hiwheel KCQ8.5 Inch with APP Plus

Contents

Kechuangqi APP Plus Scooter Controller Instruction Manual

Model: KCQ8.5 Inch with APP Plus | Brand: hiwheel

1. Safety Information

⚠️ Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage.

Always ensure all connections are secure and properly insulated to prevent short circuits. Do not operate the scooter controller if any components appear damaged or wet. Keep the controller away from water and extreme temperatures.

2. Product Overview

This manual provides instructions for the 350W 36V 15A Kechuangqi APP Plus scooter controller, designed for 8.5-inch electric scooters. It features Bluetooth connectivity for APP control, allowing for enhanced customization and monitoring.

Components Included:

  • Scooter Controller Unit
  • Display Unit
  • Accelerator
  • Headlight
  • Taillight
  • Brake Lever
  • Display Data Line
  • Bluetooth Module (for APP control)
Complete set of scooter controller components
Figure 2.1: Complete set of scooter controller components.

3. Specifications

ParameterValue
VoltageDC 36V
Rated Power350W
Undervoltage Protection30V
Current15A (Upgraded for more power)
Max Speed30 km/h
TypeController
CustomizationYes
Model NumberKCQ8.5 Inch with APP Plus

Physical Dimensions:

Dimensions of the scooter controller unit
Figure 3.1: Controller dimensions (9cm x 4.8cm x 3.6cm).

4. Setup and Installation

Before installation, ensure your scooter's existing controller interface is compatible with this unit. Refer to the diagrams below for proper wiring.

4.1 Wiring Connections

Carefully connect each component to the controller as indicated in the diagram. Pay close attention to the motor phase lines, hall lines, display, taillight, and battery connections.

Main controller wiring diagram showing connections for motor, hall, display, taillight, and battery (XT60)
Figure 4.1: Main controller wiring diagram. Connect battery via XT60 connector.
Display unit with labeled connections for Accelerator, Headlight, and Brake
Figure 4.2: Display unit connections for Accelerator, Headlight, and Brake.
Close-up of the XT60 battery connector on the controller
Figure 4.3: Close-up of the XT60 battery connector.

4.2 Motor Wiring Adjustment

If the motor experiences noise, does not run smoothly, shakes, or runs in reverse, adjustments to the hall lines or motor phase lines may be necessary. Refer to the diagram below for adjustment methods.

Motor wiring adjustment guide for phase and hall lines to resolve motor issues
Figure 4.4: Motor wiring adjustment guide. Test 6 methods for hall lines to ensure smooth operation. If the motor runs smoothly but in reverse, change the phase line connection according to the 6 methods shown until it runs correctly.

4.3 APP Installation

Scan the QR code below to download and install the companion mobile application for your scooter controller. The app allows you to control various functions and settings.

QR code for downloading the scooter control APP
Figure 4.5: QR code for APP download. The app adapts to your mobile phone's system language.

5. Operating Instructions

5.1 Basic Operations

  • Boot: Long press the power button for approximately 1 second. The buzzer will sound twice.
  • Shutdown: Press and hold the power button for 3 seconds. The buzzer will sound twice.
  • Lights: In the power-on state, short press the power button once (within 1 second) to turn on the front and rear lights. The headlights will be continuously on, and the taillights will flash.
  • Brake: The scooter uses both electronic and disc brakes. When braking, the taillight will illuminate continuously.

5.2 Speed and Gear Shift

  • Gear Shift: In the power-on state, the default is low-speed gear. Press the button twice (within one second) to switch gear positions. Green indicates low gear (approx. 15±2 km/h); Red indicates high gear (approx. 25±2 km/h).
  • Constant Speed Cruise: Maintain a stable speed for approximately 6 seconds to automatically activate cruise control. Once fixed, the throttle can be released. To disengage cruise control, press the brake or push the throttle again to return to manual mode.

5.3 Battery Display and Alarms

  • Battery Level Display:
    • 33V-36V: First light is on.
    • 36V-37V: One or two lights are on.
    • 37V-38.5V: One or two lights are on.
    • 38.5V or more: All four lights are on.
  • Low Voltage Alarm: If the battery voltage drops below 33V, the first light will flash, and the buzzer will sound 6 times. The speed limit will be approximately 15 km/h. To release the low voltage state and return to normal operation, the throttle must return to its initial position once the power returns to 37V.

5.4 Automatic Shutdown

The scooter controller will automatically shut down after 10 minutes of no operation to conserve battery life.

Scooter control APP interface showing speed control, riding time, mileage, and total mileage, with map, unlock, and power buttons
Figure 5.1: Scooter control APP interface (English and French examples).

6. Troubleshooting

The display unit may show error codes to indicate specific issues. Refer to the table below for common error codes and their solutions.

Error CodeDescriptionSolution
E0Temperature protectionMotor has reached temperature limit. Allow motor to cool down below the set value for normal riding.
E1Motor Hall failureMotor Hall is damaged. Replace the motor.
E2MOS tube failure1. Check motor phase wires for short circuits or damage; replace motor if necessary. 2. Replace the controller.
E3Brake failure1. Replace the brake lever. 2. Ensure the brake lever returns to its neutral position before starting.
E4Accelerator failure1. Replace the speed control handle (accelerator). 2. Ensure the speed control handle returns to its original position before starting.
E5Undervoltage protectionThe supply voltage is below the controller's minimum. Charge or replace the battery.
E6Controller/instrument communication failure1. Check communication line connection. 2. Check motor phase or Hall lines for damage/leakage. 3. Replace the motor.
E7Overvoltage protectionThe supply voltage is above the controller's maximum. Replace battery or motor phase wire to match controller voltage.
E8Controller operational amplifier failureController is damaged (e.g., water ingress). Replace the controller.
E9Stalled rotor fault1. Remove any obstacles preventing motor rotation. 2. Verify correct wiring sequence between motor and controller.

7. User Tips

  • Wiring Adjustments: Some users have found that adjusting the position of the engine control lines (green, blue, yellow, black, and red) can resolve operational issues. Ensure these wires are correctly connected without touching the spring.
  • Start Mode Customization: The controller may default to a 'Non-zero start' (kick start) mode, requiring an initial push to engage the motor. If you prefer an immediate start, you can change this setting to 'Zero start' via the mobile application. Navigate to the 'Setting' menu in the app and select 'Start mode' to adjust this preference.
APP settings screen for 'Start mode' (Zero start / Non-zero start) and other options
Figure 7.1: APP settings for 'Start mode' (Zero start / Non-zero start).

8. Maintenance

Regular maintenance ensures the longevity and optimal performance of your scooter controller.

  • Keep Clean: Periodically clean the controller and its connections to prevent dust and debris buildup.
  • Inspect Wiring: Regularly check all wires and connectors for signs of wear, fraying, or corrosion. Replace any damaged components immediately.
  • Software Updates: Check the mobile application periodically for any available firmware updates for the controller to ensure you have the latest features and bug fixes.
  • Storage: When not in use for extended periods, store the scooter and controller in a dry, cool place, away from direct sunlight and extreme temperatures. Ensure the battery is charged to an appropriate storage level (typically 50-80%) to prevent degradation.

9. Warranty and Support

For warranty information or technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase. Any unauthorized modifications or improper installation may void the product warranty.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.