Instruction Manual: Robotic Vacuum Cleaner Replacement Parts

Introduction

This manual provides essential information for the installation, maintenance, and troubleshooting of your new replacement parts for robotic vacuum cleaners. These parts are designed to be compatible with various models, ensuring your device continues to operate efficiently. Please read this manual carefully before installation and use.

Applicable Models

These replacement parts are compatible with the following robotic vacuum cleaner models:

• MAMNV BR150, BR151
• ZCWA BR150, BR151
• ONSON BR150, BR151
• MANVINS G20
• Cecotec Conga 999 Origin X-Treme
• Cecotec Conga 999 Origin Genesis

Important: Always verify your specific device model number on the nameplate at the bottom of your vacuum cleaner to ensure compatibility.

Underside view of a compatible robot vacuum cleaner, showing the location for brush, mop, and filter installation.

Package Contents

The specific quantity and type of parts you receive are determined by your order selection. A typical package may include:

• Side Brushes
• Mop Pads
• HEPA Filters
• Small Cleaning Tool (for brush maintenance)

Example package contents including two filters, two side brushes, two mop pads, and a small cleaning tool.

Setup and Installation

Follow these general steps to replace your vacuum cleaner parts. Always refer to your specific vacuum cleaner's manual for detailed instructions if available.

1. Safety First

• Ensure your robotic vacuum cleaner is turned OFF and unplugged (if applicable) before attempting any installation or maintenance.
• Place the vacuum cleaner upside down on a clean, flat surface.

2. Replacing Side Brushes

• Locate the existing side brushes on the underside of your vacuum.
• Gently pull the old brushes upwards to remove them. Some models may require unscrewing a small screw.
• Align the new side brushes with the corresponding 'L' (Left) and 'R' (Right) markings on the brush and the vacuum cleaner.
• Press the new brushes firmly into place until they click, or secure with screws if necessary.

Diagram illustrating the installation of side brushes, showing 'L' and 'R' markings for correct placement.

3. Replacing Mop Pads

• Remove the water tank or mop attachment from your vacuum cleaner.
• Detach the used mop pad from the attachment (usually Velcro or a sliding mechanism).
• Attach the new microfiber mop pad, ensuring it is securely fastened and covers the entire surface of the mop attachment.
• Reinstall the water tank or mop attachment onto the vacuum cleaner.

Close-up of a microfiber mop pad, highlighting its texture and attachment points.

4. Replacing HEPA Filters

• Open the dustbin compartment of your vacuum cleaner.
• Remove the dustbin and locate the filter assembly.
• Carefully remove the old filter, tapping it over a trash can to dislodge any loose debris.
• Insert the new HEPA filter into the designated slot, ensuring it is seated correctly to maintain proper filtration.
• Close the dustbin compartment and reinsert the dustbin into the vacuum cleaner.

Maintenance

Regular maintenance of your replacement parts will extend their lifespan and ensure optimal cleaning performance.

Side Brushes

• Periodically check side brushes for tangled hair or debris. Use the provided cleaning tool or scissors to remove any obstructions.
• If bristles become bent or worn, consider replacing the brushes to maintain effective edge cleaning.

Mop Pads

• After each use, remove and wash the mop pad. All mop pads in this kit are washable.
• Allow mop pads to air dry completely before reattaching them to prevent mildew or odors.

HEPA Filters

• After every few cleaning cycles, remove the filter from the dustbin and gently tap it against a trash can to remove accumulated dust and debris.
• The filters are washable. Rinse them under running water, ensuring all dust is removed.
• Allow the filter to air dry completely for at least 24 hours before reinstalling it. Do not use a dryer or direct heat.
• Replace filters every 1-3 months, depending on usage and household environment, to maintain optimal filtration efficiency.

Diagram showing the filtration process of the HEPA filter, capturing dust, dust mites, allergens, and mold.

Image of a washable HEPA filter, emphasizing its pleated design for efficient air purification.

Specifications

Troubleshooting

• Parts do not fit: Double-check your vacuum cleaner's model number against the list of compatible models. Ensure you have purchased the correct set of parts.
• Reduced cleaning performance: Verify that all parts are installed correctly and securely. Clean brushes and filters regularly as per the maintenance section. Replace worn-out parts promptly.
• Unusual noises: Inspect brushes for tangled hair or debris that might be causing friction. Ensure brushes are properly seated and not obstructed.

User Tips

• Always confirm your specific robot vacuum model number (e.g., MAMNV ZCWA ONSON BR150/BR151 MANVINS G20) before purchasing replacement parts to ensure perfect compatibility.
• Regularly clean all components, especially filters and brushes, to maintain your vacuum's suction power and extend the life of the parts.
• Keep a spare set of filters and brushes on hand for quick replacements, especially if you have pets or allergies.

Warranty and Support

For any issues, questions, or concerns regarding your replacement parts, please contact the seller directly through the platform where you made your purchase. Provide your order details and a clear description of the problem for prompt assistance.

Important Notices

• These products are brand new compatible replacement parts and are not genuine/original products from brands like Xiaomi, Roborock, iLife, Dyson, iRobot, 360, Ecovacs, or Conga.
• The quantity and specific items you receive are based on the options selected during your order, not necessarily all items shown in promotional images or titles.
• If you request a refund due to purchasing the wrong product, you may be responsible for return shipping costs.
• In case of a lost or broken package during transit, please contact the seller immediately for a resolution.