eletechsup CTUIB01

Contents

Eletechsup Voltage to Current Converter Module User Manual

Model: CTUIB01

Brand: eletechsup

1. Product Overview

This Eletechsup Voltage to Current Converter Module (Model CTUIB01) is designed to convert various voltage signals into standard current signals. It supports input voltage ranges of 0-5V, 0-10V, and 0-24V, which can be converted into 4-20mA or 0-20mA current outputs. This module is ideal for applications requiring analog signal conversion, such as with PLCs and RS485 sensors.

2. Specifications

Feature Specification
Working Voltage DC 7-30V (Power supply voltage must be > input voltage by 2V)
Working Current 10-30mA (related to output current)
Voltage Signal Input Range 0-5V / 0-10V / 0-24V (Adjustable to 0-2.5V, 0-3.3V, 0-4.096V, 0-5V, 0-10V, 0-15V, 0-20V, 0-24V)
Current Signal Output Range 4-20mA
Accuracy 1%
Dimensions 42mm * 21mm * 14mm
Weight 8 grams
Application Alarm systems, industrial control
Type Module

3. Package Contents

  • 1 x Eletechsup Voltage to Current Converter Module (Specific version and quantity as chosen at purchase)

4. Safety Warnings

Important Safety Information:

  • Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.

5. Setup and Wiring

Proper wiring is crucial for the correct operation of the module. Refer to the diagrams below for connection details.

Wiring Diagram for Voltage to Current Converter Module

Figure 1: Detailed Wiring Diagram. This diagram illustrates the connections for power supply, voltage signal input, and current signal output. The power supply (DC 7-30V) connects to VCC and GND. The voltage signal source connects to Vi+ and Vi-. The current signal output (4-20mA/0-20mA) connects to OUT and GND. Note that the power supply voltage should be at least 2V greater than the highest voltage signal input.

Onboard Components of the V/I Converter Module

Figure 2: Onboard Resources and Component Layout. This image highlights key components such as the power indicator, HIGH and LOW potentiometers for current regulation, and input/output terminals. The brightness of the indicator light changes with the output current.

Application Block Diagram and Wiring Diagram

Figure 3: Simplified Application Block Diagram. This diagram provides a conceptual overview of the module's function, showing the detection voltage input (Vi+/Vi-), power supply (VCC/GND), and current output (OUT 0/4-20mA).

Wiring Steps:

  1. Connect the DC power supply (7-30V) to the VCC and GND terminals. Ensure the power supply voltage is at least 2V higher than the maximum input voltage signal.
  2. Connect your 4-20mA ammeter or receiving device to the OUT and GND terminals.
  3. Connect your voltage signal source to the Vi+ and Vi- terminals.
  4. Ensure the output current does not exceed 30mA, as this can damage the chip.

6. Operation and Calibration

The module's output current range can be precisely calibrated using the onboard potentiometers.

Potentiometer Adjustment Method:

  • LOW Potentiometer: Adjusts the minimum output current (lower limit). Turning clockwise makes the output smaller; turning counter-clockwise makes it larger.
  • HIGH Potentiometer: Adjusts the maximum output current (upper limit). Turning clockwise makes the output larger; turning counter-clockwise makes it smaller.

Calibration Procedure (for 0-5V/0-10V/0-24V to 4-20mA):

To ensure accurate parameters, allow the board to output 20mA current for 3 minutes before starting calibration.

  1. Perform wiring as described in Section 5.
  2. Input a 0V voltage signal to the module.
  3. Adjust the LOW potentiometer until the current output reads 4.00mA on your ammeter.
  4. Input the highest voltage signal for your desired range (e.g., 5V for 0-5V range, 10V for 0-10V range, 24V for 0-24V range).
  5. Adjust the HIGH potentiometer until the current output reads 20.00mA on your ammeter.

Example: Changing from 0-5V to 0-10V Version

If you have a 0-5V version and wish to calibrate it for a 0-10V input range:

  1. Wire the module as per the diagram.
  2. Input 0V voltage signal, adjust the LOW potentiometer to achieve 4.00mA output.
  3. Input 5V voltage signal, adjust the HIGH potentiometer to achieve 10.00mA output.
  4. Input 10V voltage signal, adjust the HIGH potentiometer to achieve 20.00mA output.

Video 1: Calibration Demonstration. This video shows the process of calibrating the voltage to current converter module, including adjusting the potentiometers to set the desired output range.

Calibration Steps Diagram

Figure 4: Visual Guide for Calibration. This diagram visually reinforces the calibration steps, showing the input voltage signal source, power supply, current signal output, and the LOW/HIGH potentiometers for adjustment.

7. Maintenance

  • After use, turn off the device and store it in a dry place.
  • Keep the module away from dust and moisture to prevent damage.
  • Regularly inspect the module for any visible damage to components or wiring.
  • Clean the module gently with a dry, soft cloth if necessary. Do not use liquids or abrasive cleaners.

8. Troubleshooting

  • Output Current Not Accurate: If the output current is not accurate, follow the detailed calibration procedure in Section 6. Ensure the power supply voltage meets the minimum requirement (at least 2V greater than the highest input voltage signal).
  • Module Not Functioning: Check all wiring connections for correctness and ensure the power supply is within the DC 7-30V range. Verify that the input voltage signal is present.
  • Module Overheating/Damage: Ensure the output current does not exceed 30mA. Exceeding this limit can burn the chip. Verify that the power supply voltage is not excessively high.

9. User Tips

  • Users have found this module to be easy to calibrate, making setup straightforward.
  • For best results during calibration, perform the pre-calibration step of letting the board output 20mA for 3 minutes.

10. Further Information and Support

For a comprehensive user manual and additional documents, please refer to the official PDF manual:

User manual (PDF) reference: View User Manual PDF

For any further assistance or technical support, please contact Eletechsup customer service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.