1. Introduction
This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your JOYING 11.6" Car Stereo Radio Multimedia Player (Model: JY-HT117N8) designed specifically for Honda CRV models from 2012 to 2016. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.
2. Safety Precautions
2.1. General Safety
- When driving, adjust the sound volume to an appropriate level to perceive the driving situation and ensure safety.
- To ensure driving safety and comply with traffic laws, do not watch videos or operate the car radio while driving.
- To avoid short circuits, do not expose this unit to rain.
- To prevent short circuits, do not place or leave any metal objects (such as coins or metal tools) inside the car radio.
- Operate the car radio according to this manual. Do not open the audio system for repair. If repair is required, consult a professional repair station or contact the seller directly.
- Do not operate the car stereo for an extended time when the engine is off, as it will drain the battery.
- Do not insert objects into the ventilation slots or other openings on the car radio.
- Do not touch, rub, or strike the screen with sharp objects.
2.2. Maintenance Precautions
- The screen must not be polluted by moisture, dust, steam, or oily smoke.
- The screen must not be exposed to direct sunlight for long periods.
- The stereo must be protected from heavy pressure and impact.
- Do not connect other power sources to the car radio, as internal components may be burnt.
- If the screen is stained, clean it with a soft and clean cloth.
3. Package Contents
The package includes the following items:

Figure 3.1: Included Accessories
- Single Din Cage
- Left & Right Bracket
- WiFi Antenna (x1)
- GPS Antenna (x1)
- 4G Antenna (x2)
- External Mic (x1)
- USB Cable (x2)
- AR Cable (x1)
- Screen Ribbon Cable (x1)
- Power Cable (x1)
- User Manual (PDF reference available online)
4. Compatibility and Installation Guide
This multimedia player is designed for Honda CRV models from 2012 to 2016. Due to variations in factory configurations, it is crucial to identify your car's dashboard type to ensure you receive the correct wiring harness for plug-and-play compatibility.
4.1. Identifying Your Dashboard Type
Please refer to the image below to identify your car's dashboard type (A, B, C, D, or E) before proceeding with installation. The image displays the back of the factory player with disconnected plugs, not the JOYING radio itself.

Figure 4.1: Dashboard Purchase Guide
- Dashboard A: For 2012-2016 car dashboard with FM button, without factory amplifier.
- Dashboard B: For 2012-2016 car dashboard with FM/AM or FM/DAB button, with factory amplifier.
- Dashboard C: For 2012-2014 car dashboard, with screen.
- Dashboard D: For 2012-2014 car dashboard, with screen.
- Dashboard E: For 2015-2016 car dashboard, with DA screen.
4.2. General Installation Notes
- Not all connectors on the vehicle's original plugs need to be connected. Only connect the plugs suitable for your vehicle.
- After connecting, power on the device to check proper functionality. If any function is not working, contact support.
- This device does not support synchronizing the original car's IMID screen information by default.
4.3. Factory Feature Support
- Steering Wheel Control:
- Dashboards A, B, C, and D: Three "phone buttons" on the steering wheel may not work, but other SWC buttons will function.
- Dashboard E: All steering wheel buttons are fully supported.

Figure 4.2: Steering Wheel Control Compatibility
- Factory Reverse Camera:
- Dashboards A or B: The factory reverse camera will display on the original IMID screen, not on the JOYING head unit. To display on the JOYING unit, you may need to rewire the original car's cable or install a JOYING AR camera.
- Dashboards C, D, or E: The device supports the factory reverse camera.
- Factory USB Support:
- Dashboards A, B, C, and D: Factory USB is not supported.
- Dashboard E: One factory USB adapter is included by default. For both factory USB ports to work, contact the seller for two adapters. Note: Dashboard E does not support the factory HDMI port.
- Other Supported Features: Factory right view camera, factory amplifier, and subwoofer are supported.
4.4. Wiring Diagram and Connections
The following diagram illustrates the rear ports of the head unit. Ensure all necessary connections are made securely according to your vehicle's configuration.

Figure 4.3: Rear Panel Connections
Key Connections:
- AVM360 Camera: For 360-degree camera systems.
- WiFi Antenna: Connect the independent WiFi antenna for stable signal quality and fast internet access. Supports 802.11a/b/g/n/AC, 2.4GHz/5GHz.
- GPS ANT: Connect the GPS antenna for navigation.
- 4G DIV / 4G PRI: Connect 4G antennas for cellular data connectivity.
- Video IN: For external video sources.
- CEN OUT / SUB OUT: Center and Subwoofer audio outputs.
- Radio-ANT: Connect the car's radio antenna.
- USB: Multiple USB ports for data transfer, charging, and connecting accessories.
- MIC: External microphone input.
- HDMI OUT: Full digital image and sound output for projection screens or on-screen displays. Note: HDMI cable not included.
- Optical / Coaxial Out: Digital audio outputs.
- L IN / R IN: Left and Right audio inputs.
- RL OUT / RR OUT / FL OUT / FR OUT: Rear Left, Rear Right, Front Left, Front Right audio outputs.
- Power Port: Main power connection.
- Fuse: Integrated fuse for circuit protection.

Figure 4.4: HDMI Output

Figure 4.5: WiFi Antenna Connection
4.5. Screen Position and Depth Adjustment
The screen position and depth can be adjusted to fit various car center consoles and avoid obstructing air conditioning controls.
4.5.1. Screen Position Adjustment (Up/Down)
The screen can be moved up or down with a maximum movement distance of 24mm and a minimum movement distance of 8mm.

Figure 4.6: Screen Position Adjustment
When moving the screen up, remove the 4 clips behind the screen and adjust the distance to avoid covering the air conditioning buttons or vents. Move the clips to the right position after adjustment.
4.5.2. Screen Depth Adjustment
The screen depth can be adjusted by modifying the screw holes of the components. The minimum adjustment range is 5mm, and the maximum is 10mm.

Figure 4.7: Screen Depth Adjustment
5. Operating Instructions
5.1. Basic Operation - Gesture Recognition
The car radio recognizes various gestures including short press, long press, drag, and slide. These functions are for reference, and details may vary slightly by car radio model.
Gesture Types:
- Click: Short press to select or activate.
- Drag: Press and hold, then move.
- Press: Long press for additional options.
- Swiping up and down: Used for scrolling through lists or content.
- Swipe left: Used for navigating between screens or closing elements.
The notification bar can be accessed by swiping your finger down from the status bar.
5.2. Main Interface
Press the home button on the status bar to display the home page. The main interface provides quick access to key functions.

Figure 5.2: Main Launcher Interface
- Click the home icon to enter the home page.
- Click the back arrow to return to the previous layer.
- Volume display: Adjust the system volume.
- Click the 'X' icon to close the current application.
- Click the square icon to view all applications.
- Click the gear icon to enter the settings.
- Long press an APP icon at the bottom of the home page to set it as a shortcut.
5.3. Split-screen Multitasking
The device supports split-screen multitasking, allowing you to use two applications simultaneously, such as navigation and video playback.

Figure 5.3: Split-screen Multitasking
- Tap the recent apps icon.
- Find the app you want to run in split-screen, click the icon to bring up the split-screen button, and tap it.
- The first app you have selected will display on the left side, then choose the second app in recent apps.
Video 5.1: Demonstration of Split-screen Multitasking and UI Responsiveness
5.4. Wallpaper and Personalization
Customize your device's appearance with various wallpaper and button color settings.

Figure 5.4: Personalized Settings
5.4.1. Wallpaper Setting
- System wallpapers are categorized into "light color" (day mode) and "dark color" (night mode).
- Select a wallpaper to apply it as the screen background.
- For custom wallpapers, set the picture resolution to match the car radio's screen resolution (e.g., 1920x1080). Save day mode pictures (light tone) and night mode pictures (dark tone) in JPEG or PNG format.
- To import custom wallpapers:
- Create a folder named "wallpapers" in the root directory of a USB disk.
- Inside "wallpapers", create "day" and "night" folders.
- Inside "day" and "night" folders, create a folder named "1920x1080" for horizontal wallpapers.
- Copy day mode pictures to the "day/1920x1080" folder and night mode pictures to the "night/1920x1080" folder.
- Insert the USB drive into the head unit, open the "Wallpaper" APP, click "import", then "search" for "Start position", and "Start copying" to complete the import.
5.4.2. Colorful Lights Setting
- Button light control: Set to "normally off", "always on", or "auto".
- Colorful light mode: Choose "manual" or "auto". In manual mode, select one of seven colors or adjust RGB values. In auto mode, button lights change color automatically.
- Adjust "Magic Mode Speed" to change the transition time of colorful lights.
5.5. Radio (FM/AM)
Access and manage your favorite radio stations.
- FM/AM Radio: Drag left and right in the frequency area to quickly find desired frequencies.
- Stereo/mono switch: Toggle between stereo and mono reception.
- Station name info: Easily edit station names for better organization.
- Adjust station: Long press to halve the frequency for automatic channel search.
- Last/Next station: Navigate between stations.
- Play and pause: Control radio playback.
- LOC (Local) / DX (Distance): LOC for short-range strong channels, DX for long transmission distances.
- AF (Alternative Frequencies): When on, the system automatically jumps to a station with good signal.
- TA (Traffic Announcement): When on, traffic announcement information will be automatically played.
- PTY (Program Type): Select station type for auto-search.
- Favorite stations: Long press any channel in the right list to save it as a favorite.
5.6. Bluetooth
Connect your mobile phone for calls and music streaming.
5.6.1. Bluetooth Dial
- Use the dial pad to make calls.
- View call history.
- Access phone book (requires synchronization).
- Answer/hang up calls.
- Microphone mute function.
5.6.2. Bluetooth Settings
- Click the Bluetooth APP to enter the settings interface.
- Toggle Bluetooth on/off.
- Change device name and pairing password (PIN).
- Set auto-answer for calls.
- Turn on/off WeChat voice switch for message prompt tone.
- Click "Search Devices" to find and connect to Bluetooth devices.
5.6.3. Bluetooth Music Playback
After connecting your phone to the car radio via Bluetooth, click the Bluetooth music APP to enter the player page.
- Navigate to the mixer page.
- Control playback: last song, pause/play, next track.
5.7. Video Player
Play videos from various sources.
- Picture-in-picture function.
- Loop playback (single loop / random playback).
- Navigate between videos: last video, next video.
- Add to favorite shows.
- Access file list.
5.8. Sound Effects
Customize your audio experience with advanced sound settings.
5.8.1. HiFi Settings
- Enter the "Sound effects" APP.
- Select speaker channel (2ch, 2.1ch, 4ch, 4.1ch, 5.1ch).
- Enable or disable DTS sound effect.
5.8.2. EQ Selection and Setting
- Enter EQ settings from the sound effects interface.
- Choose from 20 preset sound effects (e.g., Standard, Rock, Soft, Classical, Popular, Hall, Jazz, Theater, News, Electronic sound).
- Tap "Simple Mode" or "Complex Mode" for equalizer adjustments.
- The 48-band equalizer allows fine-tuning. Adjust Q value gain (High/Medium/Low).
- Three groups of user memory equalizer adjustments are available.
- "Simple mode" sets sound effects for front and rear speakers separately.
- "Complex Mode" sets sound effects for each speaker independently.
- Click the reset icon to restore default values.
5.8.3. Sound Field Settings
- Choose standard, main driving mode, co-driver mode, or full car mode.
- Adjust the desired sound field manually.
- Click the reset icon to restore default values.
5.8.4. DTS Scenes and Professional Settings
- DTS Scenes: Choose from 5 preset DTS scenes (Cinema mode, Dedicated mode, Music mode, MONO mono mode, LCRS single surround mode).
- Virtual Center: Set center audio output on/off (DTS must be off).
- Surround Mode: Adjust surround effect for 5.1 speakers.
- Bass Boost: Adjust low-frequency output for front/rear speakers and subwoofer.
- Sound Field Focus: Adjust sound pitch for front, middle, and rear speakers.
- Subwoofer: Adjust subwoofer output. "Phase" switch inverts output audio.
- Professional Settings:
- Delay Function: Set delay effect for speakers in different positions.
- Gain Adjustment: Increase speaker volume in different positions.
- X-over: Frequency division function for front, middle, and rear speakers.
5.9. Car Settings
5.9.1. Link Settings (Network & Connectivity)
- WiFi: Turn on WiFi, search for hotspots, and connect.
- Mobile network: Activate data flow of the SIM card to connect.
- Hotspot and network sharing: Share network via WLAN after inserting a SIM card.
- Bluetooth: Connect mobile phones to the car radio via Bluetooth.
5.9.2. Common Settings
- Navigation settings:
- Enable/disable navigation on boot.
- Set a third-party navigation app as default.
- View real-time satellite positioning status.
- USB settings:
- Set USB interface type (USB1.1 or USB2.0).
- Enable/disable USB music autoplay.
- Detection settings:
- Turn off handbrake detection to watch videos while driving (not recommended for safety).
- Turn off headlight detection to prevent screen brightness control by headlights.
5.9.3. Button Learning
- Open/close the floating shortcut key.
- Calibration Study: Calibrate the touch screen if offset appears. (Tip: Press 5 fingers on the screen for 10 seconds to enter calibration interface).
- Key Study: Learn and set touch screen buttons.
- Steering wheel keys learn: Program SWC buttons if your car has factory steering wheel control.
- Panel key learning: Set physical buttons on the panel.
- Panel knob settings: Configure physical knobs.
5.9.4. Gesture Learning
- Configure four two-finger gestures: "slide up", "slide down", "slide left", and "slide right".
- Set gesture control actions (e.g., mute, volume up/down, previous/next song, navigation, home, back, screen off).
- Adjust gesture volume step value (e.g., 1 or 5).
5.9.5. Sound Settings
- Beep sound: Turn on/off touch screen sound, select type, and adjust volume.
- Host volume: Set default car radio volume on boot.
- Bluetooth volume: Set default Bluetooth volume.
- Navigation mixing ratio: Set volume ratio of navigation voice and background music.
- Reverse mute: Turn on/off as needed.
- BT ringtone volume: Adjust Bluetooth ringtone volume for phone calls.
- MIC gain: Adjust microphone volume during Bluetooth phone calls.
5.9.6. Reverse Setting
- Reverse radar: Display radar information when reversing (requires Canbus support).
- Guide line: Display guide lines when reversing (requires Canbus support). Two trajectory line styles available.
- Reversing camera system: Select "Normal N system" for original cameras. Aftermarket cameras may need different standards.
- Mirror: Turn on/off mirror option based on camera installation.
- Backup camera power supply: Set to "often power on" or "power on when reversing".
5.9.7. AUX Setting
- Right view and AUX: Turn on right camera switch and floating button. Right-view camera can be activated by clicking the floating button.
- AUX/right camera: Select "CVBS N" for original car camera. Aftermarket cameras may need different standards.
- Live navigation: For AR camera system, select "Normal N system".
5.9.8. System Settings & Version Information
- Screen brightness: Adjust day and night mode brightness separately.
- Theme set: Choose "Light", "Dark", "Time Control", and "small light control".
- Theme: Select UI1 or UI2.
- Language and input method: Change system language.
- Date and time: Auto sync with network/GPS or manual setting.
- Time format: Set 12-hour or 24-hour format.
- System recovery: Restore to factory settings.
- Version Information: View system version, CPU, memory, storage, screen resolution, and software details.
5.10. Mobile Internet Operation
5.10.1. Z Link (Wireless/Wired CarPlay/Android Auto)
Connect your smartphone for seamless integration with CarPlay or Android Auto.
- Wireless Connection (iPhone & Android):
- Connect your phone to the car radio via Bluetooth.
- Open the "Z Link" app. Select "CARPLAY" for iPhones or "ANDROID AUTO" for Android phones.
- For iPhone: Click "Use CarPlay" when prompted. For Android: Click "confirm" when prompted.
- Wired Connection (iPhone & Android):
- Connect your phone to the USB OTG port of the car radio using the original data cable.
- Open the "Z Link" app. Choose the connection method (CarPlay/Android AUTO/HUAWEI HiCar/MIRROR).
- For iPhone: Click "allow" when prompted to use CarPlay. For Android: Click "confirm" when prompted.

Figure 5.5: CarPlay Interface

Figure 5.6: Android Auto Interface
5.10.2. Mirror Wireless Screen Connection
- Connect your phone and the head unit to the same WiFi network, or connect the head unit to your mobile hotspot.
- Click the mirror interface icon, select "MIRROR" to enter the wireless screen projection interface.
- Open your mobile phone's control center, select Screen Mirroring, and choose the car device name to start screen mirroring.
5.10.3. CarPlay Play Video (iPhone iOS 18+)
- Connect iPhone (iOS 18 or above) to wireless CarPlay.
- Click "Kolos" to enter the video playback interface.
- Download the Kolos app on your mobile phone.
- Turn on phone mirroring and connect to a device starting with "zLink-***".
- Open the app and click [video stream].
- Screen projection should be successful.
- Select the video to play on your mobile phone.
5.11. Car Logo Setting
Set a customized boot-up logo for your device.
- Prepare a logo picture (e.g., 1280*800, 1920*1080 resolution) named "Logo.BMP".
- Create a folder named "Medialogos" on an empty USB disk and place "logo.bmp" inside.
- Insert the USB disk into the car radio. Go to Settings > System > Factory (password: 8888) > Set boot logo to view the logo picture.
- For dynamic logos or file upgrades, contact support.
6. Troubleshooting (FAQ)
This section addresses common issues and their solutions.
6.1. Head Unit Doesn't Turn On / Black Screen
- After installation (first boot): Click the reset button to restart the device.
- After some time of use: Check if the radio has sound (touch screen prompt, music playback). If so, open the radio cover (with support guidance) and check for a red flashing light on the core board.
6.2. Poor FM Radio Reception
- Check if the OEM car radio antenna requires power and if the ANT-CONT Cable is connected.
- Go to Factory Settings and switch on "Antenna Always on".
6.3. No Sound / Some Speakers Without Sound
- Car with OEM Amplifier: Connect the AMP-CONT Cable and turn on "AMP ON/OFF" in Sound Setting.
- Car without OEM Amplifier: Check if power cables (especially speaker cables) are well connected. Try re-plugging cables.
- If sound is lower, check Volume Balance settings and set volume to middle level.
6.4. Reversing Camera Issues
- Head Unit switches to reverse mode but no signal/black screen:
- Check trigger wire and power supply cable connections.
- Verify camera condition: Connect camera to "Video In" port and open AUX APP to check image.
- Head Unit cannot switch to reverse mode:
- Car without Canbus: Check Back Cable connection. If radio switches to reverse mode after connecting Back Cable to red ACC Cable, it means Back Cable was not connected to car reversing light correctly.
- Car with Canbus: Remove Back Cable and connect to red ACC Cable. If radio switches to reverse mode, the Canbus adapter is defective.
6.5. GPS Not Working / Without Signal
- Check if the GPS antenna is connected correctly or securely.
- Ensure GPS antenna receiver is in a correct and reasonable position (receiver side facing sky, no metal shielding).
6.6. Bluetooth Connection Issues
- Radio supports Bluetooth connection only with Phone and OBD2.
- If connection fails, switch off Bluetooth on both phone and head unit, then switch on and try again.
- Pay attention to pop-up prompts on your phone and click "Yes".
6.7. Bluetooth Phone Call Audio Issues
- Others cannot hear user clearly:
- If using external microphone, check if it's connected properly. Re-plug if necessary.
- Record voice with recording APP and listen. If clear, microphone is good; otherwise, it's defective.
- Users hear others' voice too low:
- Adjust head unit's main volume.
- Adjust Microphone volume in sound settings.
6.8. Bluetooth Music Playing Without Sound
- Check if phone's volume is normal and turn it up.
- Check if phone's Bluetooth is switched on for audio permissions.
6.9. Contacts Display Issues
- Check if "Sync contacts" is turned on in phone's Bluetooth settings.
- Contacts info must be saved in phone, not SIM Card, to sync.
6.10. Bluetooth Name Change Failed
If the Bluetooth name is not updated, turn off Bluetooth, turn it on again, then search and connect.
6.11. SD Card / USB Music Files Not Updated
- After inserting SD Card or USB, go to music app to detect and scan dates. Large data may take time to update.
- If no update, ensure SD Card/USB is inserted correctly and files are visible in Filemanager app. Reinsert or check the card/device.
6.12. USB Not Recognized / Abnormal Reading
- Try different brands and storage USB disks.
- If USB disk reading is abnormal, troubleshoot on computer, then format after backing up.
6.13. Unable to Connect to CarPlay / Android Auto
- Wired CarPlay/Android Auto: Use the OEM USB Cable to connect to the radio OTG USB port. Third-party cables may not ensure support. For Samsung phones, use OEM USB Cable.
- If a reminder pops up on your phone, click "Trust".
- Wireless CarPlay/Android Auto: Restart your phone and try again.
6.14. WiFi Cannot Connect Automatically to Phone's Hotspot
If using an iPhone, you must enter the "Personal hotspot" page on your phone. Otherwise, the head unit cannot search your phone hotspot.
6.15. Touch Screen Not Working (Freezes / No Reaction)
- Reset the head unit first.
- Try connecting a USB Mouse. If it works, the touch screen is broken. If not, the core board is defective.
6.16. SIM Cards Not Recognized
- Ensure micro SIM Card is inserted correctly.
- After inserting, click the reset button to reset the radio.
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | JOYING |
| Joying Model | JY-HT117N8 |
| Operating System | Android 13 |
| Processor Type | Qualcomm Snapdragon 6125 |
| RAM | 8G |
| ROM | 128G |
| Display Size | 11.6 inch |
| Resolution | 1920*1080 |
| Touch Screen | Yes |
| Built-in Screen | Yes |
| Out Power | 4*50W |
| Voltage | 12 V |
| Item Weight | 4.0kg |
| Max External Memory | 128G |
| TF/Micro SD Slot | 1 |
| Din | One Din |
| Interface | USB/RCA |
| Digital Media Format | Mp3, MP4, WMA, JPEG |
| Wireless Carplay/Android Auto | Support |
| AfterMarket Rear/Front Camera | Support |
| Positioning System | GPS/GLONASS/BEIDOU |
| Factory Steering wheel control | Support |
| Factory Amplifier | Support |
| Factory Rear Camera | Support |
| Factory USB port | Support (Only For C option) |
| Factory Lanewatch Camera | Support |
| Material | metal+ABS |
| OSD Language | Multi-language support including English, Chinese, German, French, Spanish, etc. |

Figure 7.1: Key Features Overview

Figure 7.2: System Overview and Supported Features
8. User Tips
- OBD2 Connectivity: The unit supports an optional OBD2 module for retrieving real-time data and trouble codes. This is not included in the standard package.
- Reverse Camera for Dashboard D: For cars with Dashboard D, the factory reverse camera is supported. Ensure the correct adapter cable is used if provided, or check wiring if using an aftermarket camera.
- Screen Cleaning: Use a soft, clean cloth for cleaning the screen to avoid scratches and maintain clarity.
- Firmware Updates: Periodically check the manufacturer's website or contact support for firmware updates to ensure optimal performance and access to new features.
9. Warranty and Support
9.1. Warranty Information
This product comes with a 2-year manufacturer's warranty. All items are tested multiple times to ensure proper functionality before shipping.
The warranty does not cover damages resulting from:
- Improper installation
- Accident
- Misuse or abuse
- Improper wiring
- Incorrect voltage operation
- Operating the unit against the instructions in this owner's manual
For warranty claims or repairs, please contact the seller directly.
9.2. User Manual (PDF)
A detailed user manual in PDF format is available for download. You can access it via the following link: JOYING Car Stereo User Manual PDF.