DIAIARY BPS3010

Contents

DIAIARY Adjustable DC Laboratory Power Supply User Manual

Models: BPS3010, BPS305, BPS605, BPS1203, BPS325, BPS3210, BPS3201

1. Safety Information

Before using this power supply, please read this manual thoroughly, especially the safety instructions, to prevent personal injury or damage to the power supply and connected electronic devices.

1.1 Initial Inspection

  • Check for any damage caused during transportation.
  • Verify that all accessories are complete.
  • Before powering on, confirm the product matches your actual input voltage.
  • After powering on, check if the output voltage and current are normal.

If any issues are found during these checks, please contact your dealer.

1.2 Safety Symbols

The following safety symbols may appear in this manual or on the device:

Ground symbolGround Symbol: Indicates connection to earth ground.
High voltage warning symbolHigh Voltage Warning: Indicates dangerous voltage levels.
General warning symbolWarning Symbol: Indicates caution or warning.

1.3 Usage Requirements

  • Use a power cord that meets the product's power requirements.
  • The power supply must be reliably grounded. The internal anti-electromagnetic interference circuit may cause slight leakage current, which should be directed to ground. Failure to ground properly may damage load equipment or reduce anti-interference capability.
  • When charging rechargeable batteries (e.g., lead-acid batteries), ensure correct polarity (+ to + and - to -). Incorrect connection can damage the internal rectifier or the load equipment.
  • Do not use the product in environments with flammable, explosive, humid, or corrosive gases.
  • The product generates heat during operation, especially at full power. Use it in a well-ventilated area and ensure no obstructions around the cooling fan and vents.
  • Use output wires of sufficient gauge for the output current. Ensure connections to the power supply and load are firm, clean, and free of rust to prevent overheating and potential fire.
  • The internal components of the machine contain high voltage, even when powered off. Do not attempt to repair or modify the device yourself to avoid expanding faults or personal injury.
  • Confirm the allowed AC input voltage (AC 230V±10% or AC 115V±10%) using the switch on the rear panel.

WARNING: Incorrect AC input voltage selection will cause severe damage to the machine. Always verify the required input voltage.

2. Product Features

The DIAIARY BPS series is a digital display adjustable switching DC regulated power supply. It simultaneously displays voltage, current, and power. The output voltage and current are continuously adjustable between 0 and the nominal value using encoder knobs.

  • Constant voltage and constant current automatic switching function.
  • Independent Output ON/OFF button for easy control.
  • Short circuit protection (OCP) alarm function.
  • Four-digit display for voltage, current, and power.
  • Low noise, temperature-controlled cooling fan.
  • Over-temperature protection (OTP) automatically disables output if internal temperature exceeds 75°C.
  • Memory function: Voltage and current settings are automatically saved upon power off.
  • USB and Type-C quick charge ports (up to 18W).
  • Dual voltage input (AC 115V/230V) with convenient selection switch.
Product features: Constant current, Constant voltage, Temperature control, Two years warranty, Heat-resistant, Low ripple, Safety and health.

Key features of the DIAIARY DC Power Supply.

Attention to detail: Alloy metal body, High-definition digital display screen, Temperature controlled fan, QC3.0 fast charging.

Detailed view of the power supply's construction and features.

New upgrades and multiple protections: SCP (Short-circuit protection), OVP (Over-voltage protection), OCP (Overcurrent protection), OPP (Overload protection), OTP (Over-temperature protection).

Multiple protection mechanisms for safe operation.

Internal view showing high quality precision components and certifications like CE, FCC, RoHS.

Internal components and compliance certifications.

Craftsmanship and Quality Assurance: High precision, Accurate Power, Fast Charging, Preset Current, Constant Voltage and Current, Intelligent Temperature Control, Over Voltage Protection, Small Size, CNC adjustment, Sturdy Durable.

Overview of the power supply's quality and design principles.

3. Product Overview

3.1 Front Panel Description

Front panel diagram with labels for Voltage, Current, Power, CV, CC, OCP, Output, Mute, OCP button, Voltage knob, Current knob, USB-C, USB-A, Power button, Quick Charge, GND, Positive, Negative terminals.

Front panel layout and controls.

  1. Power Switch: Turns the power supply ON or OFF.
  2. Voltage Display: Shows the set or actual output voltage.
  3. Current Display: Shows the set or actual output current.
  4. Output Power Display: Shows the calculated output power.
  5. CV (Constant Voltage) Indicator: Lights up when the unit is operating in constant voltage mode.
  6. CC (Constant Current) Indicator: Lights up when the unit is operating in constant current mode.
  7. OCP (Overcurrent Protection) Indicator: Lights up when OCP is enabled.
  8. OUT (Output) Indicator: Lights up when output is enabled.
  9. Output Switch: Toggles the power output ON or OFF. Pressing it also clears OCP alarms.
  10. Mute Button: Toggles the buzzer sound ON or OFF.
  11. OCP Button: Enables or disables the overcurrent protection function.
  12. Voltage Adjustment Knob: Rotates to adjust voltage. Press to shift digit for fine adjustment. Settings are saved after 3 seconds of inactivity.
  13. Current Adjustment Knob: Rotates to adjust current. Press to shift digit for fine adjustment. Settings are saved after 3 seconds of inactivity.
  14. USB-A Quick Charge Port: Provides up to 18W quick charging, compatible with various fast charge protocols. Outputs standard 5V for non-quick charge devices.
  15. USB-C Quick Charge Port: Similar to USB-A, provides up to 18W quick charging via Type-C.
  16. Positive Output Terminal (+): Connects to the positive terminal of the load.
  17. Negative Output Terminal (-): Connects to the negative terminal of the load.
  18. Ground Terminal (GND): For grounding the device.

3.2 Rear Panel Description

Rear panel diagram with labels for Cooling fans, Heat dissipation holes, Input voltage selector switch, Power input socket, Fuse box.

Rear panel layout and components.

  1. Fuse Box: Contains the fuse for protection.
  2. AC Power Input Socket: Connects the power cord.
  3. AC Input Voltage Selector Switch: Allows switching between AC 115V and AC 230V input.
  4. Cooling Fan: Temperature-controlled fan for heat dissipation, activates automatically when temperature reaches 45°C.

4. Setup and Operation

4.1 Connecting Power

Video demonstrating the power supply's features and connections.

Operating method step 1: Connect the power cord. Step 2: When unit is powered on, press the power switch button. Step 3: Rotate current/voltage knobs to adjust, press for precision. Step 4: After adjusting, press output key to start outputting. Also shows 115V-230V voltage range and product fuses.

Step-by-step guide for connecting power and initial operation.

  1. Ensure the AC input voltage selector switch on the rear panel is set correctly (115V or 230V) for your region.
  2. Connect the provided power cord to the AC power input socket on the rear panel and then to a grounded wall outlet.

4.2 Power On/Off

  1. Press the POWER button on the front panel to turn the power supply ON. The screen will display the last set voltage and current values.
  2. Press the POWER button again to turn the power supply OFF.

4.3 Adjusting Voltage and Current

  1. Rotate the VOLTAGE knob to adjust the desired voltage. The currently selected digit will flash. Press the knob to move to the next digit for fine adjustment.
  2. Rotate the CURRENT knob to adjust the desired current limit. The currently selected digit will flash. Press the knob to move to the next digit for fine adjustment.
  3. Settings are automatically saved after approximately 3 seconds of inactivity.

4.4 Connecting Load

Diagram showing Output button to turn on/off output and OCP for short circuit protection and alarm.

Output control and OCP function.

  1. Loosen the binding post knobs by rotating them counter-clockwise.
  2. Insert the banana plugs of your output wires into the positive (+) and negative (-) terminals. If using bare wire, insert the wire into the hole and tighten the knob.
  3. Ensure the connections are firm and secure.
  4. Connect the other end of the output wires to your load device, ensuring correct polarity.

WARNING: Incorrect connection, especially when charging batteries, can damage the power supply or the load. Always double-check polarity.

4.5 Enabling/Disabling Output

  1. Press the Output button on the front panel to enable or disable the power output. The OUT indicator will light up when output is enabled.

4.6 OCP (Overcurrent Protection)

  1. Press the OCP button to enable or disable the overcurrent protection function. When enabled, the OCP indicator will light up.
  2. If a short circuit or overcurrent condition occurs, the power supply will stop outputting and trigger an alarm. Press the Output button to clear the alarm and return to the OFF state.

4.7 Constant Voltage (CV) and Constant Current (CC) Characteristics

This power supply features automatic CV/CC crossover. It operates in constant voltage mode until the load current reaches the set current limit, then it switches to constant current mode. The CV and CC indicators on the front panel show the current operating mode.

  • Constant Voltage (CV) Mode: The output voltage remains constant at the set value, and the output current varies according to the load.
  • Constant Current (CC) Mode: The output current remains constant at the set value, and the output voltage varies according to the load.

NOTE: In OCP mode, the power supply cannot operate in constant current mode as it will shut down output upon detecting an overcurrent condition.

5. Maintenance

5.1 Fuse Replacement

Diagram showing how to remove the fuse holder from the power input socket and replace the fuse.

Steps for fuse replacement.

If the fuse blows, the unit will stop working. Identify and correct the cause of the blown fuse before replacing it with a fuse of the same specifications.

  1. Disconnect the power cord from the power supply and the wall outlet.
  2. Locate the fuse box within the AC power input socket on the rear panel.
  3. Use a flat-head screwdriver to gently pry open the fuse holder.
  4. Remove the old fuse and insert a new fuse of the correct rating.
  5. Push the fuse holder back into the socket until it clicks into place.

WARNING: High voltage. For safety, only replace with a fuse of the specified type and rating. Always disconnect power before replacing the fuse.

5.2 Cleaning

  • Disconnect the power supply when not in use or before cleaning.
  • Unplug the power cord before cleaning the machine.
  • Do not use hydrocarbons, chlorinated solvents, or similar solvents. Do not use abrasive cleaners.

6. Troubleshooting

6.1 Power Supply Does Not Turn On

  • Check if the power cord is properly connected and if there is AC power from the outlet.
  • Verify that the fuse is intact. Replace if blown (refer to Section 5.1).

6.2 No Output

  • Check if the Output button is pressed and the OUT indicator is lit.
  • Verify that the output wires are correctly connected and not damaged.
  • Ensure that the voltage and current settings are not set to zero.

6.3 Voltage Cannot Reach Maximum Value

  • Check the AC input voltage selector switch on the rear panel. If you are using a 110V supply, ensure the switch is set to 115V.

6.4 Display Screen Appears Scratched

  • The LED digital display has a protective film to prevent scratches during transport. If the display appears unclear, you can remove this protective film.

6.5 Cooling Fan Does Not Work

  • The cooling fan is located on the rear of the power supply. It is temperature-controlled and will only activate automatically when the internal temperature reaches a certain threshold (e.g., 45°C), not continuously.

6.6 Output Current Does Not Match Set Value

The set current value is the maximum limit the power supply will output. The actual output current is determined by the load's requirements, but it will not exceed the set current limit.

7. Specifications

Table of specifications including Output Power, Output Voltage, Output Current, Working Environment (Input Voltage, Working Temperature, Relative Humidity, Storage Temperature), Constant Voltage (CV) characteristics (Voltage stability, Load stability, Ripple voltage, Adjustable range), and Constant Current (CC) characteristics (Current stability, Load stability, Ripple current, Recovery time, Temperature coefficient, Adjustable range).

Detailed technical specifications.

General Specifications
ParameterValue
Output Power150W/300W/320W/360W (model dependent)
Output Voltage0~30V/60V/120V/160V (model dependent)
Output Current0~2A/3A/5A/10A (model dependent)
Input VoltageAC 230V/115V ±10%; 50Hz/60Hz
Working Temperature0℃~40℃; Relative Humidity: <80%RH
Storage Temperature-10℃~70℃; Relative Humidity: <70%RH
Voltage Stability (CV)0.1% ±3mV
Load Stability (CV)0.2% ±3mV
Ripple Voltage (CV)≤0.5% Vp-p
Current Stability (CC)0.1% ±3mA
Load Stability (CC)0.2% ±3mA
Ripple Current (CC)≤0.5% Vp-p
Display Accuracy0.5% + 5 digits
Display ResolutionVoltage: 0.01V; Current: 0.001A (0.1V for >100V, 0.01A for >10A)

7.1 Dimensions and Weight

Product dimensions: 190mm length, 90mm width, 145mm height. Net weight 1.15kg. Max power = Voltage x Current. Input voltage range 115V-230V ±10%. Shows cooling fuselage.

Physical dimensions and weight of the power supply.

Product size long 190mm x wide 90mm x tall 145mm.

Detailed dimensions of the power supply unit.

  • Product Size: 190mm (Length) x 90mm (Width) x 145mm (Height)
  • Net Weight: 1.15kg
  • Gross Weight (with packaging): 1.5kg
  • Package Size: 265mm (Length) x 135mm (Width) x 195mm (Height)

8. What's in the Box

Packaging accessories: 1x Output line, 1x Power cable, 1x Product Manuals, 1x Product Body.

Contents of the product packaging.

Package contains: User manual x1, Test line x1, Power cord x1, DC Power supply x1.

Detailed list of items included in the package.

  • 1x DC Power Supply Unit
  • 1x Power Cord (EU, US, UK, AU plug type will be configured according to your country)
  • 1x Test Line (Output Load Cables)
  • 1x User Manual

9. Applications

Wide range of applications: Electronic repair, Engineering testing, Product ageing, Battery power, Laboratory, DC motor testing.

Common uses for the DIAIARY DC Power Supply.

This power supply is suitable for a wide range of applications, including:

  • Production line testing
  • Mobile phone, computer, and electrical appliance maintenance
  • Product aging tests (e.g., resistors, capacitors, relays, DC motors, LEDs)
  • Battery charging
  • Laboratory, scientific research, and teaching environments
  • Any other occasion requiring a stable DC power supply

10. User Tips

  • Output Cables: The included output cables may be of basic quality. For regular or critical use, consider purchasing higher quality banana plugs or screw terminal cables for better performance and durability.
  • Display Brightness: The screen is very bright. You can adjust the display brightness through the system settings. Long press the current adjustment knob for 5 seconds to enter settings, then rotate the current knob to adjust brightness (levels 1-5). Press the voltage knob to exit and save.
  • Output Exceeds Nominal: Some units may provide slightly higher output than their nominal ratings (e.g., a 30V supply might go up to 32V, and a 5A supply might reach 5.5A).

11. Warranty and Support

11.1 Product Warranty

This product comes with a one-year free repair service from the date of purchase. The warranty does not cover:

  • Failure to present the product warranty card.
  • Malfunctions caused by abnormal use, improper operation, unauthorized repairs, modifications, or adjustments.
  • Consumable materials.
  • Damage due to natural disasters such as floods, fires, or earthquakes.

Repair services beyond the warranty period will incur repair fees, and the user will be responsible for any associated costs.

11.2 Support

If you encounter any problems with the product or have quality concerns, please contact our after-sales service personnel. If necessary, the power supply may need to be sent to the company for repair. Due to high voltage inside the machine (even when powered off), do not attempt to repair or modify it yourself.

For further detailed information, you can refer to the official user manual PDF: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.