1. Product Overview
The LEDING Digital Wall Clock (Model JH120) is a versatile device featuring a large LED display for time, stopwatch, and countdown functions. Its sturdy and compact design makes it suitable for various indoor environments. The clock comes with a remote control for convenient operation and is powered via a USB cable and bivolt adapter.
Figure 1: LEDING Digital Wall Clock JH120 and Remote Control
Video 1: Unboxing and basic function demonstration of the Digital Wall Clock.
2. Package Contents
Please check the box for the following items:
- 1 x LEDING Digital Wall Clock (Stopwatch)
- 1 x Bivolt Cable Source (Power Adapter)
- 1 x Remote Control
- 1 x USB Cable
- 1 x Instruction Manual (this document)
Figure 2: All components included in the package.
3. Setup
- **Unpack**: Carefully remove all components from the packaging.
- **Connect Power**: Connect the USB cable to the clock and then plug the bivolt power adapter into a standard electrical outlet (110V or 220V). The clock will power on automatically.
- **Remote Control**: Ensure the remote control has batteries installed (if not already pre-installed). The remote is essential for setting up and operating the clock's various functions.
Figure 3: Remote control, USB cable, and power adapter details.
4. Operating Instructions
The clock can be operated using the included remote control. Familiarize yourself with the remote's buttons:
- **Power Button**: Turns the display on/off.
- **12/24**: Toggles between 12-hour and 24-hour time format.
- **SET**: Enters setting mode for time, alarm, or timer.
- **OK**: Confirms selection in setting mode.
- **EXIT**: Exits setting mode.
- **Up/Down Arrows**: Adjust values during setting.
- **Left/Right Arrows**: Move between digits or settings.
- **AL**: Accesses alarm settings.
- **STOPWATCH**: Activates stopwatch mode.
- **COUNTUP**: Activates progressive stopwatch mode.
- **COUNTDOWN**: Activates countdown timer mode.
- **Number Buttons (0-9)**: Used for direct input of time or timer values.
4.1 Setting the Time
- Press the **SET** button on the remote. The hour digits will start flashing.
- Use the **Up/Down** arrows to adjust the hour.
- Press the **Right Arrow** to move to the minute digits, then use **Up/Down** to adjust.
- Repeat for seconds if applicable.
- Press **OK** to confirm and save the time.
- Use the **12/24** button to switch between 12-hour and 24-hour display formats.
4.2 Using the Stopwatch (Progressive)
- Press the **STOPWATCH** or **COUNTUP** button. The display will show 00:00:00.
- Press **OK** to start the stopwatch.
- Press **OK** again to pause.
- Press **EXIT** to reset the stopwatch to 00:00:00.
4.3 Using the Countdown Timer (Regressive)
- Press the **COUNTDOWN** button. The display will show a default countdown time or the last set time.
- Press **SET**. The digits will flash.
- Use the **Number Buttons (0-9)** or **Up/Down/Left/Right** arrows to set your desired countdown time (e.g., 00:05:00 for 5 minutes).
- Press **OK** to confirm the time.
- Press **OK** again to start the countdown.
- When the countdown reaches 00:00:00, an alarm will sound.
- Press **EXIT** to stop the alarm and reset the timer.
4.4 Setting an Alarm
- Press the **AL** button. The alarm time will be displayed, and the hour digits will flash.
- Use the **Up/Down** arrows to set the desired alarm hour.
- Press the **Right Arrow** to move to the minute digits, then use **Up/Down** to set the minutes.
- Press **OK** to confirm the alarm time.
- To activate/deactivate the alarm, press the **AL** button again briefly. An indicator (e.g., a small dot or icon) on the display will show if the alarm is active.
5. Maintenance
- **Cleaning**: Use a soft, dry cloth to clean the display and casing. Do not use abrasive cleaners or solvents.
- **Power**: Always use the provided power adapter and USB cable.
- **Environment**: Keep the clock in a dry environment, away from direct sunlight and extreme temperatures.
- **Memory Retention**: The quartz electronic system is designed to retain time settings even after power loss.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Clock display is off. | No power or power button pressed. | Check power connection. Press the power button on the remote. |
| Remote control not responding. | Remote batteries low or line of sight blocked. | Replace remote batteries. Ensure clear line of sight to the clock's sensor. |
| Time/Timer not setting correctly. | Incorrect button sequence. | Refer to the 'Operating Instructions' section for correct steps. |
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | JH120 |
| Origin | Mainland China |
| Power Input | Bivolt (110V or 220V automatic) |
| Display Color | Red LED |
| Time Format | hh:mm:ss (12/24 hour options) |
| Functions | Clock, Progressive Stopwatch, Countdown Timer, Alarm |
| Regressive Stopwatch Range | 99:59:59 to 00:00:00 |
| Progressive Stopwatch Range | 00:00:00 to 99:59:59 |
| Number Size | 5.5cm x 3cm |
| Dimensions | 32cm (Length) x 9cm (Height) x 4cm (Depth) |
| Weight | 340g |
8. User Tips
- For optimal visibility, place the clock in a location with good line of sight, as the LED display offers long-range viewing.
- Keep the remote control handy for quick adjustments to time, timers, and alarms.
- The clock's memory retention feature ensures your settings are saved even if power is temporarily interrupted.
- Experiment with both the progressive and regressive stopwatch functions to find the best use for your needs, whether for workouts, cooking, or study sessions.
9. Warranty and Support
For any questions, technical support, or warranty claims regarding your LEDING Digital Wall Clock JH120, please contact the seller or retailer from whom you purchased the product. Please retain your proof of purchase for warranty purposes.