1. Introduction
The YHDC SCT-013 is a high-quality, non-invasive current transformer (CT clamp sensor) designed for accurate measurement of AC current. Its 'open-close' design allows for easy installation around a conductor without the need to break the circuit, making it ideal for various monitoring and automation applications. This sensor is particularly popular among DIY enthusiasts and for projects involving platforms like ESPHome due to its ease of use and reliable performance.
It is suitable for monitoring current in lighting equipment, AC motors, air compressors, and other electrical systems, providing essential data for current measurement and protection.
2. Safety Information
Please read and understand the following safety precautions before installing or operating the SCT-013 current transformer:
- Always ensure power is disconnected from the circuit before installing or removing the CT clamp to prevent electrical shock.
- Do not exceed the rated current or voltage specifications of the device.
- The device is designed for AC current measurement only. Do not use it for DC current.
- Ensure the CT clamp is securely closed around the conductor to ensure accurate readings and prevent accidental dislodgement.
- This product is intended for use by individuals with appropriate electrical knowledge and experience.
- The device meets UL94-V0 flame retardant properties, but it should not be exposed to excessive heat or open flames.
3. Specifications
| Feature | Specification |
|---|---|
| Model | SCT-013 Non-invasive current transformer |
| Rated Input Current | Available in various ratings (e.g., 10A, 20A, 30A, 50A, 60A, 100A) |
| Output Type | Current output or Voltage output (with built-in sampling resistor) |
| Non-linearity | +/-3% (10%-120% rated input current) |
| Core Material | Ferrite |
| Dielectric Strength | 6000V AC/1min |
| Anti-flaming Rate | UL94-V0 |
| Mechanical Strength | Opening and closing times: no less than 1000 times (at 20°C) |
| Opening Size | Approx. 0.51 x 0.51 inch / 13 x 13 mm |
| Working Temperature | -25°C to 70°C |
| Cable Length | Approx. 41.37 inch / 105 cm |
The SCT-013 is available in various current ratings and output types. Ensure you have selected the correct model for your application.
4. Package Contents
The standard package for the YHDC SCT-013 current transformer typically includes:
- 1 x YHDC SCT-013 Non-Invasive Current Transformer (with specified current rating and output type)
- Integrated cable with 3.5mm jack (for most models)
5. Setup Instructions
The SCT-013 is designed for non-invasive current measurement, meaning it can be installed without cutting or modifying the electrical wire. Follow these steps for proper setup:
- Identify the Conductor: Locate the single live wire (phase wire) of the AC circuit you wish to monitor. The CT clamp should only enclose one conductor. Clamping around both live and neutral wires will result in zero reading as the magnetic fields cancel out.
- Open the Clamp: Gently press the latch mechanism on the side of the CT clamp to open its jaws.
- Position the Clamp: Carefully place the open jaws around the identified live conductor.
- Close the Clamp: Ensure the conductor is centered within the clamp's opening and firmly close the jaws until the latch clicks into place. Verify that there are no gaps and the clamp is fully sealed.
- Connect the Output: Plug the 3.5mm jack cable from the SCT-013 into your data acquisition system, microcontroller (e.g., ESP32/ESP8266), or energy monitoring device. Ensure your device's input is compatible with the CT's output type (current or voltage).
- Power On: Once the CT is securely installed and connected, you can re-apply power to the circuit.
6. Operating Instructions
The SCT-013 operates by inducing a current or voltage proportional to the AC current flowing through the conductor it encloses. The output signal can then be read and processed by a compatible monitoring system.
- Current Output Models (e.g., 100A/50mA): These models output a small AC current (e.g., 50mA for 100A primary current). This output typically requires an external burden resistor to convert the current into a measurable voltage for analog-to-digital converters (ADCs).
- Voltage Output Models (e.g., 100A/1V): These models have a built-in sampling (burden) resistor and directly output an AC voltage (e.g., 1V for 100A primary current). This output is generally easier to interface with microcontrollers and ADCs, often requiring only a voltage divider and DC offset for safe measurement within the ADC's input range.
Refer to the documentation of your specific monitoring platform (e.g., ESPHome, Arduino) for details on how to correctly interface and calibrate the CT sensor for accurate current and power readings.
7. Maintenance
The YHDC SCT-013 current transformer is a low-maintenance device. To ensure its longevity and continued accuracy:
- Keep the device clean and free from dust and debris. Use a soft, dry cloth for cleaning.
- Avoid exposing the device to extreme temperatures, humidity, or corrosive environments beyond its specified operating range.
- Periodically check the cable for any signs of damage or wear.
- Ensure the clamp mechanism operates smoothly and closes securely.
- Do not attempt to disassemble the unit, as this may damage the internal components and void any warranty.
8. Troubleshooting
If you encounter issues with your SCT-013 sensor, consider the following troubleshooting steps:
- No Reading or Incorrect Reading:
- Ensure the CT clamp is securely closed around a single live conductor. If it's clamped around both live and neutral, it will read zero.
- Verify that the cable is properly connected to your monitoring device.
- Check the wiring and configuration of your monitoring system (e.g., burden resistor value for current output models, ADC setup for voltage output models).
- Confirm that the current being measured is within the rated range of your specific SCT-013 model.
- Inconsistent Readings:
- Ensure the conductor is centered within the clamp's opening.
- Check for any external magnetic interference near the CT clamp.
- Verify the stability of the power supply to your monitoring device.
- Physical Damage:
- Inspect the clamp for any cracks or damage that might prevent it from closing properly.
- Check the cable for cuts or frayed wires.
9. User Tips
- This product is highly suitable for DIY enthusiasts and those working on home automation projects, especially with platforms like ESPHome.
- For voltage output models, remember to add a DC offset to the AC signal if your ADC requires it to measure the full waveform (e.g., for RMS calculations).
- When using current output models, select a burden resistor that provides a suitable voltage swing for your ADC without exceeding its maximum input voltage.
10. Warranty and Support
For warranty information and technical support, please refer to the seller or manufacturer's official website. Keep your purchase receipt as proof of purchase.
Manufacturer Website: www.yhdc.com