1. Introduction
This manual provides essential information for the safe and effective use of your KKMOON BX20, BX15, or BX7 blue-violet light laser module. Designed for precision engraving and cutting, these modules are compatible with the VG-L7 Laser Engraving Machine and similar DIY laser engravers. Please read this manual thoroughly before operation to ensure proper setup, usage, and maintenance.
2. Safety Information
DANGER: AVOID EXPOSURE TO DIRECT OR SCATTERED RADIATION. THIS PRODUCT IS A CLASS IV LASER PRODUCT.
- Always wear appropriate laser safety goggles (OD4+ or higher) when operating the laser module.
- Never look directly into the laser beam or at its reflection.
- Ensure the work area is well-ventilated to dissipate fumes from engraving/cutting materials.
- Keep children and pets away from the laser engraving machine during operation.
- Do not leave the laser module unattended while it is operating.
- Ensure the laser module is securely mounted before use.
- Be aware of flammable materials in the vicinity of the laser.
- Disconnect power before performing any maintenance or adjustments.
3. Product Overview
The KKMOON laser module is a professional-grade component featuring high speed, precision, and stability. It emits a bright blue-violet light at a wavelength of 445nm, making it suitable for a wide range of engraving and cutting tasks.
3.1 Package Contents
- 1 x Laser Head (7W/15W/20W, depending on model)
- 1 x Mounting Panel
- 1 x Connection Cable
3.2 Key Features
- Adjustable laser head for precise focusing.
- Durable and stable design, tested for high temperature and long-term aging.
- Supports PWM/TTL signal controls for power modulation.
- Active/Forced Air Cooling for optimal performance.
- Engraving accuracy up to 0.05 mm.
- Fast operation speed with low noise.
Figure 1: KKMOON Laser Module (BX15 shown) with connection cable and control board.
4. Specifications
| Parameter | Value |
|---|---|
| Brand Name | KKMOON |
| Model Number | BX7, BX15, BX20 Laser Module |
| Laser Power | 7W / 15W / 20W (Optional) |
| Light Color | Blue-violet |
| Wave Length | 445nm |
| Facula Form | Punctiform, Adjustable Focus |
| Input Voltage | 12V 5A |
| Drive Mode | Extraposition ACC Constant Current |
| Cooling Mode | Active / Forced Air Cooling |
| Interface Parameter | Support PWM/TTL signal controls power |
| Item Size | 11.8 x 6.5 x 4.3 cm (4.64 x 2.55 x 1.69 in) |
| Item Weight | 279g (9.84oz) |
| Origin | Mainland China |
| Certification | CE |
| Condition | New |
| CNC or Not | Normal |
Figure 2: Back view of BX7 Laser Module with model and power information.
Figure 3: Back view of BX15 Laser Module with model, power, and control information.
Figure 4: Back view of BX20 Laser Module with model, power, and control information.
5. Setup
This laser module is designed for easy integration with compatible laser engraving machines, such as the VG-L7 Desktop DIY Engraving Machine.
- Unpacking: Carefully remove all components from the packaging. Verify that all items listed in the "Package Contents" section are present.
- Mounting: Attach the laser head to your engraving machine's mounting bracket using the provided panel and screws. Ensure it is securely fastened and stable.
- Connecting the Cable: Connect the provided cable to the laser module and to the corresponding port on your engraving machine's control board. Pay attention to the pin orientation to avoid damage. The cable typically includes connections for power (12V 5A) and PWM/TTL control signals.
- Power Supply: Connect your engraving machine to a suitable 12V 5A power supply.
- Software Setup: Refer to your engraving machine's software manual for instructions on configuring the laser module settings, including power, speed, and focus.
Figure 5: Detailed view of the laser module, highlighting the focus adjustment knob and cooling fan.
6. Operating Instructions
Before operating, ensure all safety precautions are followed, and you are wearing laser safety goggles.
- Material Placement: Place the material to be engraved or cut on the machine's work surface, ensuring it is flat and secure.
- Focus Adjustment: The laser module features an adjustable focus. For optimal results, especially for engraving stainless steel or black anodized aluminum, adjust the focus to approximately 10mm from the material surface. This is typically done by rotating the knob on the laser head until the laser dot is at its smallest and most intense point on the material surface.
- Software Configuration: Load your design into the engraving software. Set the appropriate power, speed, and passes based on the material type and desired outcome.
- Test Engraving: It is highly recommended to perform a small test engraving on a scrap piece of the same material to fine-tune settings before starting the main project.
- Start Operation: Initiate the engraving or cutting process through your machine's control software. Monitor the process closely.
6.1 Engravable and Cuttable Materials
- Engravable/Cuttable: All wood, bamboo, paper, plastics, leather, rubber, horn, sponge sheet, non-woven fabric, paper fleece, foam, stickers, KT board (up to 5mm thick).
- Engravable (with 10mm focus adjustment): Stainless steel metal, aluminum black anode (metal surfaces with paint can also be carved).
6.2 Non-Engravable Materials
- All raw metals (except stainless steel and black anodized aluminum), stone, ceramics, jewelry, silver, reflective materials, translucent & transparent materials.
Figure 6: Adjusting laser focus to 10mm for engraving stainless steel and black anodized aluminum.
Figure 7: Overview of materials compatible with the laser module.
Figure 8: Examples of engraving on various materials.
Figure 9: Diverse applications of the laser module for engraving.
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your laser module.
- Lens Cleaning: Periodically clean the laser lens with a soft, lint-free cloth and a small amount of isopropyl alcohol. Ensure the laser is off and cooled down before cleaning.
- Fan Cleaning: Keep the cooling fan free from dust and debris to ensure efficient heat dissipation. Use compressed air to gently clear any blockages.
- Module Inspection: Regularly inspect the module for any signs of damage, loose connections, or unusual wear.
- Storage: When not in use, store the laser module in a dry, dust-free environment, away from direct sunlight and extreme temperatures.
8. Troubleshooting
- Laser not firing:
- Check all cable connections to ensure they are secure.
- Verify the power supply is correctly connected and providing 12V 5A.
- Ensure the software settings are correctly configured to enable the laser.
- Confirm the laser module is compatible with your engraving machine.
- Poor engraving quality:
- Adjust the laser focus. The laser spot should be as small and sharp as possible on the material surface.
- Check the material type and adjust power/speed settings accordingly.
- Ensure the material is flat and securely held.
- Clean the laser lens if it appears dirty.
- Overheating:
- Ensure the cooling fan is operating correctly and is not obstructed.
- Operate the module within its specified parameters (12V 5A input).
- Ensure adequate ventilation in the work area.
9. User Tips
- Material Testing: Always perform small test engravings on new materials or when changing settings significantly. This helps in finding the optimal power and speed settings without wasting your main workpiece.
- Ventilation is Key: Even with the module's internal cooling, good room ventilation is crucial, especially when engraving materials that produce smoke or fumes.
- Focus for Detail: For very fine details, take extra time to ensure the laser is perfectly focused. A sharper focus results in cleaner lines and more precise cuts.
10. Warranty and Support
KKMOON provides a 12-month limited manufacturer's warranty for defective items from the date of receipt. Accessories typically come with a 3-month warranty. This warranty does not cover items damaged due to misuse or improper handling.
For warranty claims or technical support, please contact your retailer or the manufacturer directly with your order number and a detailed description of the issue. Ensure you report any defects within the warranty period and return items in their original packaging if required.