1. Introduction
The ESCAM K716 is a high-performance 16-channel Network Video Recorder (NVR) designed for advanced IP camera surveillance systems. It supports up to 5MP resolution cameras and utilizes H.265 compression for efficient storage. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your K716 NVR.
2. Setup Guide
2.1 Package Contents
Ensure all components are present:
- ESCAM K716 NVR Unit
- Power Adapter (12V 2A)
- USB Mouse
- Quick Start Guide (if included)
2.2 Hard Drive Installation (Optional)
The NVR supports one SATA Hard Disk Drive (HDD) up to 8TB. An HDD is required for recording video footage and is not typically included with the NVR unit.
- Unscrew the top cover of the NVR chassis.
- Connect the SATA data cable and power cable to the HDD.
- Secure the HDD to the NVR chassis using the provided screws.
- Replace the top cover and secure it with screws.
- Upon first power-on, you may need to format the HDD through the NVR's system settings.
2.3 Physical Connections
Refer to the rear panel diagram and connection illustration for proper wiring.
- Power: Connect the 12V 2A power adapter to the DC 12V input port.
- Network (LAN): Connect an Ethernet cable from your router/switch to the RJ45 LAN port for network access and IP camera communication.
- Display: Connect a monitor to either the HDMI (HD-Out) or VGA port for local video output. The HDMI port supports audio output.
- USB: Connect the included USB mouse to one of the two USB 2.0 ports for system navigation. You can also use these ports for USB flash drives for backup.
- IP Cameras: Connect your IP cameras to the same network as the NVR. The NVR supports 16 channels of 5MP IP network cameras and is ONVIF compatible.
3. Operation
3.1 Initial Power-On and System Access
After connecting all necessary cables, power on the NVR. The system will boot up, and you should see the interface on your connected monitor. Follow the on-screen prompts for initial setup, including setting up an administrator password and network configuration (DHCP is supported for automatic IP address assignment).
3.2 Live View and Playback
The NVR supports live preview with various screen split options (1/4/9 screens). You can view up to 16 channels simultaneously. For playback, the system supports adaptive stream preview and playback, allowing for detailed review of recorded footage.
3.3 Smart Analysis Functions
When paired with compatible Smart IPC cameras using the SLINK protocol, the NVR can perform advanced smart analysis functions, including:
- Target Count: Counts objects or people passing through a defined area.
- Object Left/Lost: Detects if an object has been left behind or removed from a specific zone.
- Area Detection: Triggers an alert when motion is detected within a designated area.
- Line Crossing: Triggers an alert when an object crosses a predefined virtual line.
3.4 H.265 Compression
The NVR utilizes H.265 and H.265+ video compression technologies, which provide clearer image quality at a lower bit rate. This significantly reduces transmission bandwidth and storage costs, saving up to 50% more storage space compared to H.264 compression.
3.5 Remote Monitoring (AEeye)
The ESCAM K716 NVR supports P2P remote monitoring via the AEeye application. This allows you to access your surveillance system from various devices:
- Mobile Devices: iPhone, iPad, Android smartphones.
- Computer Clients: Windows 7 and above, Apple MAC computers.
Ensure your NVR is connected to the internet and configured for P2P access through its network settings.
4. Maintenance
4.1 Hard Drive Management
Regularly check the status of your installed Hard Disk Drive (HDD) through the NVR's system settings. Ensure there is sufficient storage space. The NVR supports backup to USB flash drives for important footage.
4.2 Environmental Conditions
To ensure optimal performance and longevity, operate the NVR within the specified environmental conditions:
- Working Temperature: -10℃ to +55℃
- Working Humidity: 10％-90％
Avoid exposing the NVR to extreme temperatures, high humidity, or direct sunlight.
4.3 Power Considerations
Use only the provided 12V 2A power adapter. Ensure a stable power supply to prevent unexpected shutdowns, which can lead to data loss or system corruption.
5. Troubleshooting
5.1 No Display on Monitor
- Check if the NVR is powered on and the power adapter is securely connected.
- Verify that the HDMI or VGA cable is properly connected to both the NVR and the monitor.
- Ensure the monitor is set to the correct input source (HDMI/VGA).
- Try a different monitor or cable to rule out display issues.
5.2 Network Connectivity Issues
- Check if the Ethernet cable is securely connected to the NVR's LAN port and your router/switch.
- Verify that your router/switch is functioning correctly and has internet access.
- Ensure the NVR's network settings (IP address, gateway, DNS) are correctly configured. If using DHCP, ensure your router is assigning IP addresses.
- Restart the NVR and your network equipment.
5.3 IP Camera Not Detected
- Ensure the IP camera is powered on and connected to the same network as the NVR.
- Verify the camera's IP address and ensure it's not conflicting with other devices.
- Check if the camera is ONVIF compliant and its ONVIF settings are enabled.
- Use the NVR's camera search function to find and add cameras.
- Ensure the camera's firmware is up to date.
5.4 Recording Issues
- Verify that a Hard Disk Drive (HDD) is installed and properly formatted.
- Check the HDD status in the NVR's system settings to ensure it's healthy and has sufficient free space.
- Ensure recording schedules are correctly configured for your cameras.
- Check camera connections and ensure they are actively streaming video.
6. Specifications
| Feature Category | Feature | Specification |
|---|---|---|
| General | Model Number | K716 |
| Operating System | Embedded LINUX operating system | |
| Video Standard | H.265+/ H.265/H.264 | |
| Smart Analysis | With Smart IPC support | Target Count, Object Left /Lost, Area Detection, Line Crossing |
| Video & Audio Input | Video Input | 16CH 5MP IP Network Cameras |
| Audio Input | IPC composite stream network audio input | |
| Video & Audio Output | HDMI Output | 1CH, HDMI can output audio at the same time |
| VGA Output | 1CH | |
| Preview Split | 1/4/9 screen | |
| Video & Audio Codec | Video Resolution | 5MP and below resolution |
| Synchronized Playback | Support adaptive stream preview and playback: 9 screens D1, 4 screens 1280*720, single screen 2560*1920 | |
| External Ports | Internet | 1 x RJ45 10M/100M/1000M adaptive Ethernet port |
| USB | 2 x USB2.0 rear | |
| HDD | HDD Port | 1 x SATA HDD Port |
| MAX Capacity | up to 8TB | |
| POE | Interface | None |
| Support Standard | None | |
| Network Management | Network Protocol | UPnP (Plug & Play), SNMP (Simple Network Management), NTP (Network Timekeeping), SADP (Device Network Search), SMTP (Mail Service), NFS (Access NAS), iSCSI (IP SAN Application), PPPoE (Dial-up Internet access), DHCP (automatically obtain IP address) |
| P2P Remote Monitoring | AEeye Compatibility | Supports iPhone, iPad, Android Smart phone, Windows 7 and above computer client, Apple MAC computer client |
| IP Mode | Static IP address | |
| Physical & Environmental | Power Supply | 12V 2A |
| Working Temperature | -10℃ to +55℃ | |
| Working Humidity | 10％-90％ | |
| Power Consumption | NVR motherboard function ≤25W (Without HDD) | |
| Dimensions (Device) | 255mm × 220mm × 43mm | |
| Weight (Without HDD) | 0.63Kg | |
| Installation Method | Desktop installation |
7. User Tips
- Hard Drive: Remember that the NVR does not come with a pre-installed hard drive. You will need to purchase and install a SATA HDD (up to 8TB) separately for video recording.
- Network Setup: For easiest setup, ensure your network router has DHCP enabled. This will automatically assign an IP address to the NVR.
- Camera Compatibility: While the NVR supports ONVIF, ensure your IP cameras are fully compatible for best performance and access to all features.
8. Warranty and Support
ESCAM strives for 100% customer satisfaction. If you encounter any issues or have questions regarding your K716 NVR, please contact the seller or manufacturer's support channel immediately. Providing detailed information about your issue will help expedite the resolution process.
