FGHGF Midea i5 / i5 Young / i5 Extra / i5 Blink

Contents

FGHGF Replacement Motherboard for Midea i5 Series Robotic Vacuum Cleaners

Models: Midea i5, i5 Young, i5 Extra, i5 Blink

Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of the FGHGF replacement motherboard designed for Midea i5, i5 Young, i5 Extra, and i5 Blink robotic vacuum cleaners. Please read this manual thoroughly before proceeding with installation to ensure proper functionality and safety.

Safety Information

  • Always disconnect the robotic vacuum cleaner from its power source and remove the battery before attempting any installation or maintenance.
  • Wear anti-static gloves or use an anti-static wrist strap to prevent electrostatic discharge (ESD) damage to electronic components.
  • Handle the motherboard by its edges to avoid touching sensitive components.
  • Keep small parts away from children.

Installation Guide

This replacement motherboard is intended for users with basic technical knowledge and experience in disassembling and reassembling electronic devices. If you are unsure, please seek professional assistance.

Required Tools:

  • Small Phillips head screwdriver
  • Pry tool (plastic)
  • Anti-static mat or wrist strap (recommended)

Installation Steps:

  1. Prepare the Vacuum Cleaner: Ensure the robotic vacuum cleaner is powered off and disconnected from its charging base. Remove the battery pack.
  2. Disassemble the Vacuum Cleaner: Carefully remove the bottom cover and any other necessary components to access the existing motherboard. Refer to your specific Midea i5 series vacuum cleaner's service manual or online guides for detailed disassembly instructions.
  3. Locate and Disconnect Old Motherboard: Identify the old motherboard. Gently disconnect all ribbon cables, wire connectors, and screws securing the motherboard in place. Take photos of the connections before disconnecting to aid reassembly.
  4. Remove Old Motherboard: Once all connections and screws are removed, carefully lift out the old motherboard.
  5. Install New Motherboard: Place the new FGHGF replacement motherboard into the vacuum cleaner's chassis, aligning it with the screw posts.
  6. Connect Cables: Reconnect all ribbon cables and wire connectors to their corresponding ports on the new motherboard. Ensure all connections are secure and correctly oriented. Refer to your previously taken photos if needed.
Front view of the FGHGF replacement motherboard for Midea i5 series robotic vacuum cleaners, showing various chips and connectors.
Figure 1: Front view of the FGHGF replacement motherboard.
Back view of the FGHGF replacement motherboard, displaying circuit traces and solder points.
Figure 2: Back view of the FGHGF replacement motherboard.
  1. Secure Motherboard: Fasten the motherboard with the appropriate screws. Do not overtighten.
  2. Reassemble Vacuum Cleaner: Reattach all removed components and the bottom cover. Ensure all parts fit snugly.
  3. Test Functionality: Reinstall the battery, place the vacuum cleaner on its charging base, and power it on. Verify that the vacuum cleaner operates correctly.

Operation

The FGHGF replacement motherboard restores the core functionality of your Midea i5 series robotic vacuum cleaner. Once correctly installed, the vacuum cleaner should operate as intended by its original design.

For specific operating instructions, such as scheduling, cleaning modes, and app connectivity, please refer to the original user manual provided with your Midea i5, i5 Young, i5 Extra, or i5 Blink robotic vacuum cleaner.

Maintenance

The motherboard itself requires no routine maintenance. However, to ensure the longevity and optimal performance of your robotic vacuum cleaner after motherboard replacement, follow these general guidelines:

  • Keep the vacuum cleaner clean and free of dust and debris, especially around vents and charging contacts.
  • Avoid exposing the vacuum cleaner to liquids or excessive moisture.
  • Do not drop or subject the vacuum cleaner to strong impacts.
  • Regularly clean or replace filters, brushes, and other consumable parts as recommended in your vacuum cleaner's original manual.

Troubleshooting

If your Midea i5 series robotic vacuum cleaner does not function correctly after installing the new motherboard, consider the following troubleshooting steps:

  • No Power/Not Turning On:
    • Ensure the battery is properly installed and charged.
    • Verify all power connectors to the motherboard are securely attached.
    • Check the power button and its connection to the motherboard.
  • Partial Functionality/Errors:
    • Re-open the vacuum cleaner and carefully inspect all ribbon cables and wire connectors for proper seating and orientation. A loose or incorrectly connected cable can cause specific functions to fail.
    • Ensure no debris or foreign objects are obstructing internal components.
  • Compatibility Issues:
    • Double-check that your vacuum cleaner model (Midea i5, i5 Young, i5 Extra, or i5 Blink) is explicitly listed as compatible with this motherboard.
  • Persistent Problems:
    • If issues persist after re-checking all connections and compatibility, consider reinstalling the original motherboard (if available) to determine if the problem lies with the new replacement part or another component of the vacuum cleaner.

For further troubleshooting specific to your vacuum cleaner's error codes or behaviors, consult its original user manual.

Specifications

FeatureDetail
Product TypeVacuum Cleaner Main Board Replacement
BrandFGHGF
Compatible ModelsMidea i5, Midea i5 Young, Midea i5 Extra, Midea i5 Blink Robotic Vacuum Cleaners
MaterialMetal
Part Type CategoryBRUSHES (Note: This is a generic category; the product is a motherboard.)
OriginMainland China
Package Dimensions (approx.)Length: 20 cm, Width: 17 cm, Height: 17 cm
Package Weight (approx.)0.2 kg
Package Contents1x Motherboard

User Tips

  • Verify Compatibility: Always verify the exact model number of your Midea robotic vacuum cleaner (i5, i5 Young, i5 Extra, i5 Blink) to ensure compatibility before purchasing and installing this replacement motherboard. This motherboard is not compatible with Midea VCR15 models.
  • Document Disassembly: Take clear photos or videos during the disassembly process, especially of cable connections, to serve as a reference during reassembly.

Warranty and Support

For any questions regarding the FGHGF replacement motherboard, including installation assistance or warranty claims, please contact the seller directly through the platform where the purchase was made. Provide your order number and a detailed description of the issue for prompt support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.