LILYGO T-Watch-S3

Contents

LILYGO® T-Watch-S3 User Manual

Model: T-Watch-S3

Brand: LILYGO

1. Introduction

The LILYGO® T-Watch-S3 is a versatile programmable wearable device designed for development and experimentation. It integrates an ESP32-S3 microcontroller, offering Wi-Fi and Bluetooth connectivity, along with LoRa communication capabilities. The watch features a 1.54-inch capacitive touch IPS LCD, a BMA423 3-axis acceleration sensor, MAX98357A audio amplifier, a PDM microphone, and a speaker, making it suitable for a wide range of applications from smart home control to IoT projects.

2. What's in the Box

  • 1 x LILYGO® T-Watch-S3 (with 470mAh battery)
  • 1 x Micro USB Charging Cable
LILYGO T-Watch-S3 and Micro USB charging cable
The T-Watch-S3 and its included Micro USB charging cable.

3. Specifications

T-Watch-S3 Key Specifications
FeatureDescription
MCUESP32-S3
Flash16MB
PS RAM8MB
PlatformArduino-IDE, ESP-IDF, VS Code, Micropython
WirelessWi-Fi: 802.11 b/g/n, Bluetooth: BLE V5.0
LoRa TransceiverSX1262 Low Power LoRa (Support 433MHz, 868MHz, 915MHz)
DisplayST7789V 1.54 inch Wide angle IPS LCD, 240x240 resolution, 16-bit full color, 220 ppi, Capacitive touch
SensorsBMA423 3-axis acceleration sensor
AudioMAX98357A Mic Speaker, PDM MIC (Data: IO47, Sclk: IO44)
Haptic MotorDRV2605 for ERM and LRA
Power ManagementAXP2101 Highly Integrated Power Management Unit
BatteryBuilt-in 400 mAh
InterfaceUSB Port & OTG
T-Watch-S3 Specifications table
Detailed specifications of the T-Watch-S3.
Product parameter comparison table for T-Watch series
Comparison of T-Watch series models and their parameters.

4. Setup Guide

4.1 Battery Activation

Before initial use, you may need to activate the built-in battery:

  1. Carefully open the back cover of the watch.
  2. Locate and remove the battery.
  3. Flip the battery switch to the 'ON' position.
  4. Reinsert the battery and close the back cover.
Battery installation steps: Open back cover, Remove battery, Flip switch ON
Steps to activate the T-Watch-S3 battery.

4.2 Charging the Device

To charge your T-Watch-S3, connect the provided Micro USB cable to the watch's USB port and a suitable power source (e.g., computer USB port, USB wall adapter).

T-Watch-S3 connected to charging cable
The T-Watch-S3 connected for charging.

5. Operating Instructions

5.1 Power On/Off

  • Power On: Press and hold the power button for 2 seconds.
  • Power Off: Press and hold the power button for 6 seconds.

5.2 Touch Screen Navigation

The T-Watch-S3 features a capacitive touch screen for intuitive interaction. Swipe left, right, up, or down to navigate through menus and applications. Tap to select items or confirm actions.

T-Watch-S3 displaying Radio Test menu
The T-Watch-S3 displaying the 'Radio Test' menu, demonstrating touch interaction.

5.3 LoRa Functionality

The T-Watch-S3 supports LoRa communication. Depending on the firmware loaded, you can access LoRa functions such as 'Radio Test' for transmitting (TX) and receiving (RX) data, and selecting operating frequencies (e.g., 433MHz, 868MHz, 915MHz).

5.4 Microphone and Speaker

The integrated PDM microphone and speaker allow for audio input and output, enabling applications such as voice commands, audio recording, or simple sound playback, depending on the programmed functionality.

A demonstration video showcasing the T-Watch-S3's features and touch interface.

6. Maintenance

  • Keep the device clean and dry. Avoid exposure to excessive moisture or extreme temperatures.
  • Use a soft, dry cloth to clean the screen and body.

Important Handling Notes:

  • The watch strap and body are designed for specific assembly. The watch cannot be pressed and pulled out in reverse from its casing.
  • The bottom case of the watch should not be removed during normal use, except for battery activation or specific maintenance as instructed.
  • Avoid forcing or buckling the four corners of the watch with your fingers, as this may cause damage.
Warning: Watch cannot be pressed and pulled out in reverse
Do not attempt to remove the watch from its casing by pressing and pulling in reverse.
Warning: Bottom case cannot be removed during use
The bottom case should remain attached during normal operation.
Warning: Do not force the corners of the watch
Avoid applying excessive force to the corners of the watch.

7. Troubleshooting

Q: The device does not power on.
A: Ensure the battery is properly activated (refer to Section 4.1) and fully charged. Connect the device to a power source using the Micro USB cable and try powering it on again.
Q: I cannot connect via Bluetooth.
A: Verify that the correct firmware is flashed to the device and that Bluetooth functionality is enabled in your custom code. Check your host device's Bluetooth settings and ensure it's in pairing mode. Refer to the official GitHub documentation for specific Bluetooth examples and troubleshooting.
Q: Does it work with Meshstatic?
A: Compatibility with specific third-party software like Meshstatic depends on the firmware loaded onto the T-Watch-S3. Please consult the official LILYGO GitHub repository or community forums for information regarding Meshstatic compatibility and relevant firmware.
Q: The screen is unresponsive or frozen.
A: Try performing a hard reset by holding the power button for 6 seconds to turn it off, then press it again for 2 seconds to restart. If the issue persists, ensure your firmware is stable and correctly configured for the touch display.

8. User Tips

  • Explore Firmware Options: The T-Watch-S3 is highly programmable. Visit the official LILYGO GitHub for various firmware examples and libraries to unlock its full potential.
  • MicroPython Support: For those preferring Python, MicroPython firmware for ESP32 is available. Refer to the MicroPython ESP32 Firmware Download link in the Support section for more details.
  • Community Engagement: For advanced projects or specific compatibility questions (e.g., with Meshstatic), engaging with the LILYGO developer community can provide valuable insights and solutions.

9. Important Notes

Based on factory firmware testing, with a battery voltage of 4.1V~4.2V, the screen is observed every 2 hours, displaying for approximately 15 seconds before automatically resting. The standby battery life is approximately 48 hours. Actual battery life may vary depending on usage patterns and loaded firmware.

10. Support & Resources

For further information, documentation, and community support, please refer to the following resources:

For customer service inquiries, please check your package and product upon receipt. If there are any issues, contact customer service for a satisfactory solution. If the package is damaged due to external force or transportation, provide clear pictures of the logistics label, carton/bag, and damaged product to receive a solution from the Logistics Service Provider. For customization or bulk orders, feel free to contact customer service.

Customer service contact information and notes
Notes for contacting customer service regarding product issues.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.