Fubag FES1814C

Contents

Electric Motor for Fubag FES1814C

Model: SF7J153-1600 / SF7J153 220V

Introduction

This manual provides essential information for the installation, operation, maintenance, and troubleshooting of the electric motor components designed for the Fubag FES1814C power tool. It covers the rotor, stator, and carbon brushes, which are critical parts for the motor's function. Please read these instructions carefully before attempting any installation or maintenance.

Product Components and Specifications

The electric motor assembly for the Fubag FES1814C consists of several key components, each with specific dimensions and characteristics.

Rotor (Armature)

Rotor component with SF7J153 220V marking
Figure 1: Rotor component with SF7J153 220V marking.

The rotor is the rotating part of the electric motor, responsible for generating mechanical power. It features copper windings and a commutator.

Measurement of the rotor's core diameter, showing 38.84 mm
Figure 2: Measurement of the rotor's core diameter.

Rotor Specifications:

  • Model Marking: SF7J153 220V
  • Core Diameter: Approximately 38.84 mm

Stator

Stator component with copper windings
Figure 3: Stator component with copper windings.

The stator is the stationary part of the motor, containing field windings that create a magnetic field to interact with the rotor.

Measurement of the stator's core diameter, showing 37.97 mm
Figure 4: Measurement of the stator's core diameter.

Stator Specifications:

  • Core Diameter: Approximately 37.97 mm

Carbon Brushes

Individual carbon brush with spring mechanism
Figure 5: Individual carbon brush with spring mechanism.

Carbon brushes conduct electricity between the stationary wires and the rotating commutator of the motor. They are consumable parts that require periodic inspection and replacement.

Measurement of a carbon brush's length, showing 10.92 mm
Figure 6: Measurement of a carbon brush's length.
Measurement of a carbon brush's width, showing 5.92 mm
Figure 7: Measurement of a carbon brush's width.

Carbon Brush Specifications:

  • Length: Approximately 10.92 mm
  • Width: Approximately 5.92 mm
  • SKU Property: 1 PCs brush (5.9x10.9)

Installation and Setup

These components are replacement parts for the Fubag FES1814C electric motor. Proper installation is crucial for safe and efficient operation. Always ensure the power tool is disconnected from the power source before beginning any installation or repair work.

  1. Safety First: Disconnect the power tool from the main power supply.
  2. Access Motor Housing: Carefully open the housing of your Fubag FES1814C to access the motor assembly. Refer to your tool's original service manual for specific disassembly instructions.
  3. Component Replacement:
    • Rotor/Stator: If replacing the rotor or stator, carefully remove the old component, noting its orientation and connections. Install the new rotor/stator, ensuring all electrical connections are secure and correctly wired.
    • Carbon Brushes: Locate the brush holders. Remove the old carbon brushes and insert the new ones, ensuring the spring mechanism provides adequate contact pressure.
  4. Reassembly: Once new components are installed, carefully reassemble the motor housing, ensuring all screws are tightened and no wires are pinched.
  5. Test: Before full use, perform a brief test run to ensure the motor operates smoothly without unusual noises or sparks.

Warning: Electrical work should only be performed by qualified individuals. Improper installation can lead to electric shock, fire, or damage to the tool.

Operating Principles

This electric motor is designed to power the Fubag FES1814C tool. Once correctly installed and the tool is reassembled, operate the tool according to its original manufacturer's instructions. The motor converts electrical energy into mechanical energy, driving the tool's function.

  • Ensure the tool is connected to a power supply matching the motor's voltage (220V as indicated on the rotor).
  • Avoid overloading the tool, as this can strain the motor and lead to premature wear or failure.
  • Listen for unusual noises during operation, which may indicate a problem with the motor or other tool components.

Maintenance

Regular maintenance extends the life of your electric motor and ensures optimal performance. The primary maintenance task for this type of motor involves the carbon brushes.

  1. Carbon Brush Inspection: Periodically inspect the carbon brushes for wear. Worn brushes can cause intermittent operation, reduced power, or excessive sparking. The frequency of inspection depends on tool usage.
  2. Carbon Brush Replacement:
    • When brushes wear down to approximately 1/4 of their original length, they should be replaced.
    • Always replace both carbon brushes at the same time to ensure even wear and consistent performance.
    • Use only genuine replacement brushes or those with identical specifications (e.g., 5.9x10.9 mm).
    • Ensure the new brushes slide freely in their holders and make good contact with the commutator.
  3. Commutator Cleaning: If excessive sparking is observed, the commutator on the rotor may need cleaning. This should be done carefully with a non-abrasive material. If the commutator is heavily grooved or pitted, the rotor may need replacement.
  4. General Cleanliness: Keep the motor housing and ventilation openings clean to prevent dust and debris from accumulating, which can lead to overheating.

Troubleshooting

ProblemPossible CauseSolution
Motor does not start or runs intermittently.
  • Worn or stuck carbon brushes.
  • Loose electrical connections.
  • Power supply issue.
  • Damaged rotor or stator windings.
  • Inspect and replace carbon brushes.
  • Check all wiring connections.
  • Verify power supply to the tool.
  • Inspect rotor and stator for visible damage; replace if necessary.
Excessive sparking at the commutator.
  • Worn or improperly seated carbon brushes.
  • Dirty or damaged commutator.
  • Overload condition.
  • Replace carbon brushes.
  • Clean commutator or replace rotor if severely damaged.
  • Reduce load on the tool.
Reduced power or unusual noise.
  • Worn carbon brushes.
  • Bearing wear (not part of this product, but common motor issue).
  • Partial winding failure in rotor or stator.
  • Inspect and replace carbon brushes.
  • Consult a qualified technician for bearing or winding issues.
Motor overheating.
  • Blocked ventilation.
  • Continuous heavy load.
  • Internal electrical fault.
  • Clean ventilation openings.
  • Allow tool to cool; avoid prolonged heavy use.
  • Seek professional diagnosis for internal faults.

User Tips

  • When replacing components, take photos of the original setup to aid in reassembly.
  • Always use appropriate personal protective equipment (PPE) when working with power tools and electrical components.
  • Keep spare carbon brushes on hand, as they are common wear items.

Warranty and Support

For warranty information regarding the Fubag FES1814C power tool or these replacement motor components, please refer to the original product documentation or contact the manufacturer directly. For technical support, it is recommended to consult with a certified Fubag service center or a qualified power tool repair technician.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.