PowMr POW-HVM10.2M

Contents

PowMr 10.2KW Hybrid Solar Inverter User Manual

Model: POW-HVM10.2M

1. About This Manual

1.1 Purpose

This manual describes the assembly, installation, operation, and troubleshooting of this unit. Please read this manual carefully before installations and operations. Keep this manual for future reference.

1.2 Scope

This manual provides safety and installation guidelines as well as information on tools and wiring.

2. Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  1. Before using the unit, read all instructions and cautionary markings on the unit, the batteries and all appropriate sections of this manual.
  2. CAUTION --To reduce risk of injury, charge only deep-cycle lead acid type rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.
  3. Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
  4. To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
  5. CAUTION – Only qualified personnel can install this device with battery.
  6. NEVER charge a frozen battery.
  7. For optimum operation of this inverter/charger, please follow required spec to select appropriate cable size. It's very important to correctly operate this inverter/charger.
  8. Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts and could cause an explosion.
  9. Please strictly follow installation procedure when you want to disconnect AC or DC terminals. Please refer to INSTALLATION section of this manual for the details.
  10. One piece of 150A fuse is provided as over-current protection for the battery supply.
  11. GROUNDING INSTRUCTIONS -This inverter/charger should be connected to a permanent grounded wiring system. Be sure to comply with local requirements and regulation to install this inverter.
  12. NEVER cause AC output and DC input short circuited. Do NOT connect to the mains when DC input short circuits.
  13. Warning!! Only qualified service persons are able to service this device. If errors still persist after following troubleshooting table, please send this inverter/charger back to local dealer or service center for maintenance.

3. Introduction

This is a multi-function inverter/charger, combining functions of inverter, solar charger and battery charger to offer uninterruptible power support with portable size. Its comprehensive LCD display offers user-configurable and easy-accessible button operation such as battery charging current, AC/solar charger priority, and acceptable input voltage based on different applications.

3.1 Features

  • Pure sine wave inverter
  • Configurable input voltage range for home appliances and personal computers via LCD setting
  • Configurable battery charging current based on applications via LCD setting
  • Configurable AC/Solar Charger priority via LCD setting
  • Compatible to mains voltage or generator power
  • Auto restart while AC is recovering
  • Overload/ Over temperature/ short circuit protection
  • Smart battery charger design for optimized battery performance
  • Cold start function
  • Inverter running without battery.
  • Output power factor 1.0
  • High PV input voltage range (90~500VDC).
  • WIFI & GPRS available for iOS and Android.
  • Built-in anti-dusk kit for harsh environment.
  • Built-in 160A MPPT solar charge controller.
  • One-click restoration to factory Settings.
  • Dual AC output and dual PV input.
  • Built-in Lithium battery automatic activation.
  • Touch button interface.

3.2 Basic System Architecture

The following illustration shows basic application for this inverter/charger. It also includes following devices to have a complete running system: Generator or Utility, PV modules. Consult with your system integrator for other possible system architectures depending on your requirements. This inverter can power all kinds of appliances in home or office environment, including motor-type appliances such as tube light, fan, refrigerator and air conditioner.

Diagram illustrating the all-in-one solar charge inverter system connecting PV panel, generator, utility, and 48V battery to household loads
Figure 1: Hybrid Power System Diagram. This diagram shows how the inverter connects to PV panels, a generator or utility grid, a 48V battery, and powers household loads.

3.3 Product Overview

PowMr 10.2KW Hybrid Solar Inverter with specifications overlay
Front view of the PowMr 10.2KW Hybrid Solar Inverter, highlighting its MPPT 230VAC, 10.2KW 48V Pure Sine Wave, 160A Charge Current, and 90-500VDC PV Voltage Range.
PowMr 10.2KW Hybrid Solar Inverter dimensions and key features like 160A MPPT, 10200W PV array power, dual AC output
Dimensions and key specifications of the PowMr 10.2KW Hybrid Solar Inverter, including 160A MPPT, 10200W Max PV Array Power, 90-450VDC PV Array MPPT Voltage Range, and Dual AC Output.
PowMr 10.2KW Hybrid Solar Inverter showing RGB light indicators for different working modes (Stationary, Battery, Utility, PV) and three cooling fans with anti-dusk kit
Smart Design features of the inverter, including RGB lights for different working modes (White for Stationary, Red for Battery, Blue for Utility, Purple for PV) and a three-cooling fan system with an anti-dusk kit for harsh environments.
Diagram showing dual MPPT input for solar panels and compatibility with multiple battery types (FLD, GEL, SLD, AGM, LI) with Li Battery Activation details
Dual MPPT Input capability with Max PV Array Power of 10200W and MAX PV Input of 500VDC. The inverter is compatible with multiple battery types including FLD, GEL, SLD, AGM, and LI, and features Li Battery Activation.
Front, side, and rear views of the PowMr 10.2KW Hybrid Solar Inverter, highlighting connection ports
Various product views showing the front, side, and rear panels of the inverter, detailing the layout of controls and connection ports.
Product label showing model number POW-HVM10.2M, PV input, Grid/AC output, Two-load output power, and battery specifications
Product label with detailed specifications for the POW-HVM10.2M model, including PV input, Grid/AC output, Two-load output power, and battery specifications.
Diagram showing 15 intelligent protection modes including charge/discharge protection, short-circuit, reverse connection, battery overvoltage, over temperature, and overload protection
Intelligent Protection Systems: The inverter features 15 intelligent protection modes for enhanced safety and reliability, including charge low/high temperature, discharge low/high temperature, overcurrent, undervoltage, short-circuit, solar panel reverse connection, battery overvoltage, over temperature, and overload protection.

4. Setup and Installation

4.1 Unpacking and Inspection

Before installation, please inspect the unit. Be sure that nothing inside the package is damaged. You should have received the following items:

  • The unit x 1
  • User manual x 1
  • Ring terminal x 1
  • MC4 terminal head x 2

4.2 Preparation

Before connecting all lines, remove the screws under the machine and remove the bottom cover plate.

4.3 Mounting the Unit

Consider the following points before selecting where to install:

  • Do not mount the inverter on flammable construction materials.
  • Mount on a solid surface.
  • Install this inverter at eye level in order to allow the LCD display to be read at all times.
  • For proper air circulation to dissipate heat, allow a clearance of approx. 20 cm to the side and approx. 50 cm above and below the unit.
  • The ambient temperature should be between 0°C and 55°C to ensure optimal operation.
  • The recommended installation position is to be adhered to the wall vertically.
  • Make sure that other objects and surfaces are left with enough space from the machine to ensure adequate heat dissipation and that there is enough room to remove the wires.

WARNING: SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY.

Install the unit by screwing two screws. It's recommended to use M4 or M5 screws.

4.4 Battery Connection

CAUTION: For safety operation and regulation compliance, it's requested to install a separate DC over-current protector or disconnect device between battery and inverter. It may not be requested to have a disconnect device in some applications, however, it's still requested to have over-current protection installed. Please refer to typical amperage in below table as required fuse or breaker size.

WARNING! All wiring must be performed by a qualified personnel.

WARNING! It's very important for system safety and efficient operation to use appropriate cable for battery connection. To reduce risk of injury, please use the proper recommended cable as below.

Recommended Battery Cable Size
ModelWire SizeCable (mm²)Torque value (max)
8.2KW/10.2KW1 x 2AWG252 Nm

Please follow below steps to implement battery connection:

  1. Remove insulation sleeve 18 mm for positive and negative conductors.
  2. Suggest to put bootlace ferrules on the end of positive and negative wires with a proper crimping tool.
  3. Connect all battery packs as below chart.
Diagram showing how to connect multiple 12V battery packs in series to the inverter
Battery connection diagram for 12V battery packs in series to the inverter.
  1. Insert the battery wires flatly into battery connectors of inverter and make sure the bolts are tightened with torque of 2 Nm in clockwise direction. Make sure polarity at both the battery and the inverter/charge is correctly connected and conductors are tightly screwed into the battery terminals. Recommended tool: #2 Pozi Screwdriver.

WARNING: Shock Hazard Installation must be performed with care due to high battery voltage in series.

CAUTION!! Before making the final DC connection or closing DC breaker/disconnector, be sure positive (+) must be connected to positive (+) and negative (-) must be connected to negative (-).

4.5 AC Input/Output Connection

CAUTION!! Before connecting to AC input power source, please install a separate AC breaker between inverter and AC input power source. This will ensure the inverter can be securely disconnected during maintenance and fully protected from over current of AC input. The recommended spec of AC breaker is 63A for 8.2KW/10.2KW.

CAUTION!! There are two terminal blocks with “IN” and “OUT” markings. Please do NOT mis-connect input and output connectors.

WARNING! All wiring must be performed by a qualified personnel.

WARNING! It's very important for system safety and efficient operation to use appropriate cable for AC input connection. To reduce risk of injury, please use the proper recommended cable size as below.

Suggested Cable Requirement for AC Wires
ModelGaugeCable (mm²)Torque Value
8.2KW/10.2KW10 AWG61.2 Nm

Please follow below steps to implement AC input/output connection:

  1. Before making AC input/output connection, be sure to open DC protector or disconnector first.
  2. Remove insulation sleeve 10mm for six conductors. And shorten phase L and neutral conductor N 3 mm.
  3. Insert AC input wires according to polarities indicated on terminal block and tighten the terminal screws. Be sure to connect PE protective conductor (①) first.
    • ① → Ground (yellow-green)
    • L → LINE (brown or black)
    • N → Neutral (blue)

WARNING: Be sure that AC power source is disconnected before attempting to hardwire it to the unit.

  1. Then, insert AC output wires according to polarities indicated on terminal block and tighten terminal screws.
    • L → LINE (brown or black)
    • N → Neutral (blue)
  2. Make sure the wires are securely connected.

4.6 PV Connection

CAUTION: Before connecting to PV modules, please install separately a DC circuit breaker between inverter and PV modules.

WARNING! It's very important for system safety and efficient operation to use appropriate cable for PV module connection. To reduce risk of injury, please use the proper recommended cable size as below.

Suggested Cable Requirement for PV Wires
ModelWire SizeCable (mm²)Torque value (max)
8.2KW/10.2KW1 x 10AWG61.2 Nm

PV Module Selection:

When selecting proper PV modules, please be sure to consider below parameters:

  1. Open circuit Voltage (Voc) of PV modules not exceeds max. PV array open circuit voltage of inverter.
  2. Open circuit Voltage (Voc) of PV modules should be higher than min. battery voltage.
Inverter Model PV Specifications
INVERTER MODEL8.2KW/10.2KW
Max. PV Array Open Circuit Voltage500Vdc
PV Array MPPT Voltage Range90Vdc~450Vdc

Take 250Wp PV module as an example. After considering above two parameters, the recommended module configurations are listed as below table.

Solar Panel Configuration Example (250Wp PV module)
Solar Panel Spec. (reference)SOLAR INPUT (Min in serial: 6 pcs, max. in serial: 13 pcs)Q'ty of panelsTotal input power
250Wp, Vmp: 30.1Vdc, Imp: 8.3A, Voc: 37.7Vdc, Isc: 8.4A, Cells: 606 pcs in serial6 pcs1500W
8 pcs in serial8 pcs2000W
12 pcs in serial12 pcs3000W
13 pcs in serial13 pcs3250W
12 pieces in serial and 3 sets in parallel36 pcs8200W
10 pieces in serial and 4 sets in parallel40 pcs10200W

PV Module Wire Connection

Step 1: Check the input voltage of PV array modules. The acceptable input voltage of the inverter is 120VDC - 500VDC. Please make sure that the maximum current load of each PV input connector is 10A.

CAUTION: Exceeding the maximum input voltage can destroy the unit!! Check the system before wire connection.

Detailed diagram for PV connector assembly and connection process
PV connector assembly and connection process, showing female and male connector housing, terminals, crimping tool, spanner, and cable preparation.

4.7 Final Assembly

After connecting all wirings, please put bottom cover back by screwing two screws.

4.8 Communication Connection

1. Wi-Fi cloud communication (option):

Please use supplied communication cable to connect to inverter and Wi-Fi module. Download APP and installed from APP store, and Refer to "Wi-Fi Plug Quick Installation Guideline" to set up network and registering. The inverter status would be shown by mobile phone APP or webpage of computer.

2. GPRS cloud communication (option):

Please use supplied communication cable to connect to inverter and GPRS module, and then applied external power to GPRS module. Download APP and installed from APP store, and Refer to “GPRS RTU Quick Installation Guideline" to set up network and registering. The inverter status would be shown by mobile phone APP or webpage of computer.

3. Battery communication

The communication between the battery and the inverter can be realized through the battery communication interface, so that the inverter and the lithium battery can exchange information (Baudrate: 9600).

4. Lithium battery and inverter connection:

Use power cables, communication cables for lithium batteries, and inverters to connect. Note: Lithium battery and inverter positive and negative positions, check the correct installation; The RJ45 connector of the communication cable connects to the BMS port of the inverter, and the other RJ45 connector connects to the RS485 port of the lithium battery; Before connecting, make sure that the lithium battery and inverter are turned off. (It is recommended to install a circuit breaker for the power cables of the lithium battery and the inverter battery interface. Otherwise, a spark may occur.)

Diagram showing the lithium battery communication cable interface and connection ports on the inverter
Lithium battery communication cable interface and connection diagram, showing RJ45 connections to BMS and RS485 ports.

In order to communicate with the lithium battery BMS, you should press the "ENTER" button for a long time, and set the battery type as "LIB-485" in program 05. Then select the matching battery protocol in Program 43.

Battery Type and Protocol Settings
ProgramSettingValueDescription
05Battery typeAGM (05 AGn), Flooded (05 FLd), User Defined (05 USE), Lithium battery mode (05 L I b)Select battery type. For Lithium, choose '05 L I b'.
Lithium battery communication modeL I b 05 485Enable RS485 communication for Lithium batteries.
43Lithium battery protocolPYLON (43 PYL), PACE (43 PAC)Select the specific Lithium battery protocol.

CAUTION: When the battery type is set to "LIB-485", the setting items 12, 13 and 29 are displayed in percentage. When the battery type is set to "LIB-485", the user cannot modify the maximum charging current. When communication fails, the inverter will cut off the output.

5. Operating Instructions

5.1 Power ON/OFF

Once the unit has been properly installed and the batteries are connected well, simply press the On/Off switch (located on the button of the case) to turn on the unit.

5.2 Operation and Display Panel

The operation and display panel, shown below, is on the front panel of the inverter. It includes three indicators, four function keys and an LCD display, indicating the operating status and input/output power information.

LED Indicator Messages
LED IndicatorMessages
INV/AC (Green, Solid On)Output is powered by utility in Line mode.
INV/AC (Green, Flashing)Output is powered by battery or PV in battery mode.
CHG (Green, Solid On)Battery is fully charged.
CHG (Green, Flashing)Battery is charging.
FAULT (Red, Solid On)Fault occurs in the inverter.
FAULT (Red, Flashing)Warning condition occurs in the inverter.
Function Keys Description
Function KeyDescription
ESCTo exit setting mode
UPTo go to previous selection
DOWNTo go to next selection
ENTERTo confirm the selection in setting mode or enter setting mode

5.3 LCD Display Icons

LCD Display Icons and Functions
IconFunction description
AC Input IconIndicates the AC input.
PV Input IconIndicates the PV input.
Input Voltage/Frequency/PV Voltage/Charger Current/Power/Battery Voltage DisplayIndicate input voltage, input frequency, PV voltage, charger current (if PV in charging for 10.2KW models), charger power, battery voltage.
Setting Programs IconIndicates the setting programs.
Warning/Fault Codes IconIndicates the warning and fault codes.
Output Voltage/Frequency/Load Percent/Load in VA/Load in Watt/Discharging Current DisplayIndicate output voltage, output frequency, load percent, load in VA, load in Watt and discharging current.
Overload IconIndicates overload.
Mains Connection IconIndicates unit connects to the mains.
PV Panel Connection IconIndicates unit connects to the PV panel.
AC Bypass IconIndicates load is supplied by utility power.
Utility Charger Circuit IconIndicates the utility charger circuit is working.
DC/AC Inverter Circuit IconIndicates the DC/AC inverter circuit is working.
Mute IconIndicates unit alarm is disabled.

5.4 LCD Setting

After pressing and holding the ENTER button for 3 seconds, the unit will enter setting mode. Press "UP" or "DOWN" button to select setting programs. And then, press "ENTER" button to confirm the selection or ESC button to exit.

Key LCD Settings
ProgramDescriptionSelectable option (Default)Notes
00Exit setting mode00 GOE, 00 GOHOne-button restore setting options.
01Output source priorityUtility first (01 USb), Solar first (01 SOb), SBU priority (01 SBU), MKS priority (01 ntS)Configures the priority of power sources (Utility, Solar, Battery) for loads.
02Maximum charging current10A to 160A (e.g., 02 160 for 160A)Configures total charging current from solar and utility chargers.
03AC input voltage rangeAppliances (03 APL), UPS (03 UPS)Sets acceptable AC input voltage range (90-280VAC for Appliances, 170-280VAC for UPS).
05Battery typeAGM (05 AGn), Flooded (05 FLd), User-Defined (05 USE), LIB-485 (05 L I b)Selects the battery type. For Lithium batteries, choose LIB-485.
06Auto restart when overload occursRestart disable (06 LFd), Restart enable (06 LYE)Enables or disables automatic restart after an overload.
07Auto restart when over temperature occursRestart disable (07 Erd), Restart enable (07 EYE)Enables or disables automatic restart after an over temperature event.
09Output frequency50Hz (09 50), 60Hz (09 60)Sets the output frequency.
10Output voltage220V (10 220), 230V (10 230), 240V (10 240)Sets the output voltage.
11Maximum utility charging current2A to 140A (e.g., 11 140 for 140A)Sets the maximum charging current from the utility.
12Battery SOC point for switching to utility source (SBU mode)10% to 50% (Default: 50%)When SBU mode is selected, sets the battery SOC threshold for switching to utility.
13Battery SOC point for switching to battery mode (SBU mode)30% to 100% (Default: 95%)When SBU mode is selected, sets the battery SOC threshold for switching to battery.
16Charger source prioritySolar first (16 CSO), Solar and Utility (16 SNU), Only Solar (16 OSO)Configures the priority of charging sources.
18Alarm controlAlarm on (18 OON), Alarm off (18 OOF)Enables or disables audible alarms.
19Auto return to default display screenReturn to default (19 ESP), Stay at latest (19 HEP)Sets display behavior after inactivity.
20Backlight controlBacklight on (20 LON), Backlight off (20 LOF)Enables or disables LCD backlight.
22Beeps while primary source is interruptedAlarm on (22 AON), Alarm off (22 AOF)Enables or disables beeping when power source changes.
23Overload bypassBypass disable (23 BYd), Bypass enable (23 BYE)When enabled, unit transfers to line mode if overload occurs in battery mode.
25Record Fault codeRecord enable (25 FEN), Record disable (25 FdS)Enables or disables fault code recording.
26Bulk charging voltage (C.V voltage)Default: 56.4V. Range: 48.0V to 61.0V.Sets the bulk charging voltage. Increment of 0.1V.
27Floating charging voltageDefault: 54.0V. Range: 48.0V to 61.0V.Sets the floating charging voltage. Increment of 0.1V.
29Low DC cut-off voltageDefault: 40.0V. Range: 40.0V to 48.0V.Sets the low DC cut-off voltage. Increment of 0.1V. If LIB-485 is selected, this is the battery low SOC shutdown point (20%, range 5-30%).
30Battery equalizationEnable (30 EEn), Disable (30 EdS)Enables or disables battery equalization.
31Battery equalization voltageDefault: 58.4V. Range: 48.0V to 61.0V.Sets the battery equalization voltage. Increment of 0.1V.
33Battery equalized timeDefault: 60min. Range: 5min to 900min.Sets the duration of battery equalization. Increment of 5min.
34Battery equalized timeoutDefault: 120min. Range: 5min to 900min.Sets the timeout for battery equalization. Increment of 5min.
35Equalization intervalDefault: 30 days. Range: 0 to 90 days.Sets the interval between equalization cycles. Increment of 1 day.
36Equalization activated immediatelyEnable (36 AEn), Disable (36 AdS)Activates or cancels equalization immediately.
37GRID-tie operationOff grid (37 OFF), Hybrid (37 HYd)Sets inverter operation mode (off-grid or hybrid).
38GRID-tie current10A (38 10)Sets the GRID-tie current. Increment of 2A.
39Led pattern lightLed pattern off (39 LOF), Led pattern on (39 LON)Controls the LED pattern light.
41Dual outputDisable (41 L2F), Use (41 L20)Enables or disables the dual output function.
42Enter the dual output functional voltage pointDefault: 44.0V. Range: 40.0V to 52.0V.Sets the voltage point for dual output function. Increment of 0.1V.
43Lithium battery protocolPYLON (43 PYL), PACE (43 PAC)Selects the specific Lithium battery protocol.
44Delayed grid accessDisable (44 dIS), Enable (44 ENA)Enables or disables delayed grid access.
45Maximum Second Load20%~70%If dual output is enabled, the second channel output power can be changed to 20%~70% of rated power.

5.5 Display Setting

The LCD display information will be switched in turns by pressing “UP” or “DOWN" key. The selectable information is switched as below order: input voltage, input frequency, PV voltage, charging current, charging power, battery voltage, output voltage, output frequency, load percentage, load in Watt, load in VA, load in Watt, DC discharging current, main CPU Version.

5.6 Operating Mode Description

RGB Light (option)

  • Battery Mode: Red Light
  • Utility Mode: Blue Light
  • PV Mode: Purple Light

5.7 Battery Equalization Description

Equalization function is added into charge controller. It reverses the buildup of negative chemical effects like stratification, a condition where acid concentration is greater at the bottom of the battery than at the top. Equalization also helps to remove sulfate crystals that might have built up on the plates. If left unchecked, this condition, called sulfation, will reduce the overall capacity of the battery. Therefore, it's recommended to equalize battery periodically.

How to Apply Equalization Function

You must enable battery equalization function in monitoring LCD setting program 30 first. Then, you may apply this function in device by either one of following methods:

  1. Setting equalization interval in program 35.
  2. Active equalization immediately in program 36.

When to Equalize

In float stage, when the setting equalization interval (battery equalization cycle) is arrived, or equalization is active immediately, the controller will start to enter Equalize stage.

Equalize charging time and timeout

In Equalize stage, the controller will supply power to charge battery as much as possible until battery voltage raises to battery equalization voltage. Then, constant-voltage regulation is applied to maintain battery voltage at the battery equalization voltage. The battery will remain in the Equalize stage until setting battery equalized time is arrived. However, in Equalize stage, when battery equalized time is expired and battery voltage doesn't rise to battery equalization voltage point, the charge controller will extend the battery equalized time until battery voltage achieves battery equalization voltage. If battery voltage is still lower than battery equalization voltage when battery equalized timeout setting is over, the charge controller will stop equalization and return to float stage.

5.8 Mains and Lithium Battery Activation Function

  1. After 90s of mains power connection to the inverter, the machine is connected to the mains and starts to work.
  2. The inverter is in lithium battery mode (item 05 is LIP or LIL). After the mains is connected, the battery is not connected, and the mains activation function is automatically enabled.

6. Clearance and Maintenance for Anti-Dust Kit

6.1 Overview

Every inverter is already installed with an anti-dust kit from the factory. The inverter will automatically detect this kit and activate an internal thermal sensor to adjust the internal temperature. This kit also keeps dust from your inverter and increases product reliability in harsh environments.

6.2 Clearance and Maintenance

Step 1: Please loosen the screw in the counterclockwise direction on the top of the inverter.

Step 2: Then, the dustproof case can be removed, and the air filter foam can be taken out.

Step 3: Clean the air filter foam and dustproof case. After clearance, re-assemble the dust-kit back to the inverter.

NOTICE: The anti-dust kit should be cleaned from dust every one month.

7. Specifications

Table 1: Line Mode Specifications
INVERTER MODEL8.2KW10.2KW
Input Voltage WaveformPure Sine Wave (Utility or Generator)
Nominal Input Voltage230Vac
Low Loss Voltage170Vac±7V (UPS); 90Vac±7V (Appliances)
Low Loss Return Voltage180Vac±7V (UPS); 100Vac±7V (Appliances)
High Loss Voltage280Vac±7V
High Loss Return Voltage270Vac±7V
Max AC Input Voltage300Vac
Nominal Input Frequency50Hz / 60Hz (Auto detection)
Low Loss Frequency40±1Hz
Low Loss Return Frequency42±1Hz
High Loss Frequency65±1Hz
High Loss Return Frequency63±1Hz
Output Short Circuit ProtectionCircuit Breaker
Efficiency (Line Mode)>95% (Rated R load, battery full charged)
Transfer Time10ms typical (UPS); 20ms typical (Appliances)
Table 2: Inverter Mode Specifications
INVERTER MODEL8.2KW10.2KW
Rated Output Power8.2KW10.2KW
Output Voltage WaveformPure Sine Wave
Output Voltage Regulation230Vac±5%
Output Frequency50Hz/60Hz
Peak Efficiency0.93
Overload Protection3s@≥150% load; 5s@101%~150% load
Surge Capacity2* rated power for 5 seconds
Nominal DC Input Voltage48Vdc
Cold Start Voltage46.0Vdc
Low DC Warning Voltage @load < 50%44.0Vdc
Low DC Warning Voltage @load ≥ 50%42.0Vdc
Low DC Warning Return Voltage @load < 50%45.0Vdc
Low DC Warning Return Voltage @load ≥ 50%44.0Vdc
Low DC Cut-off Voltage @load < 50%41.0Vdc
Low DC Cut-off Voltage @load ≥ 50%40.0Vdc
High DC Recovery Voltage62Vdc
High DC Cut-off Voltage63Vdc
No Load Power Consumption70W75W
Table 3: Two Load Output Power
INVERTER MODEL8.2KW10.2KW
Full Load8200W10200W
Maximum Main Load8200W10200W
Maximum Second Load (battery model)2733W3400W
Main Load Cut Off Voltage44VDC
Main Load Return Voltage54VDC
Table 4: Charge Mode Specifications
INVERTER MODEL8.2KW10.2KW
Utility Charging Mode
Charging Algorithm3-Step
AC Charging Current (Max)140Amp140Amp
Bulk Charging Flooded Battery Voltage58.4
Bulk Charging AGM / Gel Battery Voltage56.4
Floating Charging Voltage54Vdc
MPPT Solar Charging Mode
Max. PV Array PowerPV1 Channel: 5400W, PV2 Channel: 5400WPV1 Channel: 5400W, PV2 Channel: 5400W
IMax.PVPV1 Channel: 18A, PV2 Channel: 18APV1 Channel: 18A, PV2 Channel: 18A
Nominal PV Voltage360Vdc
PV Array MPPT Voltage Range90Vdc~500Vdc
Max. PV Array Open Circuit Voltage500Vdc
Max Charging Current (AC charger plus solar charger)160Amp
Table 5: Grid-Tie Operation
INVERTER MODEL8.2KW10.2KW
Nominal Output Voltage220/230/240 VAC
Feed-in Grid Voltage Range195~253VAC
Feed-in Grid Frequency Range50±1Hz/60±1Hz
Nominal Output Current35.6A44.3A
Power Factor Range>0.99
Maximum Conversion Efficiency (DC/AC)98%
Table 6: General Specifications
INVERTER MODEL8.2KW10.2KW
Safety CertificationCE
Operating Temperature Range-10°C to 50°C
Storage temperature-15°C~60°C
Humidity5% to 95% Relative Humidity (Non-condensing)
Dimension (D*W*H), mm500*390*136mm
Net Weight, kg14.514.7
Table 9: Approximate Back-up Time Table
ModelLoad (W)Backup Time @ 48Vdc 100Ah (min)Backup Time @ 48Vdc 200Ah (min)
8.2KW/10.2KW5006131288
1000268613
1500158402
2000111271
250090215
320076182
350065141
400050112
450044100
50004090
62003680
72003270
82002860
92002450
102002040

Note:

  1. Backup time depends on the quality of the battery, age of battery and type of battery. Specifications of batteries may vary depending on different manufacturers.
  2. The final interpretation right of this product belongs to the company.

8. Troubleshooting

5.9 Fault Reference Code

Fault Reference Codes
Fault CodeFault EventIcon on
01Fan is locked when inverter is off.01 ERROR
02Over temperature02 ERROR
03Battery voltage is too high03 ERROR
04Battery voltage is too low04 ERROR
05Output short circuited or over temperature is detected by internal converter components.05 ERROR
06Output voltage is too high.06 ERROR
07Overload time out07 ERROR
08Bus voltage is too high08 ERROR
09Bus soft start failed09 ERROR
51Over current or surge51 ERROR
52Bus voltage is too low52 ERROR
53Inverter soft start failed53 ERROR
55Over DC voltage in AC output55 ERROR
57Current sensor failed57 ERROR
58Output voltage is too low58 ERROR
59PV voltage is over limitation59 ERROR
Battery Fault Codes (Lithium Battery Mode)
Fault codeFault eventFault condition
02The battery temperature is too high ProcedureLithium battery charging battery temperature ≥65°C; The discharge temperature of the lithium battery is higher than 70°C.
03The battery voltage is too high ProcedureLithium battery maximum single cell voltage >3.65V; Total voltage of lithium battery >54.6V (48V lithium battery).
04The battery voltage is too low ProcedureMinimum voltage of a lithium battery cell<2.71V; Lithium battery total voltage<40.4V (48V lithium battery).

5.10 Warning Indicator

Warning Indicators
Warning CodeWarning EventAudible AlarmIcon flashing
01Fan is locked when inverter is on.Beep three times every second01
03Battery is over-chargedBeep once every second03
04Low batteryBeep once every second04
07OverloadBeep once every 0.5 second07
10Output power deratingBeep twice every 3 seconds10
15PV energy is low.Beep twice every 3 seconds15
E9Battery equalizationNoneE9
6PBattery is not connectedNone6P
Battery Warning Codes (Lithium Battery Mode)
Warning codeWarning eventWarning condition
04The battery voltage is too lowMinimum voltage of a lithium battery cell<2.85V; Lithium battery total voltage<42V (48V lithium battery).
05The battery voltage is too highLithium battery maximum single cell voltage >3.55V; Total voltage of lithium battery >54V (48V lithium battery).
06The battery is low warningRemaining battery capacity ≤10%

Troubleshooting Table

Troubleshooting Guide
ProblemLCD/LED/BuzzerExplanation / Possible causeWhat to do
Unit shuts down automatically during startup process.LCD/LEDs and buzzer will be active for 3 seconds and then complete off.The battery voltage is too low (<1.91V/Cell)1. Re-charge battery. 2. Replace battery.
No response after power on.No indication.1. The battery voltage is far too low. (<1.4V/Cell) 2. Internal fuse tripped.1. Contact repair center for replacing the fuse. 2. Re-charge battery. 3. Replace battery.
Input voltage is displayed as 0 on the LCD and green LED is flashing.Input protector is trippedCheck if AC breaker is tripped and AC wiring is connected well.
Mains exist but the unit works in battery mode.Green LED is flashing.Insufficient quality of AC power. (Shore or Generator)1. Check if AC wires are too thin and/or too long. 2. Check if generator (if applied) is working well or if input voltage range setting is correct. (UPS/Appliances)
Green LED is flashing.Set "Solar First" as the priority of output source.Change output source priority to Utility first.
When the unit is turned on, internal relay is switched on and off repeatedly.LCD display and LEDs are flashingBattery is disconnected.Check if battery wires are connected well.
Fault code 07Overload error. The inverter is overload 110% and time is up.Reduce the connected load by switching off some equipment.
Fault code 05Output short circuited.Check if wiring is connected well and remove abnormal load.
Fault code 02Temperature of internal converter component is over 120°C. Internal temperature of inverter component is over 100°C.Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.
Buzzer beeps continuously and red LED is on.Fault code 03Battery is over-charged. The battery voltage is too high.Return to repair center. Check if spec and quantity of batteries are meet requirements.
Fault code 01Fan faultReplace the fan.
Fault code 06/58Output abnormal (Inverter voltage below than 190Vac or is higher than 260Vac)1. Reduce the connected load. 2. Return to repair center.
Fault code 08/09/53/57Internal components failed.Return to repair center.
Fault code 51Over current or surge.Restart the unit, if the error happens again, please return to repair center.
Fault code 52Bus voltage is too low.Restart the unit, if the error happens again, please return to repair center.
Fault code 55Output voltage is unbalanced.Restart the unit, if the error happens again, please return to repair center.

9. User Tips

  • Battery Compatibility: This inverter supports a wide range of battery types including Lifepo4, Lithium, Flooded, Gel, and Lead-acid Batteries. Ensure you select the correct battery type in the LCD settings (Program 05) for optimal performance and safety.
  • Smart Device Integration: The inverter is a smart device, offering WIFI and GPRS communication for monitoring via iOS and Android apps. Utilize these features for remote monitoring and control.
  • Output Frequency: The inverter supports both 50Hz and 60Hz output frequencies. Configure this setting (Program 09) to match your local grid requirements.
  • Geographic Applicability: This product is designed for use in various regions including Asia, Europe, Africa, and North America, supporting 220-240VAC drivers.
  • Single-Phase Operation: This inverter is a single-phase unit. It cannot be directly combined with other units to create a 3-phase (400V) application. For 3-phase systems, specialized inverters are required.
  • Wind Generator Compatibility: While the inverter supports general 'Generator' input, specific compatibility with wind generators may depend on the wind generator's output characteristics. Consult with a solar professional for integration with wind power systems.

10. Frequently Asked Questions (FAQ)

Q: Does it come with a built-in battery?
A: No, the inverter does not come with a built-in battery. It supports external 48V batteries (Lifepo4, Lithium, Flooded, Gel, Lead-acid). It does, however, have a built-in Lithium battery automatic activation feature.
Q: What's the maximum power this item can handle?
A: The rated output power of the 10.2KW model is 10200W.
Q: Is this item smart device compatible?
A: Yes, it is a smart device with WIFI & GPRS available for iOS and Android monitoring.
Q: What types of batteries does it support?
A: It supports Lifepo4, Lithium, Flooded, Gel, and Lead-acid Batteries.
Q: What are the available output frequencies?
A: The output frequency is configurable to either 50HZ or 60HZ.
Q: Where can I use this product?
A: It is applicable in Asia, Europe, Africa, and North America (with 220-240VAC drivers).

11. Warranty and Support

For technical support or warranty inquiries, please contact PowMr directly using the information below:

SHENZHEN HEHEJIN INDUSTRIAL CO.,LTD
Tel/Fax: +86 755-28219903
Email: support@powmr.com
Web: www.powmr.com
Address: Henggang Street, Longgang District, Shenzhen, Guangdong, China

For additional resources, including video guides, please visit the official PowMr Solar YouTube channel:

Unboxing and overview of the PowMr 10.2KW Hybrid Solar Inverter, including its components and key features. This video provides a visual guide to the product and its initial setup.

A PDF version of the user manual is also available for download: User manual (PDF)


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.