CADA Modification Accessories for CADA C61042 C61043

Contents

Instruction Manual

Car Modification Accessories for CADA C61042 C61043 MOC Building Blocks

1. Product Overview

This product provides various modification accessories for CADA C61042 and C61043 MOC building block car models. These accessories allow for customization of the car's appearance, including body color changes, wide body kits, tail wings, engine detailing, and LED lighting. Please note: The car model itself is not included. This package contains only the modification accessories.

Red and black car models illustrating color modification

Figure 1.1: Example of car body color modification from red to black.

The accessories are made from environment-friendly ABS plastic, suitable for users aged 12 and above.

2. Package Contents

Depending on the selected modification kit, your package may include:

  • Car body color modification parts (e.g., black parts to replace red parts)
  • Wide body kit components
  • Tail wing set components
  • Engine modification parts (e.g., hubs, tyres, brake discs, engine cylinders, electroplated or painted engine plates)
  • LED light set with remote control
  • Various small connectors and pins
Overview of various black modification accessory packages

Figure 2.1: General overview of modification accessory packages.

Components for tail wing and wide body kit

Figure 2.2: Components for tail wing and wide body kit.

Components for hubs, tyres, brake discs, and engine cylinders

Figure 2.3: Engine modification components including hubs, tyres, brake discs, and engine cylinders.

3. Setup and Installation

Follow these general steps for installing the modification accessories. Specific instructions for your car model (CADA C61042 or C61043) may vary slightly. Refer to your car model's original manual for disassembly guidance.

3.1. Car Body Color Modification

  1. Carefully disassemble the existing car body panels of your CADA model.
  2. Identify the corresponding black replacement parts from your modification kit.
  3. Important: Refer to the diagram below for specific parts that should be replaced with black parts, and those red parts that should be retained.
  4. Assemble the new black body panels onto your car model.
Diagram showing which red parts to replace with black parts, with exceptions

Figure 3.1.1: Diagram for replacing red parts with black parts. Note the specific red parts (42x, 4x, 4x, 156x, 8x, 5x) that should still be used.

Before and after modification of car body and wide body

Figure 3.1.2: Visual comparison of car body before (red) and after (black with wide body) modification.

3.2. Wide Body and Tail Wing Installation

  1. Attach the wide body fender flares to the wheel arches of your car model. Ensure they are securely fastened using the provided connectors.
  2. Assemble the tail wing components as shown in the product images.
  3. Mount the assembled tail wing to the rear of your car model.
Components for tail wing and wide body, with after modification examples

Figure 3.2.1: Tail wing and wide body components and their post-installation appearance.

Tail wing set components and post-installation display

Figure 3.2.2: Tail wing set components and post-installation display on a black car model.

3.3. Engine Modification

Replace the standard engine components with the detailed modification parts. This may include:

  • New hubs, tyres, and brake discs for enhanced wheel appearance.
  • Detailed engine cylinders and exhaust pipes.

Choose between electroplated or painted engine plate options for different aesthetic finishes.

Close-up of engine modification with silver pipes and gold sphere

Figure 3.3.1: Example of engine modification with silver pipes (electroplated).

Close-up of engine modification with electroplated red pipes and sphere

Figure 3.3.2: Electroplated engine plate option. Note: Original red parts may be replaced with metallic gold/electroplated red in actual shipment.

Close-up of engine modification with painted black pipes and sphere

Figure 3.3.3: Painted engine plate option.

3.4. LED Light Set Installation

  1. Identify the locations for the LED lights on the front, rear, and sides of your car model.
  2. Carefully integrate the LED light components into the building blocks, ensuring wires are neatly tucked away to avoid damage.
  3. Connect the LED lights to the power source (e.g., battery box, not included unless specified).
  4. Ensure the remote control is paired with the light set according to its specific instructions (if provided separately).
LED light set components

Figure 3.4.1: Components of the LED light set.

Red car model with LED lights on the front, showing a remote control

Figure 3.4.2: Front view of the car with installed LED lights and remote control.

Red car model with LED lights on the rear

Figure 3.4.3: Rear view of the car with installed LED lights.

Red car model with LED lights on the side

Figure 3.4.4: Side view of the car with installed LED lights.

4. Operating the LED Light Set

If your kit includes the LED light set, operate it using the provided remote control.

  • Power On/Off: Use the designated button on the remote to turn the lights on or off.
  • Mode Selection: Cycle through different lighting modes (e.g., steady, flashing) using the mode button.
  • Brightness Adjustment: Adjust the brightness levels as desired.

Video 4.1: Demonstration of the LED light set in operation.

5. Maintenance

  • Cleaning: Use a soft, dry cloth to gently wipe the accessories. Avoid harsh chemicals or abrasive materials that could damage the plastic or painted/electroplated surfaces.
  • Storage: Store unused or disassembled parts in a cool, dry place away from direct sunlight to prevent material degradation.
  • Handling: Handle all parts with care to avoid breakage, especially small connectors and delicate LED components.

6. Troubleshooting

  • Parts not fitting: Double-check the instructions and ensure you are using the correct parts for the intended location. Some parts may require gentle force to snap into place.
  • LED lights not working:
    • Ensure batteries (if applicable) are correctly installed and charged.
    • Check all wire connections to ensure they are secure.
    • Verify the remote control has working batteries and is properly paired.
  • Missing parts: Carefully check all packaging. If parts are genuinely missing, contact customer support.

7. Specifications

Feature Detail
Material Plastic (ABS)
Puzzle Style 3D PUZZLE
Recommended Age 12+ years
Gender Unisex
Origin Mainland China
Approx. Package Weight 0.4 kg
Approx. Package Dimensions 12 cm (L) x 8 cm (W) x 10 cm (H)

8. User Tips

  • Always refer to the original CADA car model's instruction manual for detailed disassembly and assembly steps before installing modification parts.
  • Organize all small parts before starting installation to prevent loss.
  • Test the LED light set functionality before fully integrating it into the model to ensure all connections are correct.
  • For a cleaner look, use small cable ties or adhesive to manage LED wires within the model.

9. Support

For any questions, concerns, or assistance with your modification accessories, please contact the seller or manufacturer directly. Provide your order details and a clear description of the issue for prompt support.

Disclaimer: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.