Introduction
This manual provides comprehensive instructions for the safe and efficient operation of your RETEVIS RT29D DMR Walkie Talkie. Please read it thoroughly before use to ensure optimal performance and to understand all safety precautions.

The RT29D features 10W High Power, IP67 Waterproof rating, a 3200mAh Battery, and supports both Digital & Analog Modes.
Main Functions and Features
- High / Middle / Low Power Adjustable
- English / Chinese Voice Prompts
- Monitor Function
- 8 Zones * 16 Channels (128 total channels)
- Power Save / Low Power Alarm
- Squelch Level 1-10
- Electricity Inquiry
- Sound Tail Elimination
- Programmable Side Keys
- TOT (Time-Out Timer)
- Encryption (32-bit ensures communication security)
- Channel Scan
- Talk Around / Repeater Function
- Wide / Narrow Bandwidth Selection
- Bluetooth Function (optional)
- Digital & Analog Mode compatibility
- Single/Group/All Call capabilities
- Dual Time Slot for duplex communication
Unpacking and Checking Equipment
Before using your transceiver, please follow these steps:
- Check the packing box for any signs of damage.
- Carefully unpack the box and verify that all items listed below are included.
- If any item is missing or damaged, please notify your dealer.
Supplied Accessories
| Commodity | Quantity |
|---|---|
| Transceiver | 1 |
| Antenna | 1 |
| Battery | 1 |
| Battery Charger | 1 |
| Belt Clip | 1 |
| Hand Strap | 1 |
| User Manual | 1 |
| Bluetooth Earphone (Optional) | 1 |
Note: The package contents may vary slightly depending on whether you purchased the Bluetooth version or non-Bluetooth version. For example, the non-Bluetooth version includes a User Manual (PDF) and the Bluetooth version includes a Bluetooth headset and charging cable.

Non-Bluetooth version package includes: Walkie Talkie, Antenna, Hand Strap, Belt Clip, Battery, Charging Base, Adapter, User Manual.

Bluetooth version package includes: RT29D Walkie Talkie, Antenna, Battery, Charging base, Hand Strap, Belt Clip, Charging Cable, Bluetooth earphone, Adapter, User Manual.
Battery Information and Charging
Charging the Battery
Use only the official charger provided by RETEVIS. Follow these steps to charge the battery:
- Connect the charger to a power supply socket.
- Install the battery or the transceiver with the battery into the charger. The red light indicates charging is in progress.
- When the red light turns off and the green light turns on, the battery is fully charged.
- Unplug the charger from the power supply socket and remove the battery.
Note:
- Do not continue charging once the battery is full, as this will shorten its lifespan.
- The ambient temperature for charging should be between 5°C and 40°C.
- Ensure battery contacts are clean before charging.
- Turn off the radio before charging.
- Do not charge a wet battery or radio; dry it first.
- If the battery capacity does not return to normal after proper charging, it indicates the battery life has ended and it should be replaced.
Battery Type and Safety Precautions
Always use the official RETEVIS battery. Using other battery types may cause explosion and injury.
- Do not throw batteries into fire.
- Do not attempt to disassemble the battery pack housing.
Battery Storage
- For long-term storage, fully charge the battery first to prevent damage from excessive self-discharge.
- Recharge the battery after 6 months of storage to prevent excessive self-discharge and capacity reduction.
- Store the battery in a cool, dry environment to minimize self-discharge.

The 3200mAh battery provides approximately 14 hours of working time and 46 hours of standby time, with a 6-hour charging time.
Install and Remove Accessories
Install/Remove Battery Pack
Note:
- Do not short circuit battery pack terminals or throw battery pack into fire.
- Do not try to remove the battery pack shell.
- Do not install battery pack under dangerous conditions, otherwise spark will cause explosion.

To install the battery pack, insert the top part into the transceiver's top two slots, then press the bottom buckle.

To remove the battery pack, ensure the transceiver is off, open the bottom buckle, and take out the battery.
Install Antenna
Hold the base of the antenna and rotate it tightly clockwise into the connector at the top of the transceiver.
Install/Remove Belt Clip
If necessary, install the supplied screws into the belt clip at the back of the battery pack. To remove, simply unscrew the two screws.
Install Hand Strap
Install the hand strap at the middle circle of the transceiver.
Getting Started: Transceiver Overview

Key components of the RT29D Walkie Talkie and optional Bluetooth earphone.
- Antenna: For transmitting and receiving signals.
- Channel Knob: Used to select the desired communication channel.
- Power/Volume Knob: Turns the radio on/off and adjusts the volume.
- Status Indicator: Displays the radio's operating status.
- Speaker: Outputs received audio.
- PTT (Push-to-Talk) Key: Press to transmit, release to receive.
- Microphone: For speaking into the radio.
- Side Key 1 & 2: Programmable keys for various functions (e.g., Monitor, Zone Selection, Power Level).
- Earpiece Jack: For connecting external audio accessories.
Basic Operations
Power On and Power Off
Rotate the Power/Volume knob clockwise until a "click" is heard. The transceiver will emit a short beep, indicating successful power-on. To power off, rotate the knob anticlockwise until a "click" is heard.
Adjust Volume
With the transceiver powered on, rotate the Power/Volume knob to adjust the volume. Clockwise rotation increases volume; anticlockwise rotation decreases volume. A programmed MONITOR side key can also be used to check the current volume.
Channel Selection
Rotate the Channel knob to select one of the 128 available channels. The transceiver supports 8 zones, each with up to 16 channels, selectable via a pre-programmed key.
Transmit
To transmit, press and hold the PTT key. Keep the microphone 3-4 cm from your mouth and speak in a normal tone.
Receive
Release the PTT key to receive. Adjust the volume for optimal reception.
Function Specifications
LED Indicator
- Red light: Transmitting.
- Green light: Powering on or receiving non-encrypted signals/data.
- Blue light: Bluetooth is powered on.
Call (PTT) Key
Each channel can be set as a digital channel. Continuous pressing of the PTT key during transmission sends signals to other transceivers. Press PTT to transmit and release to receive; the microphone activates with PTT press.
Receive and Transmit Call
Zone Selection
The transceiver supports up to 8 zones, each with a maximum of 16 channels.
- Press the pre-programmed Zone key.
- You will hear a "confirmed" tone, and each press cycles through zones from low to high.
- Rotate the channel knob to select the desired transmitting channel.
Receive and Reply Call
You can receive or reply to calls after setting the channel/user ID or group ID. The LED indicator turns red when transmitting and green when receiving.
Receive and Reply Group Call
To receive a group call, the transceiver must be configured to belong to that group.
- LED indicator turns green.
- Hold the transceiver vertically, 2.5-5.0 cm from your mouth.
- Press PTT to respond to the call (LED indicator turns red).
- Release PTT to receive.
Receive and Reply Individual Call
Private calls are one-to-one. When receiving a private call, the LED indicator turns green. Hold the transceiver vertically 2.5-5.0 cm from your mouth. Press PTT to respond (LED indicator turns red), then release PTT to receive.
Receive All Call
An All Call is a broadcast to all transceivers on the same channel. When received, the LED indicator turns green. Note: Switching channels during an All Call will stop reception. No re-programmed keys can be used until the All Call ends.
Launch a Transceiver Call
You can initiate calls using the Channel Knob, User ID, or Talking Group ID.
Launch a Group Call
- Rotate the channel knob to select the talking group using the activated group ID.
- Hold the transceiver vertically, 2.5-5.0 cm from your mouth.
- Press PTT to launch the call (LED indicator turns red).
- Release PTT to receive. The LED indicator turns green when the target transceiver responds.
Launch a Private Call
- Rotate the channel knob to select the channel using the activated user's ID.
- Hold the transceiver vertically, 2.5-5.0 cm from your mouth.
- Press PTT to launch the call (LED indicator turns red).
- Release PTT to receive. The LED indicator turns green when the target transceiver responds.
Launch All Call
This function allows transmission to all users on the same channel. The transceiver must be programmed for this function.
- Rotate the channel knob to select the channel using the activated All Call talking group ID.
- Hold the transceiver vertically, 2.5-5.0 cm from your mouth.
- Press PTT to launch the call (LED indicator turns red).
Scan Function (Carrier Scan)
- Use programming software to set PF1/PF2 as the scan function.
- Long press the scan button. The transceiver will emit a "di" sound to activate scan. It will stop when a valid signal is scanned. Scan restarts after 5 seconds if the signal disappears.
- Long press the scan button again. The transceiver will emit a "di di" sound to turn off scan.
Power Reporting Function
Through programming software, define PF1/PF2 as the electricity reporting function. Long press the electricity reporting definition key, and the transceiver will emit a "Di" sound and report the current percentage power.
Encryption Function
Encryption Setting (Digital Mode Only)
Based on programming software settings, up to 10 groups can be preset for group encryption or encryption key (10 Byte). Use a pre-programmed key to start/shut down encryption.

Digital encryption protects communication and privacy.
Settings
Setting Squelch Level
Adjust the transceiver squelch level from 1-10. A higher level provides deeper squelch filtration, reducing unwanted calls and background noise. However, calls from remote locations may also be filtered out.
Setting Power Level
You can set each channel's power to High, Middle, or Low. High power is for far-area communication, while middle/low power is for near-area communication. Use the pre-programmed "High / Middle / Low power" selection key.

Optional power settings (1W, 4W, 10W) allow adjustment based on communication needs.
Bluetooth Operations
Bluetooth Switch
Define PF1/PF2 as a Bluetooth switch via programming software (default is PF2). Long press the Bluetooth switch key to turn on Bluetooth (blue light flashes). Long press again to turn off Bluetooth (two "didi" beeps). The blue light stops flashing when connected and flashes when disconnected.
Bluetooth Earphone Operating Instructions

Visual guide for pairing the walkie-talkie with a Bluetooth headset.
- Earphone Power On/Off: Long press for 1 second to turn on, 3 seconds to turn off.
- Volume Control: Use + and - keys.
- PTT Button (Earphone): Short press to transmit/cancel transmission when connected to walkie-talkie. Short press to play/pause, answer/hang up, double-click to make a call when connected to mobile phone.
- Touch PTT (Earphone): Touch to transmit, release to stop.
- Connect New Device: Press and hold power on/off button for 5 seconds to enter pairing mode.
- Clear Connection Memory: Press PTT key 4 times in power-on state to clear Bluetooth connection. Headset will automatically enter pairing mode after rebooting.
- APP Upgrade: Press power on/off button 5 times in power-on state to enter APP upgrade mode.
Earphone Indicator Light Status:
- Power on: Blue light on.
- Bluetooth not connected: Blue light flashes quickly.
- Bluetooth connected: Blue light flashes once every 5 seconds.
- Bluetooth pairing: Red and blue flashing alternately.
- During a call: Red light is always on.
- Low battery: Red light flashes once every 5 seconds.
- Shutdown: Red light flashes 3 times.
- Charging: Red light is always on.
- Fully charged: Red light off.
Steps for Pairing Walkie-Talkie with Bluetooth Headset:
- When the Bluetooth headset is off, press and hold its on/off button for 5 seconds until red and green lights flash alternately (pairing mode).
- Press and hold the PTT key + PF2 key (Bluetooth switch definition key) simultaneously to turn on the walkie-talkie. After the channel number report, a beep will sound, and the blue light will flash quickly (pairing mode).
- After successful pairing, the Bluetooth headset flashes every 5 seconds, and the walkie-talkie's blue light stops flashing.
Troubleshooting
| Symptom | Try This |
|---|---|
| No Power |
|
| Battery lasts a short time after charge | The battery life is over; please replace new battery. |
| Cannot talk to other members of your group |
|
| Hearing other conversation on a channel (not group members) | Please change code settings, including all two-way radio settings of your group. |
| Transceiver continues to tweet | The transceiver channel is empty; please switch to another channel or use it after writing frequency by program software. |
Technical Specifications
| Feature | Specification |
|---|---|
| Model | RT29D (Non-Bluetooth) / RT29D (Bluetooth) |
| Frequency Range | UHF: 400-480MHz |
| Memory Channel | 128 |
| Power | High: 10W, Middle: 4W, Low: 1W |
| Battery Capacity | 3200mAh |
| Voltage | 7.4V |
| Antenna Type | Detachable |
| Antenna Interface | Compatible with SMA-F antenna |
| Audio Jack | Compatible with Motorola multi-pin |
| Contact | 64 |
| RX Group Lists | 32 |
| Dimension | 128*58.5*39mm (Antenna and Channel Knob not Included) |
| Weight | 342g |
| Output Power (W) | 5w-10w |
| Waterproof / Water-Resistant | IP67 |
| Battery Included | Yes |
| Walkie Talkie Type | Portable |
| Is_Display | No |
| Maximum Range | 5km-10km |
| Certification | CE, FCC |
For a complete list of specifications, please refer to the official user manual PDF: User manual (PDF)
Safety and RF Energy Exposure Guide
CAUTION!
Before using this device, please read this guide which contains important operating instructions for safe usage, control information and operational instructions for compliance with RF Energy Exposure limits in applicable national and international standards. User instructions should accompany the device when transferred to other users.
Unauthorized Modification and Adjustment
Changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate this radio. Transmitter adjustments should only be made by or under the supervision of a technically qualified person. Replacement of any transmitter component not authorized by local government radio management departments could violate regulations.
Radio License
Two-way radios operate on authorized radio frequencies regulated by local government radio management departments (e.g., FCC, ISED, OFCOM, ANFR, BFTK, Bundesnetzagentur). Use of this radio outside its intended distribution country is subject to government regulations and may be prohibited. Ensure you have a valid radio license or operator permit before use.
FCC Requirements
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
CE Requirements
Shenzhen Retevis Technology Co., Ltd. declares that the radio equipment type is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU and the ROHS Directive 2011/65/EU and the WEEE Directive 2012/19/EU. The full text of the EU declaration of conformity is available at: www.retevis.com.
Restriction on Putting into Service
This product may be used in various countries and regions. Please refer to the package for the intended country of use.
RF Safety
This two-way radio uses electromagnetic energy. Improper use can cause biological damage. To control your exposure and comply with established RF exposure limits, consider the following:
- Reduce the amount of time spent using your wireless device.
- Use a speakerphone, earpiece, headset, or hands-free accessory to reduce proximity to the head (and thus head exposure).
- Increase the distance between wireless devices and your body.
- Transmit no more than 50% of the time.
Turn Off Your Radio Power in the Following Conditions:
- Before removing or installing accessories.
- Prior to entering any area with a potentially hazardous or explosive atmosphere (e.g., blasting caps, flammable gas, dust particles, fueling areas).
- When taking on fuel or parked at gasoline service stations.
- Do not use any radio with a damaged antenna.
- Do not place a portable radio in the area over an airbag or in the airbag deployment area.
- When on board an aircraft.
Use of Communication Devices While Driving
- Always check laws and regulations on radio use in your driving area.
- Give full attention to driving and the road.
- Use hands-free operation, if available.
- Pull off the road and park before making or answering a call if driving conditions or regulations require.
Protect Your Hearing
- Use the lowest volume necessary.
- Turn up the volume only in noisy surroundings.
- Turn down the volume before adding a headset or earpiece.
- Limit the amount of time you use headsets or earpieces at high volume.
- When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear.
- Be careful with earphones; excessive sound pressure can cause hearing loss.
WARNING: The plug of the adapter is considered a disconnect device. The socket-outlet shall be installed near the equipment and shall be easily accessible.
User Tips
- For optimal range, ensure you are using the highest power setting (10W) when communicating over long distances or through obstacles.
- The IP67 waterproof rating allows the radio to be submerged in 1 meter of water for up to 30 minutes. However, the Bluetooth microphone is not waterproof, so exercise caution when using it in wet conditions.
- Utilize the Bluetooth capability with a headset for hands-free operation, especially in environments where you need to keep your hands free or maintain discretion.
- Take advantage of the Digital & Analog Mode compatibility to communicate with a wider range of two-way radios, reducing the need for multiple devices.
- When using the VOX hands-free function, ensure your Bluetooth headset is properly paired and the function is activated to transmit without pressing the PTT button.
- Regularly check the battery level using the electricity inquiry function to avoid unexpected power loss during critical communications.
- For secure communications, enable the digital encryption feature through the programming software.