Dooya DM25LEU

Contents

DOOYA DM25LEU Tubular Motor Instruction Manual

For Electric Roller Blinds with RF433 Emitter Control

1. Introduction

Thank you for choosing the DOOYA DM25LEU Tubular Motor. This motor is designed for electric roller blinds and features a built-in lithium battery with USB charging and RF433 emitter control. Please read this manual carefully before installation and operation to ensure proper use and longevity of your product.

DOOYA DM25LEU Tubular Motor and Remote Control

Figure 1: DOOYA DM25LEU Tubular Motor and Remote Control

Video 1: Unboxing and overview of the DOOYA DM25LEU Tubular Motor.

2. Safety Information

  • Ensure the motor is installed by a qualified professional if you are unsure about the process.
  • Do not expose the motor to water or extreme temperatures.
  • Keep the remote control out of reach of children.
  • Do not attempt to open or repair the motor yourself. Contact support for assistance.
  • Always disconnect power before performing any maintenance or cleaning.

3. Product Specifications

The DOOYA DM25LEU Tubular Motor is designed for use with 38mm diameter tubes, commonly found in roller blinds.

Motor tube compatibility diagram

Figure 2: The DM25LEU motor is compatible with 38mm diameter tubes.

AttributeValue
Model NumberDM25LEU
Brand NameDooya
TypeElectric Tubular Motor Roller Blind Drive
VoltageDC 5V / 2A
Wattage10W
Rolling Speed20rpm
Torque (N.m)1.1Nm
Motor SizeDiameter 25mm
Power SupplyBuilt-in rechargeable battery (2200mAh)
Control ModeRemote control (RF433)
Frequency433.92MHz
Opening and Closing MethodUpper Open
Used ForRoller Blinds
CertificationCE
IP RatingIP44
Motor specification label

Figure 3: Detailed motor specification label.

Product package dimensions

Figure 4: Product package dimensions (52cm x 11cm x 6cm).

4. Setup and Installation

The DM25LEU motor is designed to fit into a 38mm diameter tube. The tube itself is not included in the package. Installation typically involves:

  1. Inserting the motor into the roller blind tube.
  2. Securing the motor and tube assembly using appropriate brackets (included with some kits, or purchased separately).
  3. Connecting the motor to a power source for initial charging.
Motor and USB cable, showing Li battery power and 38mm tube compatibility

Figure 5: DM25LEU motor with USB cable, highlighting Li battery power and 38mm tube compatibility.

5. Operation

The motor is controlled via an RF433 emitter (remote control). The DOOYA DC2700 single-channel remote is a common compatible option.

DOOYA DC2700 Single Channel Emitter remote control

Figure 6: DOOYA DC2700 Single Channel Emitter remote control.

The following instructions detail the control system functions:

Control System Instructions for DOOYA DM25LEU Tubular Motor

Figure 7: Comprehensive diagram detailing the motor's control system.

5.1. Dot-Move Setting

This function allows for precise, incremental movement of the blind.

  1. **Power on** the motor.
  2. Press the **Up** button on the remote. The motor will beep once.
  3. Press the **Up** button again. The motor will beep twice.
  4. Press the **Up** button a third time. The motor will beep three times.
  5. The dot-move setting is now active.

5.2. Add Emitter (Remote Control)

To pair a new remote control with the motor:

  1. **Power on** the motor.
  2. Press the **P2** button on an already paired emitter (remote). The motor will beep once.
  3. Press the **P2** button on the same emitter again. The motor will beep twice.
  4. Press the **P2** button on the new emitter you wish to add. The motor will beep once.
  5. The new emitter is now added.

5.3. Delete Emitter (Remote Control)

To remove a paired remote control from the motor:

  1. **Power on** the motor.
  2. Press the **P2** button on the emitter you wish to delete. The motor will beep once.
  3. Press the **P2** button on the same emitter again. The motor will beep twice.
  4. Press the **P2** button on the same emitter a third time. The motor will beep three times.
  5. The emitter is now deleted.

5.4. Delete Limit Settings

To clear the upper and lower limit settings of the motor:

  1. **Power on** the motor.
  2. Press the **Stop** button on the remote. The motor will beep once.
  3. Press the **Stop** button again. The motor will beep twice.
  4. Press the **Stop** button a third time. The motor will beep three times.
  5. The limit settings are now deleted.

5.5. Matchable Emitters

The DM25LEU motor is compatible with various DOOYA RF433 emitters, including:

  • DC161A Single-channel emitter
  • DC1600 Single-channel emitter
  • DC2700 Single-channel emitter
  • DC1612 15-channel emitter
  • DC1602 15-channel emitter
  • DC1602 15-channel LCD emitter

5.6. Button Specification (Setting Limits)

The motor features an E-Electronic / Electronic Built-in receiver and setting buttons for configuring upper and lower limits. These buttons are typically located on the motor itself, often under a cover or accessible via a small hole (refer to Figure 7 for visual guidance).

  • **Up Button**: Moves the blind upwards.
  • **Stop Button**: Stops the blind movement.
  • **Down Button**: Moves the blind downwards.
  • **Setting Button**: Used to confirm limit positions.

To set the upper and lower limits, follow the specific instructions provided with your remote control or refer to the detailed diagram in Figure 7. Generally, this involves moving the blind to the desired upper/lower position and then pressing a combination of buttons on the remote and/or the motor's setting button to save the position.

6. Charging and Maintenance

The DM25LEU motor is equipped with a built-in lithium battery that requires charging.

  • **Initial Charge**: When using the DM25LEU motor for the first time, please charge it for at least 10 hours.
  • **Regular Charging**: To maintain battery health, charge the motor every 3 months, even if not in active use.
  • **Low Voltage Alarm**: Do not operate the motor when it indicates a low voltage alarm. Charge it promptly.
USB charging port and cable for the motor

Figure 8: USB charging port and cable.

Close-up of motor end cap showing USB charging port and Reset Key

Figure 9: Motor end cap with USB charging port and Reset Key.

6.1. Reset Key

The motor includes a 'Reset Key' (refer to Figure 9) which can be used to reset certain settings or troubleshoot issues. Consult the detailed control system diagram (Figure 7) or your remote's specific instructions for its usage in various scenarios.

7. Troubleshooting

If you encounter issues with your DM25LEU motor, consider the following:

  • **Motor not responding**: Check if the battery is charged. Ensure the remote control has fresh batteries and is properly paired.
  • **Limits not setting correctly**: Refer to the 'Delete Limit Settings' and 'Button Specification' sections (5.4 and 5.6) to reconfigure the limits.
  • **Intermittent control**: Ensure there are no obstructions blocking the RF signal between the remote and the motor. Check for potential interference from other 433MHz devices.
  • **Motor operating slowly or weakly**: This could indicate a low battery. Charge the motor for the recommended duration.

If problems persist after following these steps, please contact customer support.

8. User Tips

  • For optimal battery life, perform the initial 10-hour charge and subsequent quarterly charges as recommended.
  • Keep your remote control in a consistent location to avoid misplacing it.
  • Consider the application environment; the motor is rated IP44, meaning it is protected against solid objects over 1mm and splashing water from any direction, but not full immersion.
  • When installing, ensure the motor is securely fitted within the 38mm tube to prevent slippage and ensure smooth operation.

9. Warranty and Support

9.1. Warranty

This product comes with a 1-year Manufacturer's Warranty for defective items. This warranty does not cover items damaged or misused after receipt. All products are checked, tested, and packed in good condition before delivery. Defective items must be reported and returned within the warranty period, along with the original packaging. Please provide details of the defect to help eliminate improper use.

9.2. Customer Service

We strive for 100% customer satisfaction. If you have any concerns or issues, please contact us immediately before leaving neutral or negative feedback. We will do our best to resolve the problem. Your 5-star feedback is greatly appreciated.

Customer service and support image

Figure 10: Customer service and support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.