Introduction
Thank you for choosing the Heimerdinger LB113 Cordless Electric Spray Gun. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your new tool. Please read this manual thoroughly before first use and keep it for future reference.
Important Safety Instructions
Always follow basic safety precautions when using this product to reduce the risk of fire, electric shock, or personal injury.
- Wear appropriate personal protective equipment (PPE) such as safety glasses, gloves, and a respirator when spraying.
- Ensure the work area is well-ventilated.
- Keep children and pets away from the work area.
- Do not operate the spray gun near flammable liquids or gases.
- Always disconnect the battery before cleaning, maintenance, or when not in use.
- Do not point the spray gun at people or animals.
- Do not place the spray gun upside down to prevent the motor from being damaged by the backflow of paint. When spraying upwards, do not release the trigger, otherwise the paint will flow back into the motor and cause damage to the machine.
Package Contents
Depending on your purchased option, your package may contain the following items:
- 1 x Paint Sprayer Body
- 1 x User Manual
- 1 x Funnel
- 3 x Nozzles (1.0mm, 1.5mm, 2.0mm - 1.5mm usually pre-installed)
- Optional: 1 or 2 x 18V Lithium Battery (4.0Ah, 6.0Ah, or 9.0Ah)
- Optional: 1 x 18V Cable Charger

Setup and Assembly
- Attach the Spray Gun Head: Align the spray gun head with the main body and twist to secure it firmly.
- Insert the Battery: Ensure the battery is fully charged. Slide the 18V lithium battery into the base of the spray gun handle until it clicks into place. To remove, press the release button and slide the battery out.
- Select and Install Nozzle: The spray gun comes with 1.0mm, 1.5mm, and 2.0mm nozzles. The 1.5mm nozzle is typically pre-installed. Choose the appropriate nozzle for your paint and desired spray pattern. To change, unscrew the nozzle retaining ring, replace the nozzle, and re-secure the ring.
- Adjust Suction Tube: Rotate the suction tube to face the direction of the handle before use. This ensures proper paint flow depending on whether you are spraying upwards or downwards.
- Adjust Paint Viscosity: This is a critical step for optimal performance. Use the provided funnel to test the paint viscosity. The paint should flow through the funnel within the recommended time. If the paint is too thick, dilute it with the appropriate thinner as per the paint manufacturer's instructions. Refer to the 'Viscosity Funnel Reference Standard' table below.

Viscosity Funnel Reference Standard
| Paint Type | Viscosity (seconds) |
|---|---|
| Solvent-Based Primer | 20-40 s |
| Solvent-Based Paint | 15-40 s |
| Water-Based Primer | 25-40 s |
| Water-Based Paint | 20-35 s |
| Latex Paint | 30-40 s |
| Car Paint | 20-35 s |
| Wood Preservation, Gasoline, Oil, Disinfectant, Insecticide | No need to dilute |
- Fill Paint Storage Jug: Once the paint viscosity is correct, pour the paint into the 1000ml storage jug. Securely attach the jug to the spray gun.
Operating Instructions
- Power On: With the battery inserted and paint jug attached, press the trigger to start spraying.
- Adjust Spray Flow: Rotate the spray size adjustment knob (marked with '+' and '-') to control the paint flow rate.
- Adjust Spray Pattern: The nozzle allows for different spray patterns (horizontal, vertical, circular). Rotate the adjustable nozzle to achieve the desired pattern.
- Spraying Technique:
- Maintain a consistent distance of approximately 30-40 cm (12-16 inches) between the spray gun and the surface.
- Apply paint in two coats. The first coat should be thinner.
- Allow the first coat to dry completely before applying the second, thicker coat.
- Ensure the spray gun is not held upside down when spraying upwards, as this can cause paint backflow and damage the motor.


Applications
This cordless electric spray gun is suitable for a wide range of DIY and home improvement tasks, including:
- Indoor and outdoor wall spraying
- General home improvement spraying
- Spraying outdoor wooden railings
- Spraying iron materials

Maintenance and Cleaning
Proper cleaning and maintenance are crucial for prolonging the life of your spray gun and ensuring consistent performance.
- Immediate Cleaning: After each use, the spray gun must be cleaned immediately to prevent paint or other materials from drying and blocking the spray nozzle or internal components.
- Cleaning Method:
- Empty any remaining paint from the storage jug.
- Fill the watering can (paint storage jug) with clean water or an appropriate cleaning solution (compatible with your paint type).
- Spray the clean water/solution for approximately 30-60 seconds.
- Continue spraying until all residual dirt in the valve core is completely flushed out and only clean water is sprayed.
- Disassemble the nozzle and clean all parts thoroughly with water or cleaning solution.
- Wipe down the exterior of the spray gun with a damp cloth.
- Ensure all parts are dry before reassembling and storing.


Troubleshooting
If you encounter issues with your Heimerdinger LB113 spray gun, consider the following common solutions:
- No Spray/Weak Spray: Check paint viscosity. If too thick, dilute it. Ensure the nozzle is clean and not clogged. Verify the suction tube is correctly positioned.
- Uneven Spray Pattern: Check for clogged nozzle or air cap. Ensure the nozzle is securely tightened. Adjust the spray pattern setting.
- Paint Dripping: Ensure all connections are tight. Check for damaged seals or gaskets.
- Motor Not Starting: Ensure the battery is fully charged and properly inserted. Check for any obstructions in the trigger mechanism.
For persistent issues, please contact customer support.
Specifications
| Feature | Specification |
|---|---|
| Model Number | LB113 |
| Brand Name | heimerdinger |
| Power Type | Electric (Battery Powered) |
| Voltage | 18V DC |
| Load Power | 800W |
| No-Load Speed | 30000 RPM |
| Maximum Flow | 200 ml/min |
| Jet Flow | 0-1200 ml/min |
| Maximum Viscosity | 8-12 seconds |
| Cup Volume | 1000 ml |
| Nozzle Diameter | 1.0mm, 1.5mm, 2.0mm (3 nozzles included) |
| Feed Type | Pressure |
| Compatible Batteries | Makita 18V B series lithium battery (e.g., BL1850B, BL1840B, BL1830B, BL1820B), Heimerdinger 18V battery. NOT compatible with Makita G Series or 18V Ni-CD batteries. |
| Usage | Home DIY |
| Origin | Mainland China |

User Tips
- Always perform a test spray on a scrap piece of material to check the spray pattern and flow before applying to your main project.
- For best results, ensure your paint is thoroughly mixed and free of lumps before pouring it into the spray gun.
- When switching between different types of paint, ensure the spray gun is completely cleaned to prevent contamination and clogging.
- If you notice any decrease in spray quality, immediately check the nozzle for clogs and clean it.
Warranty and Support
For warranty information or technical support, please refer to the documentation provided with your purchase or contact the seller directly. Keep your proof of purchase for any warranty claims.