with RF 2.4G single zone or multiple zone remote control.
• Touch keys with LED indicator.
• Available in White & Black glass panel.

T1-K Rotary Panel

• Rotary panel for single color, dual color or RGB PWM constant voltage control.
• Rotate knob to change RGB color, color temperature or brightness.
• 256 levels 0-100% dimming smoothly without any flash.
• Compatibility with RF 2.4G single zone or multiple zone remote control.
• PWM frequency 2KHz or 8KHz selectable.
• Push/Rotate with LED indicator.
• Available in White & Black glass panel.

V1+R6-1 Controller Set

• Remote control or connected with external push switch for on/off and dimming.
• Ultra-sensitive brightness adjustment touch wheel.
• Smooth dimming and switch without flickering.
• Auto-transmitting function: Controller automatically transmits signal to another controller with 30m control distance.
• Light on/off fade time 3s selectable.

V1+R11 Controller Set

• Remote control or connected with external push switch for on/off and dimming.
• Ultra-sensitive brightness adjustment touch slide.
• Smooth dimming and switch without flickering.
• Auto-transmitting function: Controller automatically transmits signal to another controller with 30m control distance.
• Synchronize on multiple number of controllers.
• Light on/off fade time 3s selectable.
• Magnet on the back for easy mounting on holder or metal surfaces.

4. Technical Specifications

Specifications may vary slightly by model. Refer to the specific model's documentation for precise details.

General Specifications (V1 Model Example)

Table 1: Technical Parameters for V1 LED Dimmer.

Other Model Dimensions

Figure 2: Mechanical Structures and Installation Dimensions for V1 LED Dimmer (97mm length, 33mm height, 18mm depth).

Figure 3: Mini design of V1-N (60x14mm, Max. 3A output) and V1-M (64x23.5x8.5mm, Max. 5A output) LED Dimmers.

5. Setup and Installation

5.1 Wire Preparation

• Wiring can be solid or stranded with a cross-sectional area of 0.5 to 2.5 mm².
• Conventional 1 mm² wire can withstand 10A output current.
• Ensure terminals are tightened securely during installation to prevent high contact resistance and overheating.

Note:

• The output power of a constant voltage power supply should be at least 1.2 times that of the output load (light strip) to prevent flickering or shaking.
• The product does not include batteries.

5.2 Wiring Diagrams

Figure 4: Wiring Diagram for V1 LED Dimmer. Shows connections for power supply, LED strip, and optional push switch or RF remote.

Figure 5: Wiring Diagram for V1-W LED Dimmer. Connects to a 12-24VDC power supply and a 5m single color LED strip, controlled by a dimming remote.

Figure 6: Wiring Diagram for V1-M LED Dimmer. Connects to a 12-24VDC power supply and a 5m single color LED strip, controlled by a dimming remote.

Figure 7: Wiring Diagram for V1-L/P LED Dimmer. Shows connections for power supply, LED strip, and optional push switch or RF remote.

Figure 8: Wiring Diagram for V1-L LED Dimmer. Shows connections for power supply, LED strip, and optional push switch or RF remote.

Figure 9: Wiring Diagram for V1-H LED Dimmer. Shows connections for power supply, LED strip, and optional push switch or RF remote.

Figure 10: Wiring Diagram for V1+R6-1 Controller Set. Shows connections for power supply, LED strip, and optional push switch or RF remote.

Figure 11: Wiring Diagram for V1-K LED Dimmer. Shows connections for power supply and single color LED strip.

5.3 Installation Precautions

• Products should not be stacked. Maintain a distance of ≥ 20cm to avoid affecting lifespan due to poor heat dissipation.
• Do not install the product close to a switching power supply (maintain ≥ 20cm interval) to avoid radiation interference.
• Installation height should be ≥ 1m from the floor to avoid shortening remote control distance due to weak reception.
• Keep products away from or uncovered by metal objects (maintain ≥ 20cm interval) to avoid signal attenuation.
• Avoid installation at wall corners or beam corners (maintain ≥ 20cm interval) to avoid signal interference.

6. Operating Instructions

6.1 Match Remote Control (Two Ways)

End users can choose between two methods to match or delete remotes:

Method 1: Using the Controller's Match Key

• Match: Short press the match key on the controller, then immediately press the on/off key (for single zone remote) or a zone key (for multiple zone remote) on the remote. The LED indicator will flash a few times, indicating successful matching.
• Delete: Press and hold the match key for 5 seconds to delete all matched remotes. The LED indicator will fast flash a few times, confirming all remotes are deleted.

Method 2: Using Power Restart

• Match: Switch off the power to the receiver, then switch it on again. Immediately short press the on/off key (for single zone remote) or a zone key (for multiple zone remote) 3 times on the remote. The light will blink 3 times, indicating successful matching.
• Delete: Switch off the power to the receiver, then switch it on again. Immediately short press the on/off key (for single zone remote) or a zone key (for multiple zone remote) 5 times on the remote. The light will blink 5 times, confirming all remotes are deleted.

Figure 12: Illustration of Match Remote Control methods for V1 LED Dimmer.

Figure 13: Illustration of Match Remote Control methods for V1-M LED Dimmer.

6.2 Push Dim Function

The Push-Dim interface allows for simple dimming using commercially available non-latching (momentary) wall switches.

• Short press: Turns the light on or off.
• Long press (1-6s): Press and hold for step-less dimming. Each subsequent long press reverses the dimming direction.

Figure 14: Push Switch Control Option for V1-H LED Dimmer. Short press for ON/OFF, press and hold to dim brightness.

6.3 Light On/Off Fade Time

• To set fade time to 3 seconds: Long press the match key for 5 seconds, then short press the match key 3 times. The indicator light will blink 3 times.
• To restore factory default (0.5s fade time): Long press the match key for 10 seconds.

6.4 Dimming Memory

The light returns to the previous dimming level when switched off and on again, even after a power failure.

6.5 Synchronization

If multiple controllers are connected to the same push switch, perform a long press for more than 10 seconds. The system will synchronize, and all lights in the group will dim up to 100%. This eliminates the need for additional synchrony wiring in larger installations.

It is recommended that the number of controllers connected to a single push switch does not exceed 25 pieces. The maximum length of wires from the push switch to the controller should not exceed 20 meters.

Figure 15: Application Notes for V1 LED Dimmer, illustrating auto-transmitting and auto-synchronization.

6.6 Remote Control Ways

RF 2.4GHz wireless technology allows matching with various Skydance handheld remotes, wall touch panel remotes, and iOS/Android smartphones via a WiFi-Relay converter.

Figure 16: Three Remote Control Ways: Smart phone with WiFi-Relay, Handheld remote, and Wall touch panel.

Figure 17: V1-N LED Push Dimmer.

Figure 18: T1 Touch Panel.

Figure 19: V1 and R6-1 Controller Set.

Figure 20: V1 and R11 Controller Set.

6.7 Panel Key Functions (T1-1 Example)

Figure 21: Key Functions for T1-1 Touch Panel. Includes controls for single color, dual color, RGB, and RGBW modes.

7. Maintenance

To ensure the longevity and optimal performance of your Skydance LED Dimmer Controller, follow these maintenance guidelines:

• Keep the device clean and free from dust. Use a soft, dry cloth for cleaning.
• Avoid exposing the controller to extreme temperatures or humidity.
• Ensure proper ventilation around the device to prevent overheating.
• Do not use harsh chemicals or abrasive cleaners on the device.
• Regularly check wiring connections for tightness and signs of wear.

8. Troubleshooting

If you encounter issues with your LED Dimmer Controller, refer to the table below for common problems and solutions.

Table 2: Malfunctions Analysis & Troubleshooting.

9. Warranty and Support

9.1 Warranty

The product comes with a 5-year warranty. Protection includes:

• Reverse polarity protection
• Over-heat protection
• Over-load protection
• Short circuit protection

9.2 Certifications

The product is certified with CCC, CE, and RoHS standards, ensuring compliance with safety and environmental regulations.

• EMC standard: EN IEC 55015 / EN IEC 61547, ETSI EN 301 489-1/-3
• Safety standard: EN 61347-1/-2
• Radio Equipment: ETSI EN 300 440
• Certification: CE RED FCC

9.3 FCC ID Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

10. User Tips

• For optimal wireless performance, ensure the controller is not obstructed by metal objects and is installed at a height of at least 1 meter.
• When using multiple controllers with a single push switch, utilize the synchronization feature to ensure consistent dimming across all lights.
• Always verify the power supply's output capacity matches or exceeds the total load of your LED strips to prevent flickering or damage.