KKMOON ZL126/ZL128 Series Digital Multimeter

Contents

KKMOON ZL126/ZL128 Series Digital Multimeter User Manual

Model: ZL126A, ZL126B, ZL128A, ZL128B

1. Introduction

This manual provides comprehensive instructions for the safe and effective use of your KKMOON ZL126/ZL128 Series Digital Multimeter. Designed for electrical testing, automotive repair, and general household improvements, this device offers a range of measurement functions including voltage, current, resistance, capacitance, frequency, and temperature. Please read this manual thoroughly before operation to ensure proper use and to prevent potential hazards.

2. Safety Information

WARNING: Failure to follow these safety instructions may result in electric shock, fire, or personal injury.

  • Always ensure the multimeter is in the correct measurement mode before connecting test leads to a circuit.
  • Do not exceed the maximum input values specified for each function. Refer to the specifications section for details.
  • Exercise extreme caution when working with live circuits. Always assume circuits are live until proven otherwise.
  • Inspect test leads for damage (cuts, cracks, exposed metal) before each use. Replace immediately if damaged.
  • Do not operate the multimeter if it appears damaged or is not functioning properly.
  • Replace batteries promptly when the low battery indicator appears to ensure accurate readings and proper operation.
  • NCV (Non-Contact Voltage) detection is a safety feature and should not be used as the sole method to determine the presence of voltage. Always verify with direct contact measurements when possible.
  • Keep the device away from water, dust, and extreme temperatures.

3. Package Contents

Please check the package for the following items:

  • 1 x Digital Multimeter (ZL126A, ZL126B, ZL128A, or ZL128B model)
  • 2 x Universal Test Leads (Red and Black)
  • 1 x Temperature Probe (Included with ZL128A/ZL128B models only)
  • 1 x USB Charging Cable (Included with ZL126B/ZL128B models only)
  • 1 x User Manual
ZL128B Multimeter with test leads and USB cable
Figure 3.1: ZL128B Multimeter with included test leads and USB charging cable.

4. Product Overview

The ZL126/ZL128 series multimeters feature a concise design with a large, clear display and intuitive controls.

4.1 Key Features

  • Display: Large color display with backlight and large font for easy data reading.
  • Buttons: LIVE, HOLD, H/L NCV, SEL for mode selection and special functions.
  • Input Ports: Dedicated jacks for COM (common), VΩHz (voltage, resistance, frequency, capacitance, diode, continuity), and 10A (current measurement for ZL128A/B).
  • LED Flashlight: Built-in LED for illuminating dark work areas.
  • NCV Sensor: Non-contact voltage detection for enhanced safety.
  • Fire Wire Recognition: Identifies live wires.
  • Auto Power Off: Automatically shuts down after a period of inactivity to conserve battery.
ZL128B Multimeter with HD color large screen
Figure 4.1: HD color large screen display (9999 counts shown on ZL128B model).
Display symbol descriptions for the multimeter
Figure 4.2: Explanation of symbols on the multimeter display.

5. Setup

5.1 Battery Installation (ZL126A/ZL128A)

  1. Locate the battery compartment on the back of the multimeter.
  2. Open the compartment cover.
  3. Insert 3 AAA batteries, observing correct polarity (+ and -).
  4. Close the battery compartment cover securely.

5.2 Charging (ZL126B/ZL128B)

The ZL126B and ZL128B models feature a built-in 1000mAh rechargeable battery.

  1. Connect the provided USB Type-C cable to the multimeter's charging port.
  2. Connect the other end of the USB cable to a suitable USB power source (e.g., computer, USB wall adapter).
  3. The battery indicator on the display will show the charging status. A full charge provides long operating time.
USB Type-C charging port and 1000mAh battery for ZL126B/ZL128B models
Figure 5.1: USB Type-C charging port and internal 1000mAh battery for ZL126B/ZL128B models.

5.3 Connecting Test Leads

  1. Insert the black test lead into the "COM" (common) jack.
  2. For most measurements (voltage, resistance, capacitance, frequency, diode, continuity), insert the red test lead into the "VΩHz" jack.
  3. For current measurements (ZL128A/ZL128B models only), insert the red test lead into the "10A" jack.

6. Operating Modes and Functions

6.1 Power On/Off

Press the power button (typically a red button on the side or top) to turn the multimeter on or off. The device features automatic power-off to save battery life after a period of inactivity.

6.2 Automatic Mode

The multimeter defaults to auto-ranging mode, automatically detecting the measurement type (voltage, resistance, continuity) when test leads are connected to a circuit.

6.3 Manual Mode / Function Selection (SEL button)

Press the "SEL" button to cycle through different measurement functions within a mode (e.g., AC/DC voltage, diode/continuity).

6.4 Voltage Measurement (AC/DC)

  1. Connect test leads as described in Section 5.3.
  2. Select AC or DC voltage mode if not automatically detected.
  3. Apply probes to the circuit or component. The display will show the voltage and frequency (for AC voltage).
ZL128B Multimeter measuring AC voltage in a circuit breaker panel
Figure 6.1: Measuring AC voltage with the ZL128B multimeter.

6.5 Current Measurement (AC/DC, ZL128A/ZL128B only)

WARNING: Ensure the red test lead is in the "10A" jack. Never measure current in parallel with a voltage source; always break the circuit and insert the multimeter in series.

  1. Break the circuit and insert the multimeter in series with the load.
  2. Select AC or DC current mode.
  3. The display will show the current in Amperes (A).
ZL128B Multimeter measuring AC/DC current (0-10A)
Figure 6.2: Measuring AC/DC current (0-10A) with the ZL128B multimeter.

6.6 Resistance Measurement

  1. Ensure the circuit is de-energized before testing resistance.
  2. Connect test leads to the component.
  3. The display will show resistance in Ohms (Ω).

6.7 Capacitance Measurement

  1. Ensure the capacitor is fully discharged before testing.
  2. Connect test leads to the capacitor terminals.
  3. The display will show capacitance in Farads (F).

6.8 Diode Test

  1. Ensure the circuit is de-energized.
  2. Connect test leads to the diode.
  3. The display will show the forward voltage drop.

6.9 Continuity Test (On and Off Beep)

  1. Ensure the circuit is de-energized.
  2. Connect test leads across the component or wire.
  3. A continuous beep indicates continuity (low resistance).
Examples of capacitance, resistance, continuity (on/off beep), and DC voltage measurements
Figure 6.3: Demonstrations of capacitance, resistance, continuity, and DC voltage measurements.

6.10 Frequency Measurement

  1. Connect test leads to the signal source.
  2. The display will show frequency in Hertz (Hz).

6.11 Temperature Measurement (ZL128A/ZL128B only)

  1. Connect the temperature probe to the multimeter.
  2. Select temperature mode.
  3. Place the probe tip on or near the object to be measured.
  4. The display will show the temperature in Celsius (°C) or Fahrenheit (°F).
ZL128A Multimeter measuring temperature with a probe
Figure 6.4: Measuring temperature with the ZL128A multimeter and temperature probe.

6.12 NCV (Non-Contact Voltage) Detection

  1. Hold the NCV sensor (located at the top of the multimeter) near a live wire or electrical outlet.
  2. The multimeter will indicate the presence of AC voltage with an audible alarm and visual indicators on the display.
  3. Use the "H/L NCV" button to toggle between high and low sensitivity modes.
Multimeter performing NCV (Non-contact AC voltage detection)
Figure 6.5: Non-contact AC voltage detection (NCV) in action.

6.13 Live Wire Function (LIVE button)

  1. Connect the red test lead to the appropriate jack.
  2. Press the "LIVE" button to activate the live wire detection mode.
  3. Touch the red probe to the wire. The multimeter will indicate if it's a live wire.
ZL128B Multimeter demonstrating Fire Wire Recognition
Figure 6.6: Fire Wire Recognition using the ZL128B multimeter.

6.14 Data Hold (HOLD button)

Press the "HOLD" button to freeze the current reading on the display. Press it again to release the hold function and resume live readings.

6.15 Flashlight

Activate the built-in LED flashlight for illumination in dark environments by pressing the dedicated flashlight button (if available) or a combination of buttons as indicated on the device.

Multimeter showing bright LED flashlight
Figure 6.7: Bright LED lighting feature of the multimeter.

6.16 Line Break Point Detection

Utilize the NCV function to trace wires and detect breaks. The signal strength indicated by the multimeter will drop or disappear at the point of a wire break.

Multimeter performing line break point detection
Figure 6.8: Line break point detection using the intelligent high-precision sensor chip.

7. Specifications

The following table details the specifications for the ZL126/ZL128 series digital multimeters:

FeatureZL126AZL126BZL128AZL128B
Max Count6000 counts6000 counts9999 counts9999 counts
Power Supply3 * AAA batteries (not included)Built-in 1000mAh battery (USB)3 * AAA batteries (not included)Built-in 1000mAh battery (USB)
DC Voltage0.5V-600V (Auto), 0V-600V (Manual)0.5V-600V (Auto), 0V-600V (Manual)1V-1000V (Auto), 0V-1000V (Manual)1V-1000V (Auto), 0V-1000V (Manual)
AC Voltage1V-600V (Auto), 0V-600V (Manual)1V-600V (Auto), 0V-600V (Manual)1V-750V (Auto), 0V-750V (Manual)1V-750V (Auto), 0V-750V (Manual)
AC/DC CurrentNot supportedNot supported0mA-10A0mA-10A
Resistance0-10MΩ0-10MΩ0-100MΩ0-100MΩ
Capacitance0-6mF0-6mF0-100mF0-100mF
Frequency10Hz-1KHz10Hz-1KHz0-10MHz0-10MHz
True RMS40-400Hz40-400Hz0-1KHz0-1KHz
Ambient Temperature0℃~60℃0℃~60℃0℃~60℃0℃~60℃
Probe TemperatureNot supportedNot supported-50℃~1100℃-50℃~1100℃
Data RetentionYesYesYesYes
Firewire DetectionYesYesYesYes
NCV Voltage PenYesYesYesYes
NCV Analog StripYesYesYesYes
Color DisplayYesYesYesYes
Function IndicatorYesYesYesYes
FlashlightYesYesYesYes
Operation ModeAuto Mode + Manual ModeAuto Mode + Manual ModeAuto Mode + Manual ModeAuto Mode + Manual Mode
Package Dimensions150 x 50 x 20mm (5.91 x 1.97 x 0.79in)150 x 50 x 20mm (5.91 x 1.97 x 0.79in)150 x 50 x 20mm (5.91 x 1.97 x 0.79in)150 x 50 x 20mm (5.91 x 1.97 x 0.79in)
Package Weight280g (9.88oz)280g (9.88oz)280g (9.88oz)280g (9.88oz)

8. Maintenance

8.1 Cleaning

To clean the multimeter, gently wipe the casing with a damp cloth and a mild detergent. Do not use abrasive cleaners, solvents, or immerse the device in water.

8.2 Storage

Store the multimeter in a cool, dry place, away from direct sunlight and extreme temperatures. If storing for extended periods (for ZL126A/ZL128A models), remove the AAA batteries to prevent leakage.

8.3 Calibration

The multimeter is factory calibrated. If you suspect inaccuracies or require recalibration, please contact customer support or a qualified service center.

8.4 Test Lead Care

Regularly inspect the test leads for any signs of damage, such as cuts, cracks, or damaged insulation. Replace damaged test leads immediately to ensure safety and accurate measurements.

9. Troubleshooting

If you encounter issues with your multimeter, refer to the following common problems and solutions:

  • No Display/Power:
    • Check the batteries (ZL126A/ZL128A) or charge level (ZL126B/ZL128B).
    • Ensure batteries are inserted with correct polarity.
    • Press the power button firmly.
  • Inaccurate Readings:
    • Ensure test leads are properly connected to the correct jacks.
    • Verify that the correct measurement mode is selected for the task.
    • Check for damaged test leads, which can cause intermittent or incorrect readings.
    • Ensure the circuit is de-energized for resistance, capacitance, and diode tests.
  • No NCV Detection:
    • Ensure the NCV sensor is held directly over the live wire or source.
    • Try toggling the H/L sensitivity button.
    • Verify the battery level, as low battery can affect NCV performance.
  • No Continuity Beep:
    • Ensure the circuit is de-energized before performing a continuity test.
    • Check for open circuits or components with high resistance, which will not trigger the beep.

10. Warranty and Support

This product comes with a 12-month manufacturer's limited warranty for defective items from the date of receipt. Accessories are covered by a 3-month warranty. The warranty does not cover items damaged or misused after receipt.

For warranty claims or technical support, please contact your retailer or the manufacturer directly. You will need to provide your order number and a detailed description of the defect or issue.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.