Jonsbo N-Series Mini NAS Case (N1, N2, N3, N4, N5)

Contents

JONSBO N-Series Mini NAS Case User Manual

Models: N1, N2, N3, N4, N5

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your JONSBO N-Series Mini NAS Case. Please read this manual thoroughly before beginning assembly to ensure proper setup and optimal performance. The N-Series cases are designed for compact NAS (Network Attached Storage) builds, supporting ITX motherboards and multiple hard drives.

JONSBO NAS Series Small Case N1 N2 N3 N4 Series Overview
Figure 1.1: JONSBO N-Series Mini NAS Cases (N1, N2, N3, N4, N5)

2. Safety Information

Always follow basic safety precautions when assembling or handling computer components to reduce the risk of electric shock, fire, or injury.

  • Disconnect the power cord from the wall outlet before cleaning or performing any maintenance.
  • Do not expose the case to rain or moisture.
  • Do not open the case while the system is powered on.
  • Ensure proper grounding to prevent electrical hazards.
  • Handle components with care to avoid damage from static electricity.

3. Package Contents

Verify that all components listed below are included in your package. Contents may vary slightly by model (N1, N2, N3, N4, N5).

N1 Manual Package Contents and Exploded View
Figure 3.1: N1 Model Package Contents and Exploded View

General Package Contents:

Item Quantity (Approx.) Description
Screws (PSU, MB) 10-18 For Power Supply Unit and Motherboard mounting.
Washers 10-18 For screw insulation and stability.
Screws (SSD) 4-5 For 2.5" SSD installation.
Screws (HDD) 30-72 For 3.5" HDD installation.
HDD Rubber Grommets 20-48 For 3.5" HDD vibration dampening.
Hard Drive Handles 5-8 For easier HDD installation/removal.
Cable Ties (Velcro) 1-5 For cable management.
Screw Wrench 1 Tool for loosening/tightening screws.
Iron Columns 16 For motherboard mounting (N4).
HEX Wrench Socket 1 For hexagonal iron column installation (N4).
Fan Screws 12 For fan installation.
Spare Screws 2 Extra screws.
Bottom Cover Filter 1 Dust filter for the bottom panel.
Top Cover Filter 2 Dust filter for the top panel.

4. Specifications

The JONSBO N-Series cases offer various configurations. Please refer to the specific model's specifications below.

N5 Product Specification Diagram
Figure 4.1: N5 Model Product Specification Diagram

General Specifications:

Feature Description
Form Factor ITX (N1, N2, N3, N5), ITX/M-ATX (N4)
Material Aluminum alloy, Steel (some models include wood panels)
Power Model SFX (N1, N2, N3, N4), ATX (N5)
RGB Support Fixed Color (if applicable)
With Fan Yes (standard configuration varies by model)

Model-Specific Specifications:

Feature N1 N2 N3 N4 N5
Product Size (W*D*H) 170mm*354mm*217mm 222.5mm*222.5mm*224mm 233mm*262mm*298mm 286mm*300mm*228mm 355mm*403mm*350mm
Weight 3.8kg 2.9kg 3.9kg 3.75kg 7.5kg
Hard Disk Space 2.5"SSD*1/3.5"HDD*5 2.5"SSD*1/3.5"HDD*5 2.5"SSD*1/3.5"HDD*8 2.5"SSD*2/3.5"HDD*6 2.5"SSD*2 or 4/3.5"HDD*12
PCI Expansion Slots 1 (half-height) 1 (half-height) 2 4 8
Max CPU Cooler Height ≤70mm ≤65mm ≤130mm ≤70mm ≤160mm
Max GPU Length ≤185mm (single slot half-height) ≤197mm (single slot half-height) ≤250mm ≤230mm ≤325mm or ≤350mm
Max PSU Length SFX≤150mm SFX≤150mm SFX≤105mm SFX≤125mm ATX≤170mm-240mm
Front Ports Type-C(20PIN)/USB3.0*1/AUDIO*1+MIC*1(2-in-1) 1*USB3.0/1*USB3.2 Gen2 Type-c/Audio+Mic (2-in-1) 1*USB3.0/1*USB3.2 Gen2 Type-C/Audio+Mic (2-in-1) Type-C*1 / USB3.0*1 USB3.2 Gen2 Type-C*1 / USB3.0*1 / AUDIO*1 (Headset+mic combined)

5. Setup and Installation

This section outlines the general steps for assembling your JONSBO N-Series NAS case. Specific details and diagrams may vary slightly between models. A comprehensive user manual (PDF) is available for download here.

5.1. Remove the Case Cover

Before installing any hardware, the case cover must be removed. For most models, this involves loosening screws on the top plate and sliding the top cover back.

N5 Remove Case Cover Instruction
Figure 5.1: Removing the case cover (N5 model shown)
  1. Use the provided screw wrench to loosen the screws on the top cover.
  2. Slide the top cover backward to remove it.
  3. Remove the PSU bracket and fan bracket if necessary for easier access.

5.2. Motherboard Installation

Install the ITX motherboard into the case, ensuring proper alignment with the standoffs.

N5 Motherboard Installation Diagram
Figure 5.2: Motherboard installation (N5 model shown)
  1. For N4 models, first install the hexagonal iron columns using a screwdriver and socket into the corresponding motherboard mounting holes.
  2. Place the motherboard into the designated area, aligning it with the standoffs.
  3. Secure the motherboard with screws.

5.3. Power Supply Unit (PSU) Installation

Install the SFX (or ATX for N5) power supply into its designated rack.

N5 Power Supply Installation Diagram
Figure 5.3: Power supply installation (N5 model shown)
  1. Install the PSU onto the power supply rack.
  2. Place the installed PSU into the chassis and secure it with screws.

5.4. Cable Management

Before installing other components, organize the power cables to ensure proper airflow and ease of installation.

N5 Cable Management Diagram
Figure 5.4: Cable management (N5 model shown)
  • Route hard drive data cables (SATA) through designated areas.
  • Organize PCB board power cables through wiring holes.
  • Route CPU power cables to their respective connectors.
  • Use provided cable ties to secure cables.

5.5. Hard Drive (HDD/SSD) Installation

Install your 2.5" SSDs and 3.5" HDDs into their respective bays.

N5 3.5 HDD Installation Diagram
Figure 5.5: 3.5" HDD installation (N5 model shown)
  1. For 3.5" HDDs, pre-install the rubber grommets and hard drive handles onto the HDD using screws.
  2. Insert the assembled HDD into the corresponding slots/bays.
  3. For 2.5" SSDs, install them into the corresponding brackets and secure with screws.
  4. For models with an active hard drive cage (e.g., N5), pull the front panel strap outwards to open the front panel, then remove the screws from the movable hard drive cage to access the bays.

5.6. Fan and Graphics Card Installation

Install any additional fans and your graphics card (if applicable).

N5 Graphics Card Installation Diagram
Figure 5.6: Graphics card installation (N5 model shown)
  1. Remove the PCI-E card strip and PCI-E cover from the case.
  2. Insert the graphics card into the motherboard's PCI-E slot and secure it with screws.
  3. Install front panel or side fans into their respective brackets and secure them. For front panel fans, you may need to remove mounting screws first.

5.7. Top Cover and Filters Installation

After all hardware is installed, reattach the top cover and install any filters.

N5 Top Cover Installation Diagram
Figure 5.7: Top cover installation (N5 model shown)
  1. Install the top cover and fan bracket.
  2. Install the bottom cover filter and top cover filters by adhering them to the ventilation holes.
  3. For models with vertical case stands, install the stand to the rear panel.

6. Operating Instructions

Once assembly is complete and all components are securely installed, connect your peripherals and power cable.

6.1. Front Panel Connectors

The front panel provides convenient access to USB ports and audio jacks.

N2 Front Panel Connectors Diagram
Figure 6.1: Front panel connectors (N2 model shown)
  • USB 3.0 Port: Connect USB 3.0 devices for high-speed data transfer.
  • USB 3.2 Gen2 Type-C Port: Connect compatible Type-C devices.
  • Audio + Mic (2-in-1) Jack: Connect headphones or a headset.
  • Power Button: Press to power on/off the system.
  • Power LED: Indicates system power status.
  • HDD LED: Indicates hard drive activity.

6.2. Power On/Off

  • To Power On: Press the power button located on the front panel.
  • To Power Off: Press the power button briefly for a soft shutdown (if configured in OS) or press and hold for 5 seconds for a forced shutdown.

7. Maintenance

7.1. Cleaning

  • Ensure the system is powered off and unplugged before cleaning.
  • Use a soft, dry cloth to wipe down the exterior of the case.
  • For stubborn dirt, a slightly damp cloth can be used, followed by a dry cloth.
  • Avoid using harsh chemicals or abrasive cleaners.

7.2. Filter Maintenance

Regularly clean the dust filters to maintain optimal airflow and cooling performance.

N5 Top Cover Filter Installation Diagram
Figure 7.1: Top cover filter installation (N5 model shown)
  1. Locate the bottom and top cover filters.
  2. Gently tear off the filter film from the cover.
  3. Clean the filters with compressed air or rinse with water (ensure they are completely dry before re-installation).
  4. Re-adhere the filters to the ventilation holes.

8. Troubleshooting

If you encounter issues, refer to the following common problems and solutions.

  • System does not power on:
    • Check if the power cable is securely connected to both the PSU and the wall outlet.
    • Ensure the PSU switch is in the 'ON' position.
    • Verify that the front panel power button cable is correctly connected to the motherboard.
  • No display output:
    • Ensure the graphics card (if installed) is properly seated in its PCI-E slot and power cables are connected.
    • Check the display cable connection to both the graphics card/motherboard and the monitor.
  • Hard drives not detected:
    • Verify that SATA data and power cables are securely connected to both the hard drives and the motherboard/PSU.
    • Check BIOS/UEFI settings to ensure SATA ports are enabled.
  • Poor cooling performance/Overheating:
    • Ensure all case fans are properly installed and connected.
    • Clean dust filters regularly to maintain airflow.
    • Verify CPU cooler is correctly installed and making good contact with the CPU.

9. User Tips

  • HDD Mounting: The cases come with numerous HDD mounting parts, making them suitable for NAS builds requiring many drives. Be aware that mounting HDDs in the front bay might involve screwing in plastic handles, which some users find a bit cumbersome.
  • Power Supply: These cases typically require an SFX power supply (N5 uses ATX). SFX PSUs can be a specialized component, so plan accordingly for availability and cost.
  • Documentation: The included documentation is generally considered reasonable and helpful for assembly.
  • Compatibility: Users have successfully paired these cases with various NAS motherboards (e.g., Topton 10G NAS motherboards) and multiple SSDs.
  • Hot-Swap: Note that hot-swap functionality might be limited (e.g., only for 4 drives on some models like N3).

10. Warranty and Support

JONSBO Technology Co., Ltd. products are manufactured under strict quality control. For warranty information and technical support, please refer to the official JONSBO website or contact your local distributor. Keep your proof of purchase for warranty claims.

Contact Information:
Dongguan Sibositong Industrial Co., Ltd.
No.5, Xinglong Lu, Sanzhong Village, Qingxi Town, Dongguan City, Guangdong Province, 523651, China

Specifications are subject to change without prior notice. Some trademarks may be claimed as the property of others.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.