hiwheel KCQ 36V350W

Contents

KCQ 36V350W15A Electric Scooter Controller Display Instrument Kit User Manual

For Xiaomi M365/Pro 8.5-inch Electric Scooters

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the KCQ 36V350W15A Electric Scooter Controller Display Instrument Kit. This kit is designed to be compatible with Xiaomi M365/Pro 8.5-inch electric scooters, offering an enhanced control experience.

The controller features ultra-quiet operation, minimizing motor torque ripple for a smooth, vibration-free, and comfortable ride. Utilizing a Field Oriented Control (FOC) algorithm, it boasts high conversion efficiency, which helps reduce controller temperature rise and extend battery life.

2. Safety Information

⚠️ Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage.

  • Terminal Connection: Reversing the positive and negative terminals is strictly prohibited, as it will immediately burn out the controller. Ensure all terminals are fully inserted and securely connected to prevent short circuits or poor contact.
  • Voltage Compatibility: The controller must operate within the specified voltage range; do not exceed the rated voltage.
  • Power Matching: The controller's power rating must match the motor's power rating. Do not use an undersized controller for an oversized motor.
  • Environmental Conditions: Do not use or store the controller in damp, high-temperature, or flammable/explosive environments.
  • Installation Expertise: Installation should be performed by qualified personnel with electrical expertise. Non-professionals must not disassemble or attempt repairs.

3. Product Overview

The KCQ 36V350W15A kit typically includes the following components:

KCQ 9-piece controller kit components

Figure 3.1: Overview of the 9-piece KCQ controller kit components, including controller, accelerator, tail light, headlight, Pro instrument with APP, APP QR code, instrument panel cover, waterproof sleeve, and brake lever.

Main Components:

  • Controller: The central processing unit for motor control.
  • Accelerator: For speed input.
  • Tail Light: Rear illumination.
  • Headlight: Front illumination.
  • Pro Instrument with APP: Digital display and interface for APP connectivity.
  • APP QR Code: For downloading the companion application.
  • Instrument Panel Cover: Protective cover for the display.
  • Waterproof Sleeve: For protecting connections.
  • Brake Lever: For braking input.

This product is equipped with two additional adapters to ensure compatibility. If the interface of the controller is inconsistent with the Hall wire and battery interface of your scooter motor, these adapter cables can be used to better connect them.

KCQ controller kit with scooter and adapter cables

Figure 3.2: The complete KCQ controller kit shown with a scooter and the included battery (XT60 to XT30 conversion) and Hall wire adapter cables (Figure 1 inset).

Controller Wiring Overview:

KCQ controller with labeled wiring

Figure 3.3: Detailed view of the controller with labeled connections for XT60 Battery interface, Motor phase line, Communication line, Tail light line, and Hall line.

Display Instrument Wiring Overview:

KCQ display instrument with labeled wiring

Figure 3.4: Detailed view of the display instrument with labeled connections for Communication line, Accelerator line (white interface), Brake line (red interface), and Headlight line.

4. Specifications

FeatureSpecification
Product NameKCQ 8.5-inch Electric Scooter Controller Kit
Rated VoltageDC 36V
Current Limit15A ± 0.5A
Compatible Motor Power350W
Battery ConnectorXT60
Max Speed (Default)25 km/h (16 mph)
Speed Gears (Default)D gear: 20 km/h (13 MPH), S gear: 25 km/h (16 mph)
Speed Gears (After Limit Lift)E gear: 15 km/h (9 MPH), D gear: 25 km/h (16 MPH), S gear: 32 km/h (20 MPH)
Key FeaturesSpeed Control, Cruise Control, Self-Diagnostic, Low Voltage Protection, APP Connectivity
Controller Dimensions (approx.)10.4 cm (L) x 8.8 cm (W) x 4.9 cm (H)
Display Dimensions (approx.)7.2 cm (L) x 2.3 cm (W)
KCQ controller and display dimensions

Figure 4.1: Physical dimensions of the KCQ controller and display unit.

5. Installation Steps

Follow these steps carefully to install your new KCQ controller kit.

Step 1: Removal and Preparation

  1. Open the Footrest Cover: Locate and open the footrest cover of your electric scooter to access the original controller. The original controller is typically a rectangular box with an aluminum heat sink and multiple connectors.
  2. Disconnect All Connections: Carefully unplug the following wires from the old controller:
    • Motor phase wires (thick wires)
    • Motor Hall sensor wires
    • Power supply wires
    • All function wires (throttle wires, brake wires, instrument panel wires, lighting wires, etc.)
  3. Remove the Old Controller: Unscrew and remove the old controller from its mounting position.

Step 2: Install the New KCQ Controller

  1. Position Alignment: Place the new KCQ controller in the original controller's location. Ensure the heat dissipation surface faces outward and remains unobstructed. Make any necessary adjustments or expand the installation space if needed.
  2. Initial Securing: Securely fasten the new controller to the frame using screws. Ensure it is firmly fixed to prevent loosening from riding vibrations.

Step 3: Wiring Connection (The Most Critical Step)

Principle: Always connect power cables (thick wires) first, then signal cables (thin wires). Ensure all connectors are fully seated.

  1. Connecting Power Cables: Connect the negative terminal first, then the positive terminal. After connecting, you may temporarily leave the power off.
  2. Connecting Motor Wires:
    • Motor Phase Wires: Connect the controller's three thick phase wires (yellow, green, blue) to the corresponding three phase wires of the motor. Initially, connect them arbitrarily and temporarily secure with zip ties without sealing them. The correct phase will be matched through debugging later (see Section 6).
    • Motor Hall Sensor Wires: Locate the Hall sensor connectors on both the controller and motor. These typically feature a foolproof design for direct plug-and-play connection. If connectors do not align, manually match each wire according to the wire sequence definition. Secure connections with solder and insulate using heat shrink tubing.
  3. Connect Control Signal Wires (typically plug-in connectors):
    • Throttle Grip: Connect the throttle grip wire to the controller. New kits usually include a new throttle grip for direct plug-in connection.
    • Brake: Connect the brake cable.
    • Instrument Panel/Display: Connect the corresponding instrument wires to display speed, battery level, mode, etc.
    • Other Functions: Connect wires for features like lights, cruise control, or anti-theft alarms as needed.

After completing all connections, conduct a thorough inspection to ensure no wiring has been overlooked or improperly connected.

6. Wiring Connection Details and Adjustments

This section provides further details on specific wiring connections and adjustments for optimal performance.

Adapter Cables

If the controller battery interface or Hall wire interface is inconsistent with your scooter's battery or motor interface, use the provided adapter cables.

Battery and Hall wire adapter cables

Figure 6.1: Battery adapter (XT60 to XT30 conversion) and Hall wire adapter cable for compatibility.

Motor Phase Line Adjustment

If the motor is running abnormally or in the opposite direction after initial connection, you need to adjust the phase lines. Change the wiring as shown in the following figure until the motor runs well (e.g., swap yellow and green lines).

Motor phase line adjustment diagram

Figure 6.2: Diagram illustrating various configurations for motor phase line adjustment (Y=Yellow, G=Green, B=Blue). Adjust until the motor runs smoothly.

Hall Line Adjustment

If the motor shakes, vibrates, or makes noise but doesn't run smoothly, you may need to adjust the Hall lines. Test the six methods shown in the diagram below one by one and choose the configuration that results in the smoothest operation.

Hall line adjustment diagram

Figure 6.3: Diagram illustrating six methods for Hall line adjustment (Y=Yellow, G=Green, B=Blue). Test each configuration to find the optimal one for smooth motor operation.

7. Operating Instructions

The KCQ controller kit integrates with a dedicated mobile application (APP) for advanced control and monitoring.

Display Instrument

The display instrument provides real-time information about your scooter's status, including speed, battery level, and current mode.

APP main display screen

Figure 7.1: Main display screen of the companion APP, showing current speed, cycling time, total mileage, battery level, headlight status, and lock status.

APP Features and Settings

The APP allows for customization of various parameters, including speed control, cruise control, and self-diagnostic functions.

  • Speed Gears: The default speed gears are D gear (20 km/h / 13 MPH) and S gear (25 km/h / 16 mph).
  • Lifted Speed Limit: After lifting the speed limit via the APP, the speed gears become E gear (15 km/h / 9 MPH), D gear (25 km/h / 16 MPH), and S gear (32 km/h / 20 MPH).
APP advanced speed settings

Figure 7.2: Advanced settings in the APP, allowing adjustment of maximum speed limits for the first, second, and third gears. The maximum speed limit can be adjusted up to 33 KM/H.

  • Start Mode and Cruise Control: The APP allows you to set the scooter's startup mode (e.g., non-zero start) and enable/disable cruise control.
APP settings for start mode and cruise control

Figure 7.3: APP settings interface, showing options to modify Bluetooth name, single slot setting, taillight behavior, start mode (Non-zero start), and cruising at fixed speed (cruise control).

8. Troubleshooting (Fault Codes and Solutions)

The display instrument will show error codes if a fault occurs. Refer to the table below for common fault codes and their solutions.

Fault CodeDescriptionPossible CauseSolution
E0Thermal ProtectionMotor reached thermal protection threshold.Wait for the motor to cool down until the temperature falls below the set value before resuming normal operation.
E1Motor Hall Sensor FailureMotor Hall sensor damaged.Replace motor.
E2MOSFET FailureShort circuit between motor phase wires; Internal controller component damage.Inspect motor phase wires for insulation damage or other issues; replace motor. If issue persists, replace controller.
E3Brake FailureDamaged brake lever; Brake lever not reset before startup.Replace brake lever. Release brake lever to reset; if error persists, replace brake lever.
E4Throttle FaultThrottle grip damaged; Throttle grip not reset before startup.Replace throttle grip. Release throttle grip to reset; if error persists, replace throttle grip.
E5Undervoltage ProtectionSupply voltage below controller's minimum threshold.Charge or replace battery.
E6Controller/Instrument Communication FailureInstrument and controller cannot communicate.Check communication cable connections. Inspect motor phase wires or Hall sensor wires for damage/leakage. Replace motor.
E7Overvoltage ProtectionSupply voltage exceeds controller's maximum threshold.Replace battery with controller-matched voltage or repair motor phase/Hall wire insulation damage causing leakage.
E8Controller Op-Amp FailureWater ingress damaging internal components or other internal component damage.Replace the controller.
E9Stall FaultObstacles prevent motor rotation, causing motor lockup; Incorrect wiring sequence between motor and controller.Loosen the throttle grip and remove the obstruction. Return the motor to the controller manufacturer for re-calibration.

9. User Tips

  • Always perform a thorough check of all connections after installation and before each ride to ensure safety and proper function.
  • Regularly inspect all wires for signs of wear, fraying, or damage. Address any issues promptly to prevent malfunctions.
  • Utilize the companion APP to customize speed settings, enable cruise control, and monitor your scooter's performance for an optimized riding experience.
  • Ensure your scooter's battery voltage is compatible with the controller's specifications to prevent damage and ensure efficient operation.
  • Keep the APP QR code handy for easy access to the application download.

10. Warranty and Support

Warranty Information

Please note that the product warranty typically does not cover water damage and wire damage. Always ensure proper sealing and protection of all components, especially in damp conditions.

Support and Contact

For any questions or assistance regarding the KCQ 36V350W15A Electric Scooter Controller Display Instrument Kit, or for general electric scooter and E-bike related issues, please use the following contact information:

  • WhatsApp: 0086 13425108591
  • WeChat: MXYG1688
  • Facebook: 0086 13425108591

The seller offers free returns within 90 days. For details on this policy, please refer to the seller's terms and conditions.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.