Autel MaxiTPMS TS508WF

Contents

Autel MaxiTPMS TS508WF TPMS Diagnostic & Service Tool User Manual

Model: MaxiTPMS TS508WF

Brand: Autel

1. Safety Information

For your own safety and the safety of others, and to prevent damage to the device and vehicles upon which it is used, it is important that the safety instructions herein presented throughout this manual be read and understood by all persons operating, or coming into contact with, the device.

There are various procedures, techniques, tools, and parts for servicing vehicles, as well as in the skill of the person doing the work. Because of the vast number of test applications and variations in the products that can be tested with this equipment, we cannot possibly anticipate or provide advice or safety messages to cover every circumstance. It is the automotive technician's responsibility to be knowledgeable of the system being tested. It is crucial to use proper service methods and test procedures. It is essential to perform tests in an appropriate and acceptable manner that does not endanger your safety, the safety of others in the work area, the device being used, or the vehicle being tested.

Before using the device, always refer to and follow the safety messages and applicable test procedures provided by the manufacturer of the vehicle or equipment being tested. Use the device only as described in this manual. Read, understand, and follow all safety messages and instructions in this manual.

Safety Messages

Safety messages are provided to help prevent personal injury and equipment damage. All safety messages are introduced by a signal word indicating the hazard level.

⚠️ DANGER

Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury to the operator or to bystanders.

⚠️ WARNING

Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury to the operator or to bystanders.

Safety Instructions

To prevent personal injury or damage to vehicles and/or the scan tool, read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle:

  • Always perform diagnosis or service in a safe environment.
  • Wear safety eye protection that meets ANSI standards.
  • Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
  • Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
  • Keep a fire extinguisher suitable for gasoline / chemical / electrical fires nearby.
  • Put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure the parking brake is engaged.
  • Always turn the ignition off before connecting/disconnecting the OBD II Cable to/from the TPMS tool; otherwise it may cause the Malfunction Indicator Light (MIL) to turn on.
  • Refer to the user's manual for the vehicle being serviced and adhere to all diagnostic procedures and precautions. Otherwise personal injury or unneeded repairs may result.
  • Keep the TPMS tool dry, clean, free from oil, water and grease. Use a mild detergent on a clean cloth to clean the outside of the TPMS tool when necessary.

2. Product Overview

The Autel MaxiTPMS TS508WF is a new generation TPMS diagnostic and service tool designed for comprehensive Tire Pressure Monitoring System (TPMS) maintenance. It features both Quick Mode and Advanced Mode options to streamline TPMS work, along with convenient Wi-Fi update capabilities.

Functional Description

Autel MaxiTPMS TS508WF device with key features highlighted
Figure 2-1: MaxiTPMS TS508WF Device Overview
  1. SENSOR SLOT: Holds the MX-Sensor to be programmed.
  2. LCD DISPLAY: Displays menus and test screens.
  3. N BUTTON: Cancels a selection (or action) from a menu or returns to the previous menu.
  4. UP SCROLL BUTTON: Moves up through menu and submenu items. Used to view previous screens for additional data or trouble codes.
  5. LEFT SCROLL BUTTON: Moves to previous character when scrolling text, or views additional information on previous screens.
  6. DOWN SCROLL BUTTON: Moves down through menu and submenu items. Used to view next screens for additional data or trouble codes.
  7. ? HELP BUTTON: Provides help information.
  8. POWER BUTTON: Long press to turn on/off the tool; short press to return to the Home screen.
  9. RIGHT SCROLL BUTTON: Moves to next character when scrolling text, or views additional information on next screens.
  10. TEST BUTTON: Commences a TPMS Test or confirms selections on screen.
  11. Y BUTTON: Confirms a selection (or action) from a menu.
  12. USB PORT: Connects the TPMS tool to a PC for software update, data printing, or battery charging.
  13. OBD II CONNECTOR: Connects the TPMS tool to the vehicle's Data Link Connector (DLC).

NOTE: Figures and illustrations, product characteristics, functions, and included accessories in this User Manual are provided for reference only and may differ from the actual product. Product design and specifications may be changed without notice.

3. Specifications

ItemDescription
DisplayTFT color display (320 x 240 dpi)
Power3.7 V Li-polymer battery
Operating Temperature-20°C to 70°C (-4°F to 158°F)
Storage Temperature-10°C to 45°C (14°F to 113°F)
Dimensions (LWH)215 mm (8.46") / 105 mm (4.13") / 37 mm (1.46")
Weight0.39 kg (0.86 lb.)
Wireless FunctionYes
Communication InterfaceOBD-II
Software UpdateYes (Free lifetime updates)
Wireless SupportWifi
Measurement Accuracy±0.3%
Is Batteries IncludedYes
MaterialPlastic
CertificationCE, FCC ID: WQ8MTPMS508WF
Supported SystemTPMS
Vehicle TypePassenger Vehicle

4. Accessories Included

Contents of the MaxiTPMS TS508WF package including the main unit, cables, adapter, and case.
Figure 4-1: MaxiTPMS TS508WF Package Contents
  • 1 x MaxiTPMS TS508WF Main Unit
  • 1 x OBD II Cable
  • 1 x USB Cable
  • 1 x AC Adapter
  • 1 x Carry Case
  • 1 x User Manual (PDF available for download)

5. Setup and Charging

Battery Charging

The TS508WF tool has a 3.7 V built-in lithium-ion polymer rechargeable battery. For optimum performance, always keep your tool sufficiently charged. It is recommended that you charge the tool for at least 2 hours before the first use.

To charge battery by USB cable via PC connection:

  1. Locate the USB port of the device.
  2. Connect the device and the computer with the USB cable.

To charge battery by USB cable adapter:

  1. Locate the USB port of the device.
  2. Connect the device and the power source with the USB cable adapter.

NOTE: Only use the USB cable adapter included in our pack to charge this tool. The use of unapproved power supplies may damage your tool and void the tool warranty.

The tool can also be powered by the vehicle via OBD II cable connection to the vehicle Data Link Connector (DLC). Just follow the steps below to turn on the TPMS tool:

  1. Connect the OBD II cable to the TPMS tool.
  2. Find the DLC on the vehicle.
  3. Connect the OBD II cable to the vehicle's DLC.
  4. Power up the TPMS tool by pressing the Power button, and wait for the Main Menu to display.

TIP: A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the OBD II cable.

NOTE: OBD II cable connection does not support battery charging.

6. Operating Instructions

Autel MaxiTPMS TS508WF showing the main menu with Quick Mode, Advanced Mode, and Toolkit options.
Figure 6-1: Main Menu Screen

TPMS Quick Mode

Perform basic TPMS functions through the Quick service mode. This mode is ideal for fast installs and basic checks.

Quick Mode features: Activate/Scan Sensor, Relearn Sensor, Sensor Information, Program Sensor.
Figure 6-2: Quick Mode Features

Vehicle Identification

Select the test vehicle to start a TPMS service session.

  1. From the Main Menu, select Quick Mode and press Y.
  2. Select Vehicle Type (e.g., Passenger Vehicle) and press Y.
  3. Select the vehicle's Make (e.g., Audi) and press Y.
  4. Select the vehicle's Model (e.g., A6 Allroad) and press Y.
  5. Select the vehicle's Year (e.g., 2011-2017) and press Y.

Scan Sensor

This function allows you to activate and read data from TPMS sensors.

  1. After vehicle identification, select Scan Sensor and press Y.
  2. Hold the tool close to the sensor (or close to the tire sidewall right above the sensor).
  3. Press Y or the Trigger button to activate the sensor.
  4. The device will display sensor data (ID, pressure, temperature, voltage) upon successful activation.
Image showing the TS508WF activating a sensor and displaying sensor data.
Figure 6-3: Activating and Reading Sensor Data

Program Sensor (MX-Sensor Only)

This function is used to program Autel MX-Sensors to replace faulty OE sensors.

  1. After vehicle identification, select Program Sensor and press Y.
  2. Choose a programming method:
    • Copy by Activation: Activates the original sensor and copies its ID to the MX-Sensor.
    • Copy by Manual Input: Manually enter the original sensor ID.
    • Auto Create 1-16 Sensors: Creates new unique IDs for up to 16 MX-Sensors.
    • Copy by OBD: Reads sensor IDs from the vehicle's ECU via OBD and copies them to MX-Sensors (available in Advanced Mode).
  3. Place the MX-Sensor(s) close to the top of the tool.
  4. Follow the on-screen instructions to complete programming.
Diagram illustrating the four MX-Sensor programming methods: Copy by OBD, Copy by Activation, Copy by Manual Input, Auto Create.
Figure 6-4: MX-Sensor Programming Methods

Relearn Procedure

A TPMS relearn is always required when a new TPMS sensor or sensors are installed to turn off the TPMS warning light.

  1. After vehicle identification, select Relearn Procedure and press Y.
  2. The tool will display the appropriate relearn procedure for the selected vehicle.
  3. Follow the on-screen instructions carefully to complete the relearn process.
Image showing three types of TPMS relearn: Stationary Relearn, OBD Relearn, and Automatic Relearn.
Figure 6-5: TPMS Relearn Methods

Sensor Information

This function allows you to view information about MX-Sensors and OE sensors.

  1. After vehicle identification, select Sensor Information and press Y.
  2. Choose between MX-Sensor Information or OE Sensor Information.
  3. For MX-Sensor, place the sensor near the top of the tool. For OE Sensor, the tool will automatically display information if available.
Image showing the TS508WF displaying OE and MX-Sensor information.
Figure 6-6: OE & MX-Sensor Information Display

TPMS Advanced Mode

The Advanced service mode performs additional TPMS functions: TPMS Diagnose, Program Sensor, Position Relearn, Information (OE and MX-Sensor data), and vehicle OBDII port location diagram. This mode is for comprehensive TPMS diagnostics and service.

Advanced Mode features: Support all Quick Mode features, Copy by OBD, OBD Location, Complete TPMS Diagnostic, Read/Erase DTCs, TPMS Light Reset, Read/Write Tire Type/Pressure.
Figure 6-7: Advanced Mode Features

TPMS Diagnose

This function is used to check TPMS and sensor status, read/clear DTCs, and reset the TPMS warning light.

  1. After vehicle identification, select TPMS Diagnose and press Y.
  2. If sensor activation is not performed, a guide will appear. Activate all sensors one by one.
  3. Connect the OBD cable to the vehicle's DLC.
  4. The tool will automatically read sensor IDs and Data Trouble Codes (DTCs) present in the ECU.
  5. The Sensor Status screen displays position, sensor ID, tire pressure, tire temperature, and battery level of the activated sensors.
  6. You can view DTCs detail description and erase DTCs if needed.
Image showing a car dashboard with a low tire pressure warning light and the TS508WF performing TPMS diagnostics.
Figure 6-8: TPMS Diagnostics in action

Tire Type/Pressure Selection

If all TPMS faults are cleared and tires are inflated to the placard reference pressure, but the TPMS MIL is still on, use this function to select tire type and set the correct pressure value.

  1. After vehicle identification, select Tire Type/Pressure Selection and press Y.
  2. Choose between Read Tire Type/Pressure or Write Tire Type/Pressure.
  3. Follow on-screen prompts to read or modify tire type and pressure settings.
Image showing the TS508WF displaying tire type and pressure information.
Figure 6-9: Read/Write Tire Type/Pressure

Toolkit Functions

The Toolkit provides additional utility functions.

  1. From the Main Menu, select Toolkit and press Y.
  2. Select RKE & RF Monitor to test the strength of a remoteless key fob signal. Hold the key fob close to the tool and press its function buttons.
  3. Select Unlock ECU (just support Toyota) to unlock the ECU for supported Toyota vehicles.
Image showing the TS508WF testing a key fob signal strength.
Figure 6-10: Toolkit Functions - Key Fob Check

7. Maintenance

Cleaning the Tool

Keep the TPMS tool dry, clean, free from oil, water, and grease. Use a mild nonabrasive detergent and a soft cotton cloth to clean the keypad and display. No solvents such as alcohol are allowed for device cleaning. Do not soak the keypad as the keypad is not waterproof.Software Updates

The TS508WF offers lifetime free updates to support the newest car models and features. Regular updates ensure optimal performance and compatibility.

Video 7-1: Demonstrates the Wi-Fi update process for the Autel MaxiTPMS TS508WF.

Update by Wi-Fi

The Wi-Fi update function allows you to update the scan tool software directly without a computer.

  1. From the Main Menu, select My Device and press Y.
  2. Choose Update by Wi-Fi.
  3. Select Scan Wi-Fi to find available networks, then select your network and sign in.
  4. Keep the tool connected to a power source during the entire update process to ensure successful installation.
  5. The device will restart automatically after the update is successful.
Image showing the TS508WF connected to Wi-Fi for updates.
Figure 7-2: Wi-Fi Update Process

Update by USB with the Maxi PC Suite

This method requires a Windows-based computer and the Maxi PC Suite software.

  1. Download the Maxi PC Suite from www.maxitpms.com > Product > MaxiTPMS TS508WF > Downloads, and install it onto your Windows-based computer.
  2. Connect the tool to the computer using the supplied USB cable.
  3. Run the Maxi PC Suite on the computer.
  4. Select Update by USB on the tool's My Device Menu to enter Update Mode.
  5. The Maxi PC Suite will automatically detect the device. If not registered, follow the on-screen prompts to register using your email.
  6. Select the appropriate files to install from the 'Updates Available' page.
  7. The tool will restart automatically after the update is successful.
Image showing the TS508WF connected via USB to a computer for updates.
Figure 7-3: USB Update Process

Settings

The tool allows you to make the following adjustments and settings:

  • Market: Selects the operating region of the tool.
  • Language: Selects the operating language of the tool (English, Spanish, French, German, Russian, Italian, Japanese, Korean, Dutch, Polish, Portuguese, Swedish, etc.).
  • ID Format: Sets the ID display to Hexadecimal, Decimal, or Auto.
  • Pressure Unit: Sets the pressure unit in kPa, Psi, or Bar.
  • Temperature Unit: Sets the temperature unit in degrees to Celsius or Fahrenheit.
  • Distance Unit: Sets the distance unit in km or mile.
  • Beep Set: Turns on/off key-press beep.
  • Power-off: Sets the amount of time of inactivity before the tool automatically powers off.
  • Date and Time: Sets date and time on the tool.

TIP: The default market selection depends on the area the tool is sold. English is the default language. If you need another language, you may need to provide the device's serial number for authorization and update via PC Suite.

8. Troubleshooting

Vehicle Linking Error

A communication error occurs if the TPMS tool fails to communicate with the vehicle's ECU (Electronic Control Unit) when running the diagnostic function. You need to do the following to check:

  • Verify that the ignition is ON.
  • Check if the TPMS tool's OBD II connector is securely connected to the vehicle's DLC.
  • Verify that the vehicle is OBD II compliant.
  • Verify that the vehicle is equipped with TPMS.
  • Verify that the tool battery is sufficiently charged.
  • Turn the ignition off and wait for about 10 seconds. Turn the ignition back on and continue testing.
  • Verify the control module is not defective.

Operating Error

If the scan tool freezes, reset the tool:

  • Turn the ignition off and wait for about 10 seconds. Turn the ignition back on and continue testing.

9. User Tips

  • Language Setup: If your desired language (e.g., Russian, Dutch) is not immediately available after the first Wi-Fi update, you might need to connect the device to a computer, install the Autel PC Suite, and perform an update through the software. This often resolves language pack issues.
  • Customs Fees: Be aware that depending on your region, additional customs fees might apply upon receipt of the product.
  • Prompt Seller Support: If you encounter issues, especially with language or firmware, contact the seller. Many users report quick and helpful responses for resolving such problems.
  • Battery Life: The device has a built-in battery, making it portable for use in the garage or on the go.

10. Compliance Information

FCC Compliance

FCC ID: WQ8MTPMS508WF

This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

RF Warning Statement

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

RoHS Compliance

This device is declared to be in compliance with the European RoHS Directive 2011/65/EU.

CE Compliance

This product is declared to conform to the essential requirements of the following Directives and carries the CE mark accordingly:

  • EMC Directive 2014/30/EU
  • R&TTE Directive 1999/5/EC
  • Low Voltage Directive 2014/35/EU

11. Warranty and Support

Limited One Year Warranty

Autel Intelligent Technology Corp., Ltd. (the Company) warrants to the original retail purchaser of this MaxiTPMS Diagnostic Device that should this product or any part thereof during normal usage and under normal conditions be proven defective in material or workmanship that results in product failure within a 1-year period from the date of purchase, such defect(s) will be repaired, or replaced (with new or rebuilt parts) with Proof of Purchase, at the Company's option, without charge for parts or labor directly related to the defect(s).

NOTE: If the warranty period is inconsistent with local laws and regulations, please comply with the relevant local laws and regulations.

The Company shall not be liable for any incidental or consequential damages arising from the use, misuse, or mounting of the device. Some states do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you.

This warranty does not apply to:

  1. Products subjected to abnormal use or conditions, accident, mishandling, neglect, unauthorized alteration, misuse, improper installation or repair or improper storage;
  2. Products whose mechanical serial number or electronic serial number has been removed, altered or defaced;
  3. Damage from exposure to excessive temperatures or extreme environmental conditions;
  4. Damage resulting from connection to, or use of any accessory or other product not approved or authorized by the Company;
  5. Defects in appearance, cosmetic, decorative or structural items such as framing and non-operative parts.
  6. Products damaged from external causes such as fire, dirt, sand, battery leakage, blown fuse, theft or improper usage of any electrical source.

IMPORTANT: All contents of the product may be deleted during the process of repair. You should create a back-up copy of any contents of your product before delivering the product for warranty service.

Service and Support

If you have any questions regarding the product, please contact one of our offices in your region:

Autel North America

  • Phone: 1-855-288-3587 (Monday-Friday 9AM-6PM Eastern Time)
  • Website: www.autel.com/us
  • Email: ussupport@autel.com
  • Address: 36 Harbor Park Drive, Port Washington, New York, USA 11050

Autel Europe

  • Phone: +49(0)89 540299608 (Monday-Friday, 9AM-6PM Berlin Time)
  • Website: www.autel.eu
  • Email: support.eu@autel.com
  • Address: Landsberger Str. 408, 81241 München, Germany

Autel China HQ

  • Phone: +86 (0755) 8614-7779 (Monday-Friday, 9AM-6PM Beijing Time)
  • Website: www.autel.com, www.maxitpms.com
  • Email: supporttpms@auteltech.com
  • Address: Floor 2, Caihong Keji Building, 36 Hi-tech North Six Road, Songpingshan Community, Xili Sub-district, Nanshan District, Shenzhen City, China

Autel APAC (Japan)

  • Phone: +81-045-548-6282
  • Website: www.autel.com/jp
  • Email: support.jp@autel.com
  • Address: 6th Floor, Ari-nadoribiru 3-7-7, Shinyokohama, Kohoku-ku, Yokohama-shi, Kanagawa-ken, 222-0033 Japan

Autel APAC (Australia)

Autel IMEA

Autel Latin America (Mexico)

  • Phone: +52 33 1001 7880 (Spanish in Mexico)
  • Email: latsupport@autel.com
  • Address: Avenida Americas 1905, 6B, Colonia Aldrete, Guadalajara, Jalisco, Mexico

Autel Latin America (Brazil)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.