EOENKK 18650 lithium battery pure nickel sheet

Contents

18650 Lithium Battery Pure Nickel Sheet Instruction Manual

Model: 18650 Lithium Battery Pure Nickel Sheet

Brand: EOENKK

1. Introduction

This manual provides essential information for the safe and effective use of the EOENKK 18650 Lithium Battery Pure Nickel Sheet. This product is designed for connecting 18650 lithium battery cells, primarily for spot welding applications in battery pack assembly. Please read this manual thoroughly before use to ensure proper handling and to prevent potential hazards.

2. Safety Information

WARNING: Working with lithium batteries and spot welding equipment can be dangerous if proper precautions are not followed. Always prioritize safety.

  • Always wear appropriate personal protective equipment (PPE), including safety glasses and gloves.
  • Ensure adequate ventilation when working with batteries and welding equipment.
  • Never short-circuit battery cells or nickel strips.
  • Use only compatible and properly functioning spot welding equipment.
  • Keep a fire extinguisher (Class D for lithium fires) nearby.
  • Store batteries and nickel strips in a safe, dry, non-conductive environment, away from children and pets.
  • If you are unfamiliar with battery pack assembly or spot welding, seek professional guidance or extensive training before attempting.

3. Product Overview

The EOENKK Pure Nickel Sheet is specifically designed for creating robust and low-resistance connections between 18650 lithium battery cells. Made from pure nickel, these strips offer excellent conductivity and corrosion resistance, crucial for reliable battery pack performance.

Overview of 18650 lithium battery pure nickel sheets with batteries, showing material and thickness.

Figure 1: Overview of 18650 lithium battery pure nickel sheets. Material: pure nickel, Thickness: 0.15mm.

4. Setup and Preparation

  1. Gather Materials: Ensure you have your 18650 lithium battery cells, the EOENKK pure nickel sheets, a spot welder, and appropriate safety gear.
  2. Inspect Batteries: Check each 18650 battery cell for any physical damage, swelling, or signs of leakage. Only use healthy cells.
  3. Clean Terminals: Lightly clean the positive and negative terminals of the battery cells to ensure good electrical contact. Isopropyl alcohol can be used, ensuring it evaporates completely before proceeding.
  4. Prepare Nickel Strips: Select the appropriate length and configuration of nickel strips for your battery pack design. The strips are pre-cut for convenience.
  5. Multiple 18650 batteries and various pure nickel connection strips.

    Figure 2: Assortment of 18650 batteries and pure nickel connection strips.

  6. Position Nickel Strips: Carefully place the nickel strip onto the battery terminal where the connection is to be made. Ensure it lies flat and covers the contact area adequately.
  7. Pure nickel strips positioned on the positive and negative terminals of 18650 batteries.

    Figure 3: Nickel strips correctly placed on 18650 battery terminals, ready for spot welding.

    A gloved hand demonstrating the proper placement of a pure nickel strip onto an 18650 battery terminal.

    Figure 4: Close-up of a nickel strip being positioned on a battery terminal.

5. Operating Instructions (Spot Welding)

Once the nickel strips are positioned, proceed with spot welding according to your spot welder's instructions. The following are general guidelines:

  1. Spot Welder Settings: Adjust your spot welder's power and pulse settings based on the nickel strip thickness (0.15mm) and battery terminal material. Start with lower settings and gradually increase until a strong weld is achieved.
  2. Welding Technique:
    • Apply firm, even pressure with the spot welder probes onto the nickel strip and battery terminal.
    • Ensure both probes make good contact with the nickel strip, directly above the battery terminal.
    • Perform quick, precise welds. Avoid prolonged contact that could overheat the battery.
    • Typically, 2-4 spot welds per connection point are recommended for strength and reliability.
  3. Inspect Welds: After welding, visually inspect each joint. A good weld should be clean, secure, and not easily peeled off. Gently tug on the strip to test its strength. If a weld is weak, adjust settings and re-weld, or replace the strip if necessary.
  4. Series/Parallel Connections: Continue connecting all battery cells in your desired series and/or parallel configuration using the nickel strips.

6. Maintenance and Storage

6.1 Product Maintenance

The pure nickel sheets themselves require minimal maintenance. Ensure they remain clean and free from contaminants before use.

6.2 Storage

Store unused nickel sheets in a dry, cool environment, away from direct sunlight, moisture, and corrosive chemicals. Keep them in their original packaging or a sealed container to prevent oxidation and physical damage. Proper storage helps maintain their conductivity and weldability.

7. Troubleshooting Common Issues

  • Poor Welds:
    • Cause: Insufficient power, poor contact, dirty terminals/strips, incorrect probe pressure.
    • Solution: Increase spot welder power, clean battery terminals and nickel strips, apply firmer and more even probe pressure, ensure probes are sharp and clean.
  • Overheating Batteries:
    • Cause: Excessive spot welder power, prolonged contact time, too many welds in one spot.
    • Solution: Reduce spot welder power, use shorter pulse durations, allow batteries to cool between welds, distribute welds evenly.
  • Nickel Strip Corrosion:
    • Cause: Exposure to moisture or corrosive environments during storage.
    • Solution: Ensure proper storage in a dry, sealed container. Discard corroded strips as they may lead to poor connections.

8. Specifications

FeatureDetail
Product Type18650 Lithium Battery Pure Nickel Sheet / Connection Strip
BrandEOENKK
MaterialPure Nickel
Thickness0.15mm
Compatibility18650 Lithium-ion Battery Cells
Package Quantity Options20 pieces, 50 pieces (available in different product variations)
Close-up of two pure nickel strips, detailing material, thickness, and quantity (20 pcs).

Figure 5: Detailed view of pure nickel strips with specifications.

9. User Tips

While no specific user reviews or Q&A were available for this product, here are some general tips for working with battery connection sheets:

  • Practice Makes Perfect: If new to spot welding, practice on scrap materials or old battery cells (safely discharged) to dial in your welder settings before working on your final battery pack.
  • Battery Holders: Use plastic 18650 battery holders or jigs to keep cells securely in place during welding, preventing accidental short circuits and ensuring consistent spacing.
  • Ventilation: Always work in a well-ventilated area to disperse any fumes from welding or potential battery off-gassing.
  • Temperature Monitoring: Consider using an infrared thermometer to monitor battery cell temperatures during welding to prevent overheating.

10. Warranty and Support

For specific warranty information regarding your EOENKK Pure Nickel Sheets, please refer to the seller's terms and conditions at the time of purchase. If you encounter any issues or have questions about the product, please contact the seller directly through the platform where the purchase was made.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.