Skydroid T10

Contents

Skydroid T10 Remote Control with Mini Camera User Manual

Model: T10 | Brand: Skydroid

Safety Warnings

WARNING: Misuse of this product may result in injury, damage or loss of property. Read the manual carefully before using this product. This item is not a toy. This item is intended for use by professional UAV operators and installers only. Do not use this product if you lack the knowledge and expertise to install and maintain UAV radio equipment. DO NOT use unapproved or unofficial components with this system. Operators must strictly follow the operation guides set forth in this manual. Skydroid does not accept any liability for the use or misuse of this product.

General Safety Precautions

  • DO NOT fly under the influence of substances, or when tired!
  • DO NOT fly in strong wind and/or rainy conditions!
  • DO NOT fly close to electric emission towers, communication stations, and crowded areas!
  • DO NOT fly nearby airports and other prohibited areas!
  • DO NOT fly around people or animals, or in any location where possible to damage property.
  • Check equipment before every flight and carry out maintenance and repairs as needed.
  • Use certified chargers to charge the batteries.
  • DO NOT put unnecessary force on antennas or electronic components to avoid damage.

Product Overview

The Skydroid T10 Remote Control system is designed for professional UAV operators and installers, offering advanced control and digital transmission capabilities.

Key Features

  • Dual antenna plus dual RF module with integrated control algorithms for reliable communication via full angle high gain antennas. Uses FHSS (Frequency Hopping Spread Spectrum) technology.
  • Integrated digital video transmission, up to 10KM range.
  • Integrated data transmission, up to 20KM range.
  • Parameter adjustments via APP with upgraded traditional OSD to touch panel control.
  • Connectivity via Bluetooth or USB, supporting S.BUS, PPM, PWM, Serial ports, and external devices.
  • APP connectivity via Bluetooth allows switching operation models, adjusting data (forward/reverse, rudder volume, channel binding), runaway protection value, SBUS, PPM output, and digital baud rate. Includes parameter saving and loading functions.
  • Based on the “Tower” APP for optimal compatibility with Pixhawk systems, offering large map view for easy waypoint selection and route planning, including one-key return to home. Also supports Tower, QGC, JIYI, TOPXGUN, and BOYING APP.
  • Uses two 18650 batteries (not included) for over 20 hours endurance with 20DBm transmission frequency.
  • Highly integrated datalink with video & data transmission and telemetry in one unit. Ultra-small size, with folding brackets, strong and stable.
  • Supports various optional cameras: mini digital camera, digital camera with LED, 20 times zoom camera, etc.

Main Application and Usage

Specially designed for UAV, Helicopter, Fixed Wing, Multi Rotor, or Boat operation. Used for video transmission (with optional camera), data link, and control of UAV.

Skydroid T10 Remote Control with tablet, R10 receiver, and mini camera/gimbal options
Skydroid T10 Remote Control system with various components.
Skydroid T10 Remote Control and included accessories
Skydroid T10 Remote Control and accessories.

Specifications

Controller Data (T10 Transmitter)

AttributeValueAttributeValue
ModelT10Channels10
Working Voltage4.2VWorking Current100mA
Frequency2.400-2.483GHzModulationNew FHSS
FirmwareAPP onlineWeight525g
Dimension160*150*50mmBattery Capacity4000mA
Duration20 HoursCharge PortMICRO-USB
ApplicationHelicopter, Fixed wing, Quadcopter, Car, Boat

Receiver Data (R10)

AttributeValueAttributeValue
ModelR10Channels10
Working Voltage4.5-5.5VWorking Current100mA
Dimension50*31*12mmWeight20g

MINI Camera Specifications (MINIDCAM)

AttributeValueAttributeValue
ModelMINIDCAMSize30*29*26mm
Working Current180mAWeight15.6g

Product Package Information

AttributeValue
Package Length35 cm
Package Width23 cm
Package Height13 cm
Package Weight1.016 kg

Setup

1. Pre-Check and Preparation

ATTENTION

  1. Check T10 battery level.
  2. Check position of the antenna to get better performance.
  3. Make sure the firmware is the latest version.
  4. DO NOT operate under the influence of alcohol or drug.

2. T10 Controller Layout

Skydroid T10 Controller diagram with numbered parts
Skydroid T10 Controller with labeled components.
NumberDescriptionNumberDescription
12.4G 3dB Antenna8Power on/off button
2USB1/video output9Button B
3Three lever switch E10Right joystick X2, Y2
4Jog wheel C11Jog wheel D
5Left joystick X1, Y112Three lever switch F
6Battery indicator13Charging/data transmission
7Button A

Battery Level LED Definition

LED StatusBattery Level
All 4 LEDs on75%-100%
3 LEDs on50%-75%
2 LEDs on25%-50%
1 LED on0%-25%

Antenna Positioning

Correct antenna positioning is crucial for optimal performance and range.

Skydroid T10 Remote Control with antennas upright
Correct antenna position: Upright the antenna on the T10 controller.
UAV with correctly positioned antennas, far from central board and upright
UAV Correct antenna position: Place far from central board, upright the antenna without any obstacle.
UAV with correctly positioned antennas, under the drone arm
UAV Correct antenna position: Place under the drone arm.

Incorrect Antenna Placement

  • UAV with antenna placed inside the board
    DO NOT put antenna inside of the board.
  • UAV with antenna placed close to carbon fiber or metal parts
    DO NOT place antenna close to Carbon Fiber or Metal parts.
  • UAV with antenna crossing the central flight control board and container
    DO NOT cross the antenna between the central Flight control board and container.

Operating Instructions

Part 1: Connect Device Helper

  1. Confirm receiver and flight controller are ready, power up to make sure the receiver is running normally.
  2. Only supports Android system.
  3. Install APP (download from official website www.skydroid.xin: Device Helper).
  4. Turn on the T10 (short press + long time press), turn on Bluetooth on the phone and search. Find: T10-XXX, select and enter the pairing code 1234, then the connection is successful.
  5. Adjust parameters: enter controller interface. APP reads the current data of controller and receiver.
Device Helper app interface showing parameter adjustment options
Device Helper app interface for parameter adjustment.
Device Helper app interface showing channel settings
Device Helper app interface for channel settings.

Attention:

  1. Please select the value between 900-2100, Failsafe hold select “0”.
  2. Please click SAVE at the right upper corner to keep the record. The selected value will be written to the controller and receiver.

Saving and Downloading Data

To quickly change between models or for large-scale setups, you can save data in the APP. After adjustment, click the save icon, rename the model, and save it. This is similar to downloading data.

Attention: Adjusted parameters are only saved in the APP. Click “write” to load data to the controller. A “Di” sound indicates successful communication.

Device Helper app interface showing save configuration options
Device Helper app interface for saving configuration.

Part 2: Receiver, Flight Controller Connection and Setup

  1. Binding: Press and hold the pairing button on the side of the receiver for 2 seconds until the green light flashes quickly, indicating pairing mode. Turn on the main unit; successful pairing is indicated by a solid green light.
  2. Data Link Pin: Use the attached wire or a DIY connector to connect the receiver's Tx pin to the Flight control board's Rx pin.

Part 3: T10 Connect to Android Phone

  1. Connect the receiver and camera (e.g., mini digital camera). Power up the system.
  2. Download Skydroid FPV from www.skydroid.xin.
  3. Use Bluetooth to connect the T10 and the display.
  4. Click "Yes" to confirm, and the image will show on your phone.
  5. For more details on Skydroid FPV usage, refer to the official website.

Part 4: How T10 Connect to PC Mission Planner, QGC

  1. Use two USB connectors to link between USB1 and a USB port on the PC. Select the port related to the ground station. Set Baud Rate to 115200 to link with the data port of the flight controller. (QGC and Mission Planner require SDK of Skydroid to show images, currently under development).
  2. Use a Micro data cable to connect USB2 and the PC. Set Baud Rate to 57600 (only supports data, not video).

Part 5: How T10 to Update Firmware

  1. Android Update: Download and install Device Helper before upgrading.
  2. T10 Upgrade: Connect T10 to the phone via Bluetooth. Turn off the main unit, then press and hold button "A" and long-press the power button to turn it on. Button "A"'s light will flash slowly, indicating downloading. Open the Skydroid Device app, click "updating", choose to update the controller, and click "checking updating". If new firmware is available, click "update at once".
  3. R10 Update: Connect R10 to the phone via Bluetooth, ensuring the main unit is on and paired with R10 (green light turning on). Open the Skydroid Device app, click "updating", choose to update the receiver, and click "checking updating". If new firmware is available, click "update at once".
Demonstration of Skydroid T10 system in operation, showing FPV feed and map data.

Maintenance

Storage for Not Using for a Certain Period

Store the T10 in a dry and ventilated area. Avoid direct sunlight to prevent harm to the internal Lipo battery. If storing for over three months, it is highly recommended to keep it at room temperature between 22°C to 28°C. DO NOT store it below 20°C or higher than 45°C.

Charging Precautions

Pay attention

The T10 main unit (ground terminal) uses two 18650 batteries and is compatible with standard micro USB, 5V power adapters (e.g., mobile phone, camera, or other digital product USB chargers) for charging.

In case of smoke, heat, or an unusual smell during charging, immediately stop charging the controller and return it for servicing. Do not leave the product unattended while charging. Do not leave the product in a place where children can reach. DO NOT charge when room temperature is over 60°C.

Troubleshooting (Q&A)

Q: What is the Video/Data distance of T10 in transmission?
A: Under an open area, the max distance of video link is 10km while data link is 20km.
Q: Does T10 support PPM, SBUS?
A: Yes! The SBUS port is defaulted in the first row. If you need a PPM signal, it can be switched in the Device Helper App.
Q: How to define two antennas on T10?
A: The two antennas are for 2.4GHz redundant design. We use diversity technology so both antennas perform data link and transmission.
Q: How to define two antennas on receiver?
A: The two antennas on the Receiver are for redundant design and telemetry.
Q: How to charge T10?
A: Use the micro USB cable provided with T10. Please use a certified 5V charger. LED status: LED flashes during charging and turns off when it is full.
Q: How to power on/off the T10?
A: Short press and then long press the power switch.
Q: No LED indication on the receiver when plugged into the flight control board?
A: The T10 might be powered off. If the issue persists, check the battery status (short press power switch to check the battery level). If not bound, then bind it.
Q: How to change Mode?
A: Monitor the system linked up with the radio by Bluetooth, then open Device Helper to select mode 1 or mode 2 and save. No need to set others.
Q: How to calibrate neutral of the gimbal?
A: For calibration instructions, please visit www.skydroid.xin and watch the video.
Q: How many times of command are sent out per second?
A: 300 times per second.
Q: Does T10 bind with a new receiver?
A: T10 sends a binding signal with an ID to bind a new receiver. Once a new one is bound, the old receiver needs to be rebound afterwards.
Q: What is the definition of the sound buzzer?
A: 3 short beeps: power on. 4 short beeps: binding succeeded. Continuous short beeps: battery low level. Slow continuous beeps: receiver not turned on or disconnected.

User Tips

  • Ensure proper antenna positioning on both the controller and the UAV for optimal signal strength and range.
  • Regularly check the battery level of your T10 controller to avoid unexpected power loss during operation.
  • Keep the firmware updated using the Skydroid Device Helper app for the best performance and access to new features.
  • For complex setups or troubleshooting, refer to the official Skydroid website for video tutorials and detailed guides.

Warranty & Support

For further support, firmware updates, and video demonstrations, please visit the official Skydroid website:

www.skydroid.xin

Download Skydroid Apps

Scan the QR codes below to download the necessary applications:

QR code for Device Helper app
Device Helper
QR code for Skydroid FPV app
Skydroid FPV
QR code for Skydroid Tower app
Skydroid Tower

Device Helper: Used for radio parameter adjustment, firmware upgrade, saving models, mode change, etc.

Skydroid FPV: Used for linking Skydroid video, floating window (requires Android system feature), VR, video capture, and data rate adjustment.

Skydroid Tower: Optimized by Tower 4.0, connects to Mavlink protocol of APM, PX4 flight controller to realize waypoint data telemetry. Also has video serial port (similar to DJI Go).

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.