Introduction
This manual provides comprehensive instructions for the setup, operation, maintenance, and troubleshooting of your new Scimagic-RC Ditec GOL4 compatible garage door remote control. This remote is designed to work with DITEC rolling code systems operating at 433.92MHz.
Compatibility
This remote control is 100% compatible with the following DITEC rolling code models:
- DITEC GOL4
- DITEC BIXLG4
- DITEC BIXLP2
- DITEC BIXLS2
- DITEC Entrematic ZEN 2
- DITEC Entrematic ZEN 4
- DITEC Entrematic ZEN2W
- DITEC Entrematic ZEN4W
IMPORTANT NOTE: This remote is NOT compatible with DITEC GOL4C (fixed code) models. Please ensure your original remote is a rolling code type.
Specifications
| Feature | Specification |
|---|---|
| Name | Ditec Compatible Remote |
| Frequency | 433.92 MHz |
| Battery | 3V (CR2032 included) |
| Operating Distance | 20-100m (open area) |
| Encoding Method | Rolling Code |
| Number of Buttons | 4 |
| Dimensions | 60mm x 37mm x 5mm |
Setup
Battery Installation
The remote control comes with a CR2032 battery pre-installed. If you need to replace it:
- Locate the battery compartment cover on the back of the remote.
- Carefully open the cover.
- Remove the old CR2032 battery.
- Insert a new 3V CR2032 battery, ensuring the positive (+) side is facing up.
- Close the battery compartment cover securely.
Programming the Remote Control
To program your new remote control to your DITEC gate or garage door opener, follow these steps. This process is similar to programming original DITEC transmitter remotes. Refer to your receiver's user manual for specific details if needed.
- Access the Receiver: Open the control box of your gate or garage door opener and locate the receiver board. Ensure that jumper JR6 on the receiver board is in the 'on' position.
- Initiate Programming: Press and hold the black 'PRG' (Program) button on the receiver board for approximately 5 seconds.
- Program New Remote: While the receiver is in programming mode, press and hold the button on your new remote control that you wish to activate the device. Hold this button for approximately 5 seconds.
- Test and Reset: Wait for 10 seconds for the receiver to reset. After this, test the new remote control to ensure it operates correctly.
Operating Instructions
Once programmed, your remote control can be used to operate compatible DITEC systems. Simply press the programmed button on the remote to activate the garage door, gate, alarm, automatic door, or roller shutter.
Maintenance
The remote control requires minimal maintenance. The primary maintenance task is battery replacement when the remote's range decreases or it stops responding. Refer to the 'Battery Installation' section for instructions on replacing the CR2032 battery.
Troubleshooting
Remote Not Responding
- Check Battery: Ensure the battery is correctly installed and has sufficient charge. Replace if necessary.
- Re-program: Attempt to re-program the remote control following the steps in the 'Setup' section.
- Check Jumper JR6: Verify that jumper JR6 on the receiver board is in the 'on' position.
- Range: Ensure you are within the effective operating range (20-100m in open area). Obstacles can reduce this range.
Incompatibility Issues
If your remote is not working, double-check that your original DITEC remote uses a rolling code and is one of the compatible models listed. This remote is not compatible with DITEC GOL4C (fixed code) models. The GOL4 (rolling code) typically has a different LED indicator color than the GOL4C (fixed code).
Clearing All Stored Remotes (Reset Codes)
To clear all previously programmed remote controls from your DITEC receiver, effectively resetting it:
- Access the receiver board in your control box.
- Press and hold the 'PRG' (Program) button on the receiver board for a longer duration, typically 10-15 seconds, until the indicator light on the receiver changes or turns off.
- Release the button. All previously programmed remotes should now be cleared. You will need to re-program any remotes you wish to use.
Warranty and Support
Your purchase includes the following services:
- Return Service: Enjoy 7 days to return if any quality problems are encountered.
- Processing Time: Most items are shipped out within 24 working hours (excluding holidays).
- Shopping Help: All emails for support will be answered within 24 hours.
- Free Returns: Free returns are available within 90 days of purchase.
- Fast Delivery Guarantee: Includes a $1.00 coupon code if delivery is delayed, a refund if the package is lost, a refund if items are damaged, and a refund if no delivery occurs within 30 days.
- Security & Privacy: Your personal details are protected and not shared with third parties without your consent.
For further assistance, please contact customer support through the platform where you made your purchase.
