LILYGO T-SIM7070G

Contents

LILYGO TTGO T-SIM7070G ESP32 SIM Development Board User Manual

Model: T-SIM7070G

1. Introduction

The LILYGO TTGO T-SIM7070G is an ESP32-based development board designed for IoT applications requiring LPWA (Low-Power Wide-Area) communication. It integrates the SIM7070G module, supporting Cat-M, Cat-NB, GPRS, and EDGE networks, alongside ESP32's built-in Wi-Fi and Bluetooth capabilities. This open-source board is ideal for developers and makers looking to create projects with robust wireless connectivity and low power consumption.

2. Safety Information

  • Always handle the development board with care to avoid electrostatic discharge.
  • Ensure correct power supply voltage (recommended 4.4V to 6V for solar panels, do not exceed to prevent damage).
  • Do not short-circuit pins or components.
  • Keep the board away from moisture and extreme temperatures.
  • Disconnect power before making any physical connections or modifications.

3. Package Contents

The T-SIM7070G version package typically includes the following items:

  • 1x LILYGO T-SIM7070G module
  • 1x LTE antenna
  • 1x GPS antenna
  • 1x Power cable
  • 2x Pin headers
LILYGO T-SIM7070G module and included accessories
LILYGO T-SIM7070G module with included LTE antenna, GPS antenna, power cable, and pin headers.

4. Product Overview

The LILYGO T-SIM7070G board features an ESP32 microcontroller for Wi-Fi and Bluetooth connectivity, combined with a SIM7070G module for cellular communication (Cat-M/Cat-NB/GPRS/EDGE) and GNSS capabilities. It includes a TF card slot, a Nano SIM card slot, and a holder for an 18650 battery, making it suitable for portable and low-power applications.

Front and back view of the LILYGO T-SIM7070G development board
Front and back view of the LILYGO T-SIM7070G development board.
LILYGO T-SIM7070G pinout diagram
Detailed pinout diagram for the LILYGO T-SIM7070G board, showing GPIOs, power, and communication interfaces.

5. Setup

5.1 Initial Notes for New Users

  • The SIM7070G module does not support 4G networks. Ensure your USIM card supports 2G (GSM) or NB-IoT access.
  • SIM7070G positioning (GPS) and cellular communication cannot be used simultaneously. Disconnect the network when using GPS, and turn off GPS when connecting to the network.
  • The VIN pin is for USB input. If powering the device via battery, there will be no voltage output from VIN; 3.3V is the only power output.
  • When using the built-in battery pack, the on/off switch controls power. If an external battery pack is connected to the VBAT pin, the on/off switch is bypassed, and batteries must be disconnected to power off.
  • The on/off switch functions only for battery use and will not work when the board is plugged into USB.
  • Battery voltage cannot be read via the onboard BAT ADC (GPIO35) when the board is plugged into USB.
  • Recommended solar panel input is 4.4V to 6V. Exceeding this voltage may damage the board.
  • When an SD card is inserted, you cannot upload software using the Arduino IDE because the SD card uses IO2 as CS. The SD card must be removed before uploading a new sketch.
  • For Version 20200415, when using GPS, GPIO5 (physical pin 48) on the SIM7070G needs to be set to HIGH to enable the antenna using modem.sendAT("+CGPIO=0,48,1,1");. After use, set it LOW with modem.sendAT("+CGPIO=0,48,1,0"); to prevent power leakage and conserve battery life. If using USB or if battery life is not a concern, it can be left HIGH.

5.2 Software Setup

For code examples, libraries, and further development resources, please refer to the official LILYGO GitHub repository:

Firmware updates can be performed using the Espressif Flash Download Tools. You can find the tool and upgrade guidelines at:

6. Operating Instructions

6.1 Network Connection

The initial network registration process may take some time. Please be patient during this phase.

To change the connection method (e.g., between different network modes), you can modify the `modem.setNetworkMode()` function in your Arduino sketch. For example, in `Arduino_TinyGSM/AllFunctions.ino`, change `modem.setNetworkMode(38);` to the corresponding mode number. The network access speed will depend on your SIM card carrier and the selected mode. It is advisable to consult your SIM card operator for supported modes and bands.

Arduino IDE code for network mode settings
Example Arduino IDE code snippet for setting network mode and preferred mode.

You can also configure locked bands to optimize network performance. An example of this configuration is shown below:

Arduino IDE code for configuring locked bands
Example Arduino IDE code snippet for configuring specific network bands using AT commands.

6.2 GPS Usage

As noted in the setup section, GPS positioning and cellular communication cannot be active simultaneously. Ensure cellular network is disconnected when using GPS. For battery-powered applications, remember to manage the GPS antenna power via GPIO5 (physical pin 48) to conserve energy.

7. User Tips

  • To avoid conflicts, always remove the SD card from the slot before uploading new code to the board via the Arduino IDE.
  • When using GPS on battery power, remember to toggle the GPS antenna power (GPIO5) to HIGH only when needed and LOW when not in use to extend battery life.
  • If you encounter network access issues, try running the `examples/Arduino_NetworkTest` sketch from the GitHub repository to diagnose the connection.
  • For optimal performance, ensure your USIM card is compatible with 2G (GSM) or NB-IoT networks, as the SIM7070G does not support 4G.

8. Specifications

FeatureT-SIM7070G
MCUESP32
LTE & GSM ModuleSIM7070G
SIM Card SupportNano SIM (2G/NB-IoT)
TF Card SupportYes
ESP32 Clock Speed240MHz
Flash4MB
PSRAM4MB
Wireless ConnectivityWi-Fi: 802.11 b/g/n, Bluetooth: v4.2 BR/EDR and BLE
Peripheral InterfacesI2C, SPI, UART, SDIO, I2S, CAN
Form FactorLCC, 68PIN
RegionGlobal
Dimensions24*24*2.6 (mm)
Serial ChipCH9102F
GSM Frequency Bands850/900/1800/1900MHz
Cat-M1 Frequency BandsB1/B2/B3/B4/B5/B8/B12/B13/B17/B18/B19/B20/B25/B26/B28/B39/B66/B85
Cat-NB1/NB2 Frequency BandsB1/B2/B3/B5/B8/B12/B13/B17/B18/B19/B20/B25/B26/B28/B66/B71/B85
Power Consumption (PSM)3.2 uA
Power Consumption (Sleep)0.8 mA
Power Consumption (Idle)10 mA
Data Transfer (Cat-M)589(DL)/1119(UL) Kbps
Data Transfer (Cat-NB)127(DL)/158.5(UL) Kbps
Data Transfer (EGPRS)296(DL)/236.8(UL) Kbps
GNSSBeidou, GPS, GLONASS
ProtocolsTCP/UDP/HTTP/HTTPS/FTP/TLS/DTLS/PING/LWM2M/COAP/MQTT
Software FeaturesFOTA, Embedded AT, Firmware Upgrade
Supply Voltage3.2V ~ 4.2V
CertificationRoHS/REACH/CCC/CE(RED)/GCF/Deutsche Telekom/FCC/IC/OCD(Anatel)
LILYGO T-SIM7070G detailed specifications table
Detailed specifications for the LILYGO T-SIM7070G development board.
LILYGO T-SIM7070G frequency band comparison
Frequency band support for GSM, Cat-M1, Cat-NB1, Cat-NB2, and GNSS on the T-SIM7070G.
LILYGO T-SIM7070G power consumption and data transfer rates
Power consumption, data transfer rates, and supported protocols for the T-SIM7070G.

9. Troubleshooting

  • Network Connection Issues: If you are unable to access the network, try running the `examples/Arduino_NetworkTest` sketch from the official GitHub repository. This sketch is designed to test network connectivity.
  • Slow Network Registration: The initial network registration may be slow. Please allow sufficient time for the module to connect.
  • Software Upload Failure: Ensure that the SD card is removed from the slot before attempting to upload new software to the board via the Arduino IDE. The SD card uses IO2, which can interfere with the upload process.
  • GPS/Cellular Conflict: Remember that SIM7070G positioning and cellular functions cannot be used simultaneously. Ensure one is disabled when the other is in use.

10. Warranty and Support

LILYGO is committed to providing quality products and support for the maker community. As an open-source project, we encourage users to engage with the community and share their experiences.

10.1 Customer Service

For any questions or concerns regarding your LILYGO product, please contact customer service. We are dedicated to providing satisfactory solutions.

  • If you have any unclear questions about the product, please do not hesitate to contact us for assistance.
  • In case of package damage due to external force or transportation, please provide clear pictures of the logistics label, packaging, and the damaged product. We will work with the logistics service provider to offer a solution.
  • For inquiries about product customization, bulk purchases, or any other product-related questions, feel free to reach out to our customer service team.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.